Festo VMPAL-LW Manual de Usario

Festo Sapcentrifuge VMPAL-LW

Lee a continuación 📖 el manual en español para Festo VMPAL-LW (2 páginas) en la categoría Sapcentrifuge. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Montageanleitung (de)
755 272 / 2010-09NH
†‡
Lösehilfe
VMPAL-LW
Festo SE & Co. KG
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Teileliste
15363d_1
1 Lösehilfe
VMPAL-LW
Bestimmungsgemäß dient die
Lösehilfe 1 dazu, das Elektro-
nikmodul 3 zu demontieren.
2. Demontage:
Bei Anschlussplatte MPAL-AP-4X10
15363d_2
2 Anschlussplatte
(Baugruppe)
3 Elektronikmodul
Drehen Sie die Schraube (A)
heraus. Achten Sie auf die
Mutter (B), damit sie dabei
nicht verloren geht.
Ziehen Sie diese drei An-
schlussplatten (C) ab.
15363d_3
Führen Sie die Lösehilfe 1
in die vorgesehenen Nuten
im Elektronikmodul 3 ein.
15363d_5
Platzieren Sie alles über ei-
ner ebenen Fläche.
Drücken Sie die Lösehilfe 1
und die Anschlussplatte 2
gleichmäßig zusammen, bis
Sie spüren, dass die
Schnapphaken nachgeben.
15363d_6
Drücken Sie das Elektronik-
modul 3 gegen die ebene
Fläche und somit nach oben
aus der Anschlussplatte 2
heraus.
3. Demontage:
Bei Anschlussplatte VMPAL-AP-10 und Einspeisemodul VMPAL-SP
15363d_7
2 Anschlussplatte/
Einspeisemodul
3 Elektronikmodul
Führen Sie die Lösehilfe 1
in die vorgesehenen Nuten
im Elektronikmodul 3 ein.
15363d_8
Drücken Sie die Lösehilfe 1
und das Bauteil 2 gleich-
mäßig zusammen, bis Sie
spüren, dass die Schnapp-
haken nachgeben.
Halten Sie dies so fest.
15363d_9
Drücken Sie das Elektronik-
modul 3 gleichzeitig mit
den Daumen aus dem Bau-
teil 2 heraus.
Alternative zum einfacheren Herausdrücken des Elektronikmoduls 3:
15363d_16
Fertigen oder verwenden Sie
einen kleinen Block (A), der
ungefähr den nebenstehen-
den Maßen [mm] entspricht.
15363d_4
Stellen Sie den Block (A) un-
ter die Lösehilfe 1 auf eine
ebene Fläche.
Drücken Sie die Lösehilfe 1
und das Bauteil 2 gleich-
mäßig zusammen, bis Sie
spüren, dass die Schnapp-
haken nachgeben.
15363d_5
Drücken Sie das Elektronik-
modul 3 auf den Block (A)
und somit nach oben aus
dem Bauteil 2 heraus.
3
2
1
1
2
C
A
B
3
2
3
1
1
2
A
2
1
3
1
2
A
A
3
2
1
3
2
1
1
2
3
Assembly instructions (en)
755 272 / 2010-09NH
†‡
Releasing tool
VMPAL-LW
Festo SE & Co. KG
Postfach
D-73726 Esslingen
++49/(0)711/347-0
www.festo.com
1. Parts list
15363d_1
1 Releasing tool
VMPAL-LW
The releasing tool 1 is in-
tended for disassembly of the
electronics module 3.
2. Disassembly:
With sub-base MPAL-AP-4X10
15363d_2
2 Sub-base
(Module)
3 Electronics module
Unscrew the screw (A). Pay
attention to the nut (B) so it
does not get lost.
Pull off the three sub-
bases (C).
15363d_3
Guide the releasing tool 1
into the designated grooves
in the electronics module 3.
15363d_5
Place everything over a flat
surface.
Evenly press the releasing
tool 1 and the sub-base 2
together until you feel that
the snap-in hooks are giving
way.
15363d_6
Press the electronics mod-
ule 3 against the flat sur-
face and thus upward out of
the sub-base 2.
3. Disassembly:
For sub-base VMPAL-AP-10 and power supply module VMPAL-SP
15363d_7
2 Sub-base/
Power supply module
3 Electronics module
Guide the releasing tool 1
into the designated grooves
in the electronics module 3.
15363d_8
Evenly press the releasing
tool 1 and the compo-
nent 2 together until you
feel that the snap-in hooks
are giving way.
Hold it tight.
15363d_9
Simultaneously press the
electronics module 3 out of
the component 2 with your
thumbs.
Alternatives for pressing the electronics module 3 out more easily:
15363d_16
Make or use a small block (A)
that approximately equals
the dimensions in the figure
on the left [mm].
15363d_4
Put the block (A) underneath
the releasing tool 1 on a flat
surface.
Evenly press the releasing
tool 1 and the compo-
nent 2 together until you
feel that the snap-in hooks
are giving way.
15363d_5
Press the electronics mod-
ule 3 onto the block (A) and
thus upward out of the com-
ponent 2.
3
2
1
1
2
C
A
B
3
2
3
1
1
2
A
2
1
3
1
2
A
A
3
2
1
3
2
1
1
2
3

Especificaciones del producto

Marca: Festo
Categoría: Sapcentrifuge
Modelo: VMPAL-LW

¿Necesitas ayuda?

Si necesitas ayuda con Festo VMPAL-LW haz una pregunta a continuación y otros usuarios te responderán




Sapcentrifuge Festo Manuales

Festo

Festo VMPAL-LW Manual de Usario

26 Septiembre 2024

Sapcentrifuge Manuales

Últimos Sapcentrifuge Manuales