Genelec 8020B Manual de Usario

Genelec Vocero 8020B

Lee a continuación 📖 el manual en español para Genelec 8020B (32 páginas) en la categoría Vocero. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/32
8020B
Operating Manual 2-7
Betriebsanleitung 8-13
Manuel d’utilisation 14-19
yttöohje 20-26
Bruksanvisning 25-31
2 English
General description
The bi-amplified GENELEC 8020B is an extremely
compact two way active monitoring loudspeaker
designed for near field monitoring, mobile vans,
broadcast and TV control rooms, surround sound
systems, home studios, multimedia applications and
also for use with computer soundcards. As an active
loudspeaker, it contains drivers, power ampliers,
active crossover filters and protection circuitry.
The MDE™ (Minimum Diffraction Enclosure™)
loudspeaker enclosure is made of die-cast alumin-
ium and shaped to reduce edge diffraction. Com-
bined with the advanced Directivity Control Wavegui-
deTM (DCWTM), this design provides excellent fre-
quency balance in difficult acoustic environments. If
necessary, the bass response of the 8020B’s can be
extended with a Genelec 7050B subwoofer.
Positioning the loudspeaker
Each 8020B monitor is supplied with an integrated
amplifier unit, mains cable and an operating manual.
After unpacking, place the loudspeaker in its required
listening position, taking note of the line of the acous-
tic axis. The axes of all loudspeakers should converge
at ear height at the listening position (see Figure 1).
Connections
Before connecting up, ensure that the loudspeakers
and the signal source have been switched off. The
power switch of the 8020B is located on the back
panel (see Figure 3). Connect the loudspeaker to an
earthed mains connection with the supplied mains
cable. Never connect the loudspeaker to an un-
earthed mains supply or using an unearthed mains
cable. Audio input is via a 10 kOhm balanced fe-
8020B
Active Monitoring System
English 3
male XLR connector. An unbalanced source may
be used as long as pin 3 is grounded to pin 1 at
the unbalanced source connector (see Figure 2).
Never connect the 8020B to the loudspeaker out-
puts of a power amplifier or an integrated amplifier
or receiver.
Once the connections have been made, the
loudspeakers are ready to be switched on.
Volume control
The input sensitivity of the loudspeakers can be
matched to the output of the mixing console or other
signal source by adjusting the volume control on the
front panel.
Setting the tone controls
The frequency response of the Genelec 8020B
can be adjusted to match the acoustic environ-
ment by setting the tone control switches on the
rear panel. The controls are Treble Tilt”,Bass
Tilt” and “Bass Roll-Off”. An acoustic measuring
system such as WinMLS or comparable is recom-
mended for analyzing the effects of the adjust-
ments, however, careful listening with suitable
test recordings can also lead to good results if
a test system is not available. Table 1 overleaf
shows some examples of typical settings in vari-
ous situations. Figure 4 shows the effect of the
controls on the anechoic response.
Figure 1: Location of the acoustic
axis
Figure 2: Type of cable needed if
unbalanced source is used (ex-
ample shown is RCA output to the
XLR input)
Figure 3: Control and connector layout on the rear panel
of an 8020B.

Especificaciones del producto

Marca: Genelec
Categoría: Vocero
Modelo: 8020B

¿Necesitas ayuda?

Si necesitas ayuda con Genelec 8020B haz una pregunta a continuación y otros usuarios te responderán




Vocero Genelec Manuales

Vocero Manuales

Últimos Vocero Manuales