Extron DTP3 T 311 Manual de Usario
Extron
extensor AV
DTP3 T 311
Lee a continuación 📖 el manual en español para Extron DTP3 T 311 (4 páginas) en la categoría extensor AV. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
1
DTP3 TR 311 • Setup Guide
IMPORTANT NOTE:
Go to www.extron.com for the complete user guide, installation instructions, and specications
before connecting the product to the power source.
DTP3 T 311 DTP3 R 311
This guide provides quick start instructions for an experienced installer to set up and operate the DTP3 T 311 transmitter and
DTP3 R 311 receiver. These DTP3 digital video Extenders can extend the following up to 230 feet (70 meters), using shielded
twisted pair cabling:
• HDMI digital video signal to 4K @ 60 Hz (4:4:4) (can include embedded digital audio)
• Optional analog audio • USB HID and USB 2.0
• Bidirectional RS‑232 control • Remote power (receiver to transmitter)
NOTE: Maximum transmission distances vary with resolutions used, cable types, and environment (see the
DTP3 T/R 311 User Guide at www.extron.com for full specifications).
PO WER
1.0 A MAX
12V
DT P3 IN
SIG LINK
RS-23 2
Tx Rx G
OVER D T P3
SEND
PWR
OFF AUDIO
L R
R
DEVICES
USB HID
USB 2.0
HDMI
OUT P UT S
3
4
1
2
PO WER
2.8 MAX
12V
DT P3 OU T
SIG LIN K
RS-23 2
Tx Rx G
OVER DT P3
AUDIO HOS T
R
BA
HDMIHDMI
OUT P UT S
INPUT S
PO WER STANDBY
Table
Microphone
Camera
Comput
er
75" h D yTouc ispla
CAT6A Cable
up to 230' (70 m)
USB
USB
4K/60
HDMI
4K/60
HDMI
Audi
o
USB
USB
Extron
SB 33 A 75-80 d rSoun Ba
Extron
DTP3 R 311
ReceiverExtron
DTP3 T 311
Tra rnsmitte
Figure 1. Typical DTP3 T/R 311 Transmitter and Receiver Application
Installation
Turn off and disconnect all equipment power sources and mount the transmitter and receiver Extender units as required. The
units can be mounted in a variety of locations using optional Extron mounting accessories (see www.extron.com to determine
the compatible mounting options).
Rear Panel Connections
POWER
1.0 A MAX
12V
DTP3 IN
SIG LINK
RS-232
Tx Rx G
OVER DTP3
SEND
PWR
OFF AUDIO
L R
R
DEVICES
USB HID
USB 2.0
HDMI
OUTPUTS
3
4
1
2
LLLIII MMM KKK
JJJ OOO
POWER
2.8 A MAX
12V
DTP3 OUT
SIG LINK
RS-232
Tx Rx G
OVER DTP3
AUDIO
DTP3 T 311
DTP3 R 311
HOST
R
BA
HDMIHDMI
OUTPUTS
INPUTS
AAA FFF EEEBB
B H
HHCC
C D
DD
NNN
GGG
Figure 2. DTP3 T/R 311 Rear Panel Connectors and Features
2
DTP3 TR 311 • Setup Guide (Continued)
Transmitter Features
A HDMI input port (see figure 2 on page 1) — Connect an HDMI cable between this port and the HDMI output port
HDMI
(or DVI port, with an appropriate adapter) of the digital video source. The transmitter also accepts embedded
digital audio on this port.
NOTE: See LockIt™ Lacing Brackets on page 3 to use the included Extron LockIt HDMI Cable Lacing
Bracket to secure the connector to the transmitter for
A and E.
B Audio input connector — If desired, plug an analog audio input into the transmitter via this stereo mini jack.
AUDIO
NOTE: The analog audio input is in addition to the digital audio that may be embedded in the HDMI input.
C USB Host input port — Connect a USB Type A to B cable between this USB type B port and the USB port of a
HOST
host device.
D Over DTP3 port — Connect a serial RS‑232 signal to this 3.5 mm, 3‑pole captive screw connector for
RS-232
Tx Rx G
OVER DTP3
bidirectional RS‑232 (see on page 4 to wire the connector).
Over DTP3 connector port
E HDMI output port — Connect a display to this female HDMI connector for local loop‑through monitoring of the
HDMI
source signal.
F — Connect one end of a TP cable to this RJ‑45 female connector. Ensure the opposite DTP3 OUT (TP) port
DTP3 OUT
SIG LINK
end of this cable is connected to the receiver TP Input port (see
I, below).
Use Extron XTP DTP 22 STP cable for the best performance. At minimum, Extron recommends 22 AWG, solid
conductor, STP cable with a minimum bandwidth of 500 MHz.
Terminate cables with shielded connectors to the TIA/EIA‑T568B standard (see on page 4).
DTP3 (TP) port
Limit the use of more than two pass‑through points, which may include patch points, and punch down connectors. If these
pass‑through points are required, use shielded couplers and punch down connectors.
ATTENTION:
• Do not connect these devices to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
Signal LED — Indicates the unit is outputting a DTP3 signal.
Link LED — Indicates a valid link is established between the units on the DTP3 input and output cable.
G Power connector (required, if receiver, I, is not sending power ) — Plug an optional external 12 VDC power
POWER
2.8 A MA
X
12V
supply into this 2‑pole connector (see on page 4).
