GE JX15BUMPBB Manual de Usario

GE Magnetron JX15BUMPBB

Lee a continuación 📖 el manual en español para GE JX15BUMPBB (4 páginas) en la categoría Magnetron. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
Installation Bump-Out Kit
Instructions JX15BUMP
For 15” Deep Cabinets
49-40719-1 03-15 GE
IMPORTANT:
Use the existing mounting bracket that comes with your OTR Microwave to identify location for the Bump Out Kit.
Place the original bracket on the wall according to
installation instructions from the OTR Microwave to
determine where to place the Bump Out Kit Bracket.
Mark lowest edage of bracket
Existing Mounting Bracket
from OTR Microwave
Place the Bump Out Kit Bracet in place of existing bracket location making sure that the bottom edge lines up.
Bump-Out Kit
Bracket
2
Installation Instructions
TOOLS YOU WILL NEED
#1 and #2 Phillips screwdriver Pencil
Ruler or tape
measure and
straight edge Carpenter square
(optional)
Tin snips (for cutting
damper, if required)
Electric drill with 3ø16” , 7ø16”, 3ø8”,
1ø2” and 5ø8” drill bits
Hammer (optional)Stud finder or
Filler blocks or scrap
wood pieces, if needed
for top cabinet spacing
(used on recessed
bottom cabinet
installations only)
Gloves
Saw (saber, hole or keyhole)
Level Duct and masking tape
Scissors
(to cut template, if necessary)
Safety goggles
MOUNTING SPACE
NOTES:
The space between the cabinets must be 30” wide
and free of obstructions.
If the space between the cabinets is greater
than 30”, a Filler Panel Kit may be used to fill
in the gap between the oven and the cabinets.
Your Owner’s Manual contains the kit number for
your model.
This oven is for installation over ranges up to
36” wide.
If you are going to vent your oven to the outside,
see Hood Exhaust Section for exhaust duct
preparation.
When installing the oven beneath smooth, flat
cabinets, be careful to follow the instructions
on the top cabinet template for power cord
clearance.
Backsplash
66” or more
from the
floor to the
top of the
oven
30”
2”
30”
min.
16-1ø4”
Bottom edge
of cabinet
needs to
be 30” or
more from
the cooking
surface
NOTE: Maximum cabinet depth is 15”.
3
Installation Instructions
Find the studs, using one of the following methods:
A. Stud finder – a magnetic device which locates nails.
OR
B. Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate a stud
location.
After locating the stud(s), find the center by probing
the wall with a small nail to find the edges of the stud.
Then place a mark halfway between the edges. The
center of any adjacent studs should be 16" or 24" from
this mark.
Draw a line down the center of the studs.
THE OVEN MUST BE CONNECTED TO AT LEAST ONE
WALL STUD.
1
FINDING THE WALL STUDS
A.
2
PLACEMENT OF THE BUMP-OUT BRACKET
1
Wall Studs
Level line for front overhang
Center 3
ALIGNING THE WALL PLATE
Draw a vertical line on the wall at the center of the 30”
wide space.
Use mounting plate as the template for the rear wall.
Place mounting plate on the wall, making sure that the
tabs are touching the bottom of the cabinet or the level
line drawn for cabinets with front overhang. Line up the
notch and center line on the mounting plate to the center
line on the wall. (If the tabs are not in line with front
overhang, unit will be tilted.)
While holding mounting plate with one hand, draw circles
on the wall at holes A, B, C and D (see illustration above) .
Four holes must be used for mounting.
NOTE: Holes C and D are inside area E. If neither C nor D
is in a stud, find a stud somewhere in area E and draw
a fifth circle to line up with the stud. It is important to
use at least one wood screw mounted firmly in a stud to
support the weight of the oven.
Set the mounting plate aside.
Drill holes on the circles. If there is a stud, drill a 3ø16” hole
for wood screws. For holes that don’t line up with a stud,
drill a 5ø8” hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
2
3
4
Draw a
Vertical Line
on Wall from
Center of Top
Cabinet
Area E
Hole Location A
Hole Location B
Hole Location D
B.
CAUTION: Wear gloves
to avoid cutting fingers
on sharp edges.
1
Hole Location C
NOTE: Appearance
and shape of the
mounting plate
may vary from your
model.

Especificaciones del producto

Marca: GE
Categoría: Magnetron
Modelo: JX15BUMPBB

¿Necesitas ayuda?

Si necesitas ayuda con GE JX15BUMPBB haz una pregunta a continuación y otros usuarios te responderán


Magnetron GE Manuales

GE

GE Adora DVM7195DKWW Manual de Usario

27 Octubre 2024
GE

GE Profile PWB7030SVSS Manual de Usario

27 Octubre 2024
GE

GE GCST09U1 Manual de Usario

21 Octubre 2024
GE

GE Profile JVM1661WB Manual de Usario

11 Octubre 2024
GE

GE Profile JVM1661CB Manual de Usario

2 Octubre 2024
GE

GE EMO3000CSS Manual de Usario

30 Septiembre 2024
GE

GE HVM1540LPCS Manual de Usario

22 Septiembre 2024
GE

GE GCST09N1 Manual de Usario

18 Septiembre 2024
GE

GE GCST11N1 Manual de Usario

18 Septiembre 2024
GE

GE GCST20S1 Manual de Usario

17 Septiembre 2024

Magnetron Manuales

Últimos Magnetron Manuales

Klarstein

Klarstein Julieta Manual de Usario

27 Octubre 2024
Severin

Severin MW 9628 Manual de Usario

27 Octubre 2024
Philco

Philco PMG1620S Manual de Usario

27 Octubre 2024
Thermador

Thermador PODMW301 Manual de Usario

27 Octubre 2024
BEKO

BEKO MOC20100W1 Manual de Usario

25 Octubre 2024
Panasonic

Panasonic NN-SU656W Manual de Usario

24 Octubre 2024
Panasonic

Panasonic NN-CT552W Manual de Usario

24 Octubre 2024
Candy

Candy CMXW 30DS-UK Manual de Usario

24 Octubre 2024
Panasonic

Panasonic NN-SN936B Manual de Usario

24 Octubre 2024
Electrolux

Electrolux EI30BM55HZ Manual de Usario

24 Octubre 2024