Fender KXR 200 Manual de Usario

Fender Teclado KXR 200

Lee a continuación 📖 el manual en español para Fender KXR 200 (7 páginas) en la categoría Teclado. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/7
T H E S O U N T H A T C R E A T E S L E G E N D SD
P/N 048502
Two hundred
Owner,s Manual
KEYBOARD
EXTENDED
RANGE
Your new Fender®KXR 200 keyboard amplifier is the result
of Fender's®ongoing dialog with many of today's top musi-
cians. The KXR 200 uses state of the art technology to
deliver clear, resonant and most importantly...musical
sound.
The KXR 200 is actually much more than a keyboard amp.
With its heavy-duty Fender®Special Design speaker and
dual piezo-electric horn, it could actually be classified as a
self-contained, portable P.A. system. The KXR 200 is suit-
able for almost any musical instrument requiring full-range
reinforcement, for example, electronic keyboards,
acoustic/electric guitar, electric violin and also vocals.
Compact packaging and high output power make the KXR
200 the perfect full-range instrument amplifier for
rehearsal, studio or performances.
The preamp section of the KXR 200 features four indepen-
dent channels. Channels one, two, and three each feature
a single 1/4 inch, high-impedance-input jack, a three-
band equalizer, a channel volume control, an effects send
control and a reverb send control. Emphasizing on vocal,
channel four is equipped with a low impedance XLR jack in
addition to the 1/4 inch jack. Furthermore, channel four
also features a four-band equalizer centered around the
vocal frequencies, while still covering the whole audible
audio spectrum. Channel four is also equipped with a
channel volume control, an effects send control and a
reverb send control. In addition to the features mentioned
above, each channel also possesses an independent effects
loop insertion point on the rear panel. This feature makes
the KXR 200 even more versatile.
The KXR 200 is also equipped with a master section which
contains a master volume control, an effect return control, a
reverb return control, an effects send jack, an effects return
jack, and a line-out portion comprising of a 1/4 inch and
XLR jacks.
The KXR 200 keyboard amplifier was designed to give
years of reliable service under all conditions and is
equipped with a unique implementation of our exclusive,
defeatable DELTACOMPTM compressor system. When
DELTACOMPTM is engaged, it is practically impossible to
cause the power amplifier to clip (distort). With DELTA-
COMPTM, apparent compressor release time is kept short,
yet waveform distortion is kept to a minimum at low fre-
quencies.
The selection of a Fender®amplifier will reward you with
years of quality music in a wide range of sonic possibilities.
This manual is designed to familiarize you with the features
and functions of your KXR 200 amplifier. Read this manu-
al carefully so you will benefit from these features as soon
as you start using your new Fender®amplifier.
The built-in quality of a Fender®amplifier is the result of
over four decades of dedication in the combined skills of
the Fender®design team. That’s why we proudly say,
FENDER®... The Sound That Creates Legends.
INTRODUCTION
CHANNEL 1 INPUT (1/4 INCH) - Plug-in connector for
instruments. This balanced input can handle as much
as 8V R.M.S.
CHANNEL 1 VOLUME CONTROL - This control adjusts
the preamplifier gain of channel 1. It works in con-
junction with the Master Volume control ( item I) to set
the overall loudness of the amplifier for channel 1
only. Being a true “gain” control, it allows for the use
of a variety of microphones, keyboards or other instru-
ments with differing output signal levels. Low-level
instruments generally require a higher Channel
Volume setting while “hotter” keyboards will require a
lower setting.
CHANNEL 1 EQUALIZER - This equalizer allows
adjustments of the tonal characteristics of channel 1
before amplification. Each control provides a 12dB
boost or cut to bands of frequencies centered about
130, 540, and 4200 Hz. Note that all equalizer sec-
tions of the KXR 200 are designed so that if all center
frequencies are set at +12dB, a flat overall response
would be obtained. This is very useful if the signal
source is weak.
CHANNEL 1 EFFECTS SEND CONTROL - This control
works in conjunction with the effects send jack (item R),
effects return jack (item S), and the effect return con-
trol (item J) to , respectively, allow a desired amount of
preamp signal to be massaged, and to control the
amount of return signal that has gone through an
external effects device. The effects send control in con-
junction with the effects send jack could be used to
drive another KXR 200 as a slave amp. This is done
by connecting the effects send jack, with a standard
guitar cord, to the effects return jack of another KXR
200. Note that each channel could be set to send a
different amount of signal to the effects bus.
CHANNEL 1 REVERB SEND CONTROL - This control
works in conjunction with the reverb return control
(item K) to allow the amount of reverb to be mixed
with the dry signal. The amount of reverb-sent signal
is independent for each channel.
CHANNEL 2 AND 3 - These two channels are provid-
ed for two additional instruments. All the controls and
jacks operate in the same manner as those in channel
1. When not in use, it is best to turn the channel vol-
ume, the effects send and the reverb send controls all
the way down to avoid any amplification of unwanted
noise. Likewise, when not in use, the equalizer sec-
tions should be kept flat ( i.e. all knobs should be set at
12 O’clock).
CHANNEL 4 - This channel operates in the same man-
ner as the other three channels, but with the addition
of a few extra features: The XLR jack and an extra
band in the equalizer section. With the vocalist in
mind, the balanced, low impedance XLR jack provides
a suitable connection for a microphone. Furthermore,
the four-band equalizer was designed around the
A.
B.
C.
D.
E.
F,G.
H.
CHANNEL 3
VOLUME
5
0 10
HIGHMIDLOW
0
-12 +12
0
-12 +12
0
-12 +12
REVERBEFFECTS
5
0 10
5
0 10
SEND VOLUME
5
0 10
LOW
0
-12 +
1
CHANNEL 1
VOLUME
5
0 10
HIGHMIDLOW
0
-12 +12
0
-12 +12
0
-12 +12
REVERBEFFECTS
5
0 10
5
0 10
SEND
CHANNEL
VOLUME
5
0 10
MIDLOW
0
-12 + 12
0
-12 + 12
INPUT
INPUT
INPUT
INPUT MIC
AB C D EF
G
KXR 200 FRONT PANEL FUNCTIONS

Especificaciones del producto

Marca: Fender
Categoría: Teclado
Modelo: KXR 200

¿Necesitas ayuda?

Si necesitas ayuda con Fender KXR 200 haz una pregunta a continuación y otros usuarios te responderán


Teclado Fender Manuales

Fender

Fender KXR 100 Manual de Usario

26 Agosto 2024
Fender

Fender KXR 60 Manual de Usario

24 Agosto 2024
Fender

Fender KXR 200 Manual de Usario

17 Agosto 2024

Teclado Manuales

Últimos Teclado Manuales

Digitech

Digitech iPB-10 Manual de Usario

27 Octubre 2024
Kawai

Kawai ESX Manual de Usario

27 Octubre 2024
Patriot

Patriot Viper V765 Manual de Usario

26 Octubre 2024
Casio

Casio MZ-X500 Manual de Usario

23 Octubre 2024
Casio

Casio WK-1630 Manual de Usario

23 Octubre 2024
Casio

Casio ToneBank CT-636 Manual de Usario

23 Octubre 2024
Casio

Casio Privia PX-830 Manual de Usario

23 Octubre 2024
Casio

Casio 100 ToneBank SA-1 Manual de Usario

23 Octubre 2024
Casio

Casio CTK-3400SK Manual de Usario

23 Octubre 2024
Yamaha

Yamaha PSR-E413 Manual de Usario

23 Octubre 2024