Power port
ATTENTION:
• Do not connect any external power supplies until you have read the Attention notications in the Power
Supply section of the .DTP3 T/R 311 User Guide
• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section «
Power Supply » du .DTP3 T/R 311 User Guide
H RESET button — This button initiates two levels of reset (see the DTP3 T/R 311 User Guide, at ).www.extron.com
Receiver Features
DTP3 IN
SIG LINK
SEND
PWR
OFF
I — Connect one end of the TP cable from the transmitter DTP3 IN (TP) port and SEND PWR switch
output connector to this RJ‑45 female connector. Ensure the opposite end of this cable is connected to the
Output RJ‑45 connector on a compatible transmitter.
3
ATTENTION:
• Do not connect these devices to a telecommunications or computer data network.
• Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
Send Power switch — Set the switch as desired:
OFF (default) — Do not send power. The transmitter must receive power from an optional local power supply.
SEND PWR – Send 48 VDC power across the TP cable to remotely power the transmitter.
NOTE: Remote power to the transmitter is only available if the transmitter is also in the Extron DTP3 series. The
switch should be OFF for any other transmitter type.
Signal LED — Indicates the unit is receiving a valid signal on the DTP3 IN connector.
Link LED — Indicates a valid link is established between the units on the DTP3 cable.
J HDMI Output port (see figure 2 on page 1)— Connect a video display to this HDMI connector.
HDMI
NOTE: See on page 3 to use the bracket to secure the connector to the unit.LockIt™ Lacing Brackets
K Audio Output port— This 5‑pole, 3.5 mm captive screw connector outputs the transmitted, unamplified, line
AUDIO
L R
level analog audio. Connect an audio device, such as an audio amplifier or powered speakers (see Analog
audio output port on page 4 to wire the connector).
L — The four port hub has female USB Type A connectors; two are HID (keyboard USB Device ports
USB HID
USB 2.0
3
4
1
2
and mouse only) and two that are USB 2.0 (all USB devices, such as thumb drives and cameras). HID
ports can provide 100 mA to power connected peripherals. USB 2.0 ports can provide 500 mA. An
external hub can be connected only to a USB 2.0 port and adds to the total system hub count.
M — Connect a serial RS‑232 signal to this 3.5 mm, 3‑pole captive screw connector for Over DTP3 port
RS-232
Tx Rx G
OVER DTP3
bidirectional RS‑232 communication (see on page 4 to wire the connector).
Over DTP3 connector port
N — Plug an external 12 VDC power supply into this 2‑pole connector (see on page 4). Power connector Power port
POWER
1.0 A MA
X
12V
ATTENTION:
• Do not connect any external power supplies until you have read the Attention notications in the Power
Supply section of the .DTP3 T/R 311 User Guide
• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section «
Power Supply » du .DTP3 T/R 311 User Guide
O Reset button — This button initiates two levels of reset (see the DTP3 T/R 311 User Guide, at www.extron.com).
LockIt™ Lacing Brackets
Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as follows:
1. Plug the HDMI cable into the panel connection.
333
111
555
444
222
2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt
lacing bracket to be placed over it. The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then tighten
the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The shield it fastens
to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel
elle est attachée est très n et peut facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown.
5. Hold the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any excess length.
Especificaciones del producto
| Marca: | Extron |
| Categoría: | extensor AV |
| Modelo: | DTP3 T 311 |
¿Necesitas ayuda?
Si necesitas ayuda con Extron DTP3 T 311 haz una pregunta a continuación y otros usuarios te responderán
extensor AV Extron Manuales
27 Octubre 2024
19 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
extensor AV Manuales
- extensor AV Philips
- extensor AV Abus
- extensor AV Allnet
- extensor AV Nedis
- extensor AV Eminent
- extensor AV Manhattan
- extensor AV Black Box
- extensor AV Tripp Lite
- extensor AV Vision
- extensor AV DataVideo
- extensor AV Techly
- extensor AV Bogen
- extensor AV Matrox
- extensor AV Steren
- extensor AV Digitus
- extensor AV LevelOne
- extensor AV Planet
- extensor AV Konig
- extensor AV D-Link
- extensor AV One For All
- extensor AV Marmitek
- extensor AV Genexis
- extensor AV ATen
- extensor AV Gefen
- extensor AV Peerless
- extensor AV Adder
- extensor AV Monoprice
- extensor AV Crestron
- extensor AV Smart-AVI
- extensor AV StarTech.com
- extensor AV SIIG
- extensor AV Polycom
- extensor AV Micro Connect
- extensor AV KanexPro
- extensor AV Intelix
- extensor AV ASSMANN Electronic
- extensor AV Blustream
- extensor AV Avocent
- extensor AV Intellinet
- extensor AV Ebode
- extensor AV Ecler
- extensor AV Rose Electronics
- extensor AV Epcom
- extensor AV Kramer
- extensor AV CYP
- extensor AV TV One
- extensor AV SmartAVI
- extensor AV IMG Stage Line
- extensor AV Lindy
- extensor AV Atlona
- extensor AV HELGI
- extensor AV Lightware
- extensor AV Vivolink
- extensor AV AMX
- extensor AV WyreStorm
- extensor AV Rocstor
- extensor AV MuxLab
- extensor AV Seco-Larm
- extensor AV ConnectPro
- extensor AV Kanex
- extensor AV TechLogix Networx
- extensor AV C2G
- extensor AV SEADA
- extensor AV Comprehensive
- extensor AV PureLink
Últimos extensor AV Manuales
27 Octubre 2024
22 Octubre 2024
22 Octubre 2024
20 Octubre 2024
19 Octubre 2024
19 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024