Fluke 700HTP-2 Manual de Usario

Fluke Pompa 700HTP-2

Lee a continuación 📖 el manual en español para Fluke 700HTP-2 (2 páginas) en la categoría Pompa. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
PN 4096896
September 2011
2011 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
How to Prime Pump the Test
Before you connect the to the Unit Under T), the Pump Test (UU
Pump must be lled with uid and primed for use. Follow the
directions below to prepare the for use. Pump
1. Fill the with uid: Pump
a. Remove the Reservoir Filler Cap (item .)
b. Fill the Hydraulic Fluid Reservoir approximately -thirds full two
(66 with distilled water, mineral oil, or hydraulic oil. cc)
Note
If water is used in the , use only DISTILLED water Pump
and drain the water out of the after use. Pump
c. Install the Reservoir Filler Cap (item .) Tighten by hand.
2. the : Prime Pump
a. Adjust the Vernier Fine Adjustment Knob (item ) to the
approximate dle-range.mid
b. Turn the Pressure Bleed Knob (item ) clockwise until it
stops in the full closed position.
c. Squeeze the handles together to pump uid. uid until Pump
uid shows at the . Pump Port
d. Attach the uid hose to the . Pump
e. Squeeze the handles together until uid shows at the end of
the hose.
f. Attach the uid hose to the Unit Under (UUT) and Test
squeeze the handles until pressure increases. Pump
g. Bleed the trapped air from the Pump. Pressurize the Pump to
1,000 psi then slowly turn the Pressure Bleed Knob (item )
counter-clockwise to release pressure.
Notes
• As the pressure it will be hard to squeeze the rises
handles together. Use the Handle Limiter (item ) to
limit the travel of the handles which will make them
easier to squeeze together. toggle the Handle To
Limiter on or o, squeeze the handles together and
push the Handle Limiter (item
) in or out.
• The rate at which the pressure increases is directly
related to the test conguration (hose length and
volume of UUT.)
Replacement Parts
Rebuild Kit, Fluke PN 4097836
Hydraulic Fluid Reservoir Rebuild , Fluke PN 2844341 Kit
Handle Assembly Rebuild , Fluke PN 2844352 Kit
LIMITED WARRANTY AND OF LIABILITYLIMITATION
This Fluke product will be from defects in material and workmanship for free
one year from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage from accident, neglect, misuse, alteration,
contamination, or conditions of operation or . Resellers are abnormal handling
not authorized any obtain to extend other warranty on Fluke’s behalf. To
service during the warranty period, contact your nearest Fluke authorized
service r cente to obtain return authorization information, then send the product
to that with a description of the problem.Service Center
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE SPECIAL, INDIRECT, IS NOT LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or of an implied warranty or of incidental or limitation
consequential damag not apply to you.es, this limitation of liability may
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
Fluke 700HTP- -2
Hydraulic Test Pump
Instruction Sheet
Introduction
The Fluke 700HTP-2 Hydraulic (the or ProductTest Pump Pump ) is a
portable source of high pressure.
Safety
W Warning
To prevent personal injury se the Product only as , u
specified, or the protection supplied by the Product can be
compromised.
Pump Sp ecifications
• Maximum pressure: 10,000 psi (690 bar)
• raulic media: distilled water, mineral based hydraulic oil, up Hyd or
to hydraulic oil 100 (30 W).
• Wetted materials: 303 stainless steel, aluminum, polyurethane,
PTFE, nitrile, and nylon.
• Weight: 1.29 lb (0.58 kg)
• Dimensions: length 9.5 41 mm), width 6.1 in (155 mm), depth in (2
2.6 in (66 mm)
Box Contents
• Model 700HTP-2 Hydraulic with a 1/4- NPT tee Test Pump inch
installed.
• 1/4- NPT male to 1/4- female adapters. Two inch inch BSP
• One 1/4- NPT male to 1/4- NPT male tting. inch inch
• One 1/4- NPT male to 1/8- NPT male tting. inch inch
• Instruction Sheet
How to Contact Fluke
To contact Fluke, call one of the following telephone numbers:
• Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
• Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
• Canada: 1-800-36-FLUKE
(1-800-363-5853)
• Europe: +31 402-675-200
• Japan: +81-3-6714-3114
• Singapore: +65-738-5655
• Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit . http://register.uke.com
To view, print, or download the latest manual supplement, visit
http://us.uke.com/usen/support/manuals.
Features
gsp001.eps
No. Item Function
Master
Instrument Port
Port for Fl uke 700 Series Pressure
Module, 1/4-inch NPT female.
Test Pressure
Port
Port for pressure instrument under
test, 1/4-inch NPT female.
Pressure Relief
Valve Port
Port for an optional Fluke 700PRV-1
Pressure Relief Valve (plugged).
Vernier Fine
Adjustment Knob
Lets you adjust the applied pressure
in small increments.
Hydraulic Fluid
Reservoir
Holds 100 cc of mineral based
hydraulic oil, distilled water, or
hydraulic oil.
1/4-inch NPT Tee
Fitting For master and test ports.
Handle Limiter Limits the travel of the handles.
Reservoir Filler
Cap
Cap which seals the hydraulic uid
reservoir. Install before you pump.
Pressure Bleed
Knob
Lets you release pressure in small
increments.
Reservoir Nut Remove nut to clean reservoir.
gsp002.eps
Figure 1. Test Configuration
How to Operate the Test Pump
W Warning
To prevent a violent release of pressure, open the
Pressure ) very slowlyBleed Knob (item before you
disconnect pressure lines. Do not connect the Pump to
an external pressure source.
W Caution
To prevent damage hen odule or w a Pressure M Pressure
I nstrument is connected that could be damaged by
pressures of 690 bar (10,000 psi), install and correctly
set a relief valve in the system or an optional Fluke
700PRV-1 Pressure Relief Valve on the . Pump
1. Connect a 700 Series Pressure Module (the Pressure Module)
to the Master Instrument (item .) To connect to a 700P Port
High Pressure Module (700P29, P30, or P31) install a male
1/4-inch NPT Adapter. Use Teon
® tape or equivalent on the
NPT thread connections to prevent leaks.
2. Fill and the . See “How to the Prime Pump Prime Test Pump”.
3. Connect the Pressure Module to the calibrator as shown in
Figure 1.
4. Connect the input of the Pressure Unit Under Test U to the (U T)
Test Port Test Pressure (item ) on the . Pump
5. Loosen the Pressure Bleed Knob (item ) to release pressure
from the . Pump
6. Use the Calibrator to z the Pressure Module. Refer to the ero
Users Manual for instructions.
7. Turn the Adjustment Knob (item ) to the Vernier Fine
middle-range.
8. Turn the Pressure Bleed Knob (item ) clockwise until it stops
in the full closed position.
9. Squeeze the handles together to pump increase fluid which will
pressure. See the Notes in step 2 of the “How to the Prime Test
Pump” procedure.
W Caution
To prevent damage, do not let the pressure increase to
more than the pressure rating of the equipment under
test. Pressure can increase quickly if the pressurized
volume is small.
10. incremental pressure adjustments, use the Vernier Fine For
Adjustment Knob.
11. Once the test is done, slowly turn the Pressure Bleed Knob
(item ) counter-clockwise to release pressure.

