Flyzone Calypso Manual de Usario
Flyzone
juguetes radiocontrolados
Calypso
Lee a continuación 📖 el manual en español para Flyzone Calypso (4 páginas) en la categoría juguetes radiocontrolados. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
REQUIRED FOR COMPLETION
In addition to the items listed in the instruction manual for the
Rx-R edition, the Calypso ARF also requires the following items:
❍ 18A (Electronic Speed Controller) (FLZA6011)ESC
❍ C28-30 1300kV (FLZA6012)brushless motor
❍ Spinner, folding (FLZA6006)propeller set
❍ (4) Calypso micro servos (FLZA6013), or any of the
Futaba® micro servos that have the same case as the
S3117 such as the following:
◗ S3117 (FUTM0417)
◗ S3157 (FUTM0657)
◗ S3156 (FUTM0656)
❍ (2) 18"–24" [460 mm – 610 mm] servo wire extensions
for aileron servos (HCAM2200 for Futaba J)
❍ The ailerons may be mixed electronically through the
mixing in your transmitter, or “hard-wired” together into
the same channel with a (FUTM4130).Y-harness
❍ The Calypso may be assembled with just about any kind
of glue including foam-safe or regular CA, but for gluing
in the servos something thicker and fl exible is preferred
such as Zap Goo or similar (PAAR3200).
❍ A 1.5mm is required for tightening the set Allen wrench
screws in the folding propeller hub (DTXR0288).
❍ Non-permanent threadlocker for all metal-to-metal screws
(GPMR6060)
ASSEMBLY
Assemble the Wings
First, let’s center the aileron servo arms before gluing the
servos into the wing…
❏ 1. Temporarily connect the aileron servos and ESC to your
receiver and turn on your transmitter. Making sure the trims
on your transmitter are centered, connect the battery to the
ESC. If necessary, remove and re-mount the servo arms so
they will be perpendicular as shown. Be certain to replace
the servo arm screws.
You may work on both wings simultaneously, or do one
wing at a time.
❏ 2. Without using any glue, temporarily fi t the servos into the
pockets in the wing. Hook up the ailerons with the hardware shown.
❏ 3. Connect a 18" – 24" [460mm – 610mm] servo extension
to the aileron servo wires and secure the connection with tape,
Manual Supplement
Refer to this Instruction Manual Supplement
for initial assembly of your Calypso ARF.
After completing the assembly steps in
this supplement, continue with the twenty-
page RTF / Rx-R / Tx-R Calypso instruction
manual booklet.
2
heat shrink tubing or a dab of glue. Lay the servo wires down
inside the channels.
❏ 4. If you plan to hook up the optional fl aps, it will be a
little easier to cut the fl ap servo openings in the bottom wing
covers and fi t the fl ap servos at this time, so go ahead and
do so—but fi rst refer to the illustration at step 13 on page 11
of the Calypso instruction manual for the correct orientation
of the fl ap servos and servo arms. If unsure whether or not
you will be using fl aps, the servo installation and hookup is
easy enough to retrofi t later (as illustrated on page 8 of the
instruction manual).
❏ 5. Without using any glue, test-fi t the bottom wing cover to
the wing. Make sure the cover lays all the way down fl at into
the cavity and make any adjustments necessary.
❏ 6. Glue the aileron servos (and fl ap servos if installed) into
position—thick or medium CA is suitable, but if ever necessary,
the servos will be easier to extract later if something more
fl exible such as Zap Goo or similar is used.
❏ 7. Glue the bottom wing cover into position—thick or medium
CA is okay here, but not to allow any glue to leak into use care
the channel or into the clamp for the joiner tube. If necessary,
use tape or weights to hold the cover down until the glue
hardens.
❏ 8. Glue the spars and optional aileron pushrod covers into
position. Also apply a strip of white or clear tape over the
channel for the aileron servo wire.
3
Assemble the Fuselage
Non-permanent threadlocker
should be used on all screws
that thread into metal such as
the motor mount screws, the
set screws in the propeller hub
and the screws that secure the
spinner—a large amount of
threadlocker is not required—
just enough to “wet” the fi rst few
threads.
❏ 1. Guide the motor wires through the oval hole in the bottom
of the motor mount. Then, mount the motor with the two 3 x
5mm screws (don’t forget to use threadlocker on the screws).
❏ 2. Fasten the propeller hub onto the motor shaft using a
1.5mm hex wrench to tighten the set screws. Then, mount the
spinner with the 3 x 12mm screws.
❏ 3. Connect the ESC to the motor and mount the ESC to the
inside of the fuselage with strips of the included adhesive-back
hook-and-loop material. Note: If, while running up the motor
later, the propeller turns backward, simply switch any two of
the three motor wires with each other to make the motor turn
the other direction.
Especificaciones del producto
| Marca: | Flyzone |
| Categoría: | juguetes radiocontrolados |
| Modelo: | Calypso |
¿Necesitas ayuda?
Si necesitas ayuda con Flyzone Calypso haz una pregunta a continuación y otros usuarios te responderán
juguetes radiocontrolados Flyzone Manuales
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
juguetes radiocontrolados Manuales
- juguetes radiocontrolados ACME
- juguetes radiocontrolados Absima
- juguetes radiocontrolados Spektrum
- juguetes radiocontrolados Chicco
- juguetes radiocontrolados Carson
- juguetes radiocontrolados Amewi
- juguetes radiocontrolados Proline
- juguetes radiocontrolados Biltema
- juguetes radiocontrolados TacTic
- juguetes radiocontrolados Little Tikes
- juguetes radiocontrolados Revell
- juguetes radiocontrolados Futaba
- juguetes radiocontrolados Tamiya
- juguetes radiocontrolados Traxxas
- juguetes radiocontrolados ARRMA
- juguetes radiocontrolados Carrera
- juguetes radiocontrolados Graupner
- juguetes radiocontrolados Blade
- juguetes radiocontrolados Hobbywing
- juguetes radiocontrolados JETI
- juguetes radiocontrolados Ninco
- juguetes radiocontrolados Multiplex
- juguetes radiocontrolados SAB
- juguetes radiocontrolados Ripmax
- juguetes radiocontrolados Maverick
- juguetes radiocontrolados Reely
- juguetes radiocontrolados Robbe
- juguetes radiocontrolados Lenoxx
- juguetes radiocontrolados Axial
- juguetes radiocontrolados FMS
- juguetes radiocontrolados E-flite
- juguetes radiocontrolados FrSky
- juguetes radiocontrolados WLtoys
- juguetes radiocontrolados Jada
- juguetes radiocontrolados HPI Racing
- juguetes radiocontrolados Kyosho
- juguetes radiocontrolados PowerBox Systems
- juguetes radiocontrolados Losi
- juguetes radiocontrolados Hobby Zone
- juguetes radiocontrolados JR
- juguetes radiocontrolados RC4WD
- juguetes radiocontrolados Sky Rider
- juguetes radiocontrolados DF-Models
- juguetes radiocontrolados ROCHOBBY
Últimos juguetes radiocontrolados Manuales
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
26 Octubre 2024
19 Octubre 2024
15 Octubre 2024
8 Octubre 2024
4 Octubre 2024
3 Octubre 2024
3 Octubre 2024