Especificaciones del producto

Marca: Fluke
Categoría: Pompa
Modelo: 700HTP-2

¿Necesitas ayuda?

Si necesitas ayuda con Fluke 700HTP-2 haz una pregunta a continuación y otros usuarios te responderán


Pompa Fluke Manuales

Fluke

Fluke 700LTP-1 Manual de Usario

21 Septiembre 2024
Fluke

Fluke 700HTP-2 Manual de Usario

31 Julio 2024
Fluke

Fluke 730LTP600K Manual de Usario

22 Julio 2024

Pompa Manuales

Últimos Pompa Manuales

JANDY

JANDY JCP07-3AT-S Manual de Usario

27 Octubre 2024
Gude

Gude INOX 100/24 Manual de Usario

26 Octubre 2024
Vivaria

Vivaria Vario N-3000 Manual de Usario

26 Octubre 2024
Maruyama

Maruyama MS655 Manual de Usario

26 Octubre 2024
Gardena

Gardena RWT Pump 2000/2 Li-18 Manual de Usario

15 Octubre 2024
Ozito

Ozito PTP-012A Manual de Usario

15 Octubre 2024
MSW

MSW -AN-100 Manual de Usario

15 Octubre 2024
MSW

MSW -MN34 Manual de Usario

15 Octubre 2024
MSW

MSW -MN34M Manual de Usario

15 Octubre 2024
MSW

MSW -AOP40S Manual de Usario

15 Octubre 2024