Glide Gear POV100 Manual de Usario
Glide Gear
Trípode
POV100
Lee a continuación 📖 el manual en español para Glide Gear POV100 (3 páginas) en la categoría Trípode. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/3
POV 100
1 PLEASE NOTE:
For use with cameras weighing up to 2.5lbs or
1.15kg including the lens
The POV100 comes in 2 sizes: M (54 60cm/21.25- -
23.6”) and L (56 62cm/22 24.4- - ”)
Recommended use with wide angle lenses set to
innity focus for best results
For more informaon please visit our website: www.glidegear.net
2
Fig A
4
Mount your camera using the screw
inside the slot in the crossbar in the
front of the helmet. See Fig A.
Crossbar
Mounng
screw
3 Included with the POV 100 are 10 weight plates. With
the camera mounted in the front, your head will be
leaning forward. Add weight plates to the back of the
helmet to balance your head and ease the strain on
your neck. Use the supplied thumb nut to secure the
weight plates in an unloose posion. See Fig. B
Fig C
Hint: Weigh your camera and use the appropriate
number of plates to get as close as possible to the
camera weight knowing that 1 plate weighs about
4oz (or 100g).
Example: For a camera weighing 1.6lbs, add 6-7
plates to the back.
Thumb nut
In the rear inside of the helmet, you will nd a knob.
Use the knob to ghten or loosen the helmet s inside ’
frame so that the helmet ts ghtly on your head.
The knob in queson is circled on Fig. C.
Fig B
POV 100
5
Top Plate features:
1/4 20 female threaded holes to mount mic, lights, fricon arm etc..-
14/4 20 mounng screw to mount a GoPro, a 360 camera, light, mic, fricon -
arm etc..
For more informaon please visit our website: www.glidegear.net
Fig D
At this point, your setup should look like Fig. D. The POV 100 is a very exible head rig with mulple
adjustments and mounng possibilies. See the adjustments available below .
Front Plate features:
1/4 20 female threaded holes -
for accessories
14/4 20 mounng screw-
Crossbar Knobs:
Loosen up the knobs. Adjust the
angle of the camera. Tighten the
knobs when done.
Temple Plate:
Remove the 2 screws. While
keeping a 45 degree angle, move
the camera frame horizontally
and along the slot to adjust how
far from the face the camera will
be.
Lock in place using the 2 screws.
Use the other threaded holes to
mount accessories.
Mid –secon Knobs:
Loosen up the knobs. Adjust
the camera posion so you
can see clearly in front of
you. Tighten the knobs when
done.
POV 100
For more informaon please visit our website: www.glidegear.net
If any assembling is needed, please refer to the below secon:
BACK: Mount the plate with the longest
screw to the back of the helmet using 2 of the
supplied M3 screws. Fig E.
FRONT: Mount the curved rectangular plate
to the front of the helmet using 2 of the sup-
plied M3 screws and through the 2 slots on
the plate. Fig F.
SIDES: Mount the 2 idencal plates to the sides
of the helmet using 2 of the supplied M3 screws
and through the 2 slots on the plate. Each plate
should be oriented so that the plate s thicker end ’
faces the back of the helmet . Fig. H.
TOP: Mount the rectangular at plate to the
top of the helmet using 2 of the supplied M3
screws and through the 2 slots on the plate.
Fig G.
Thinner end
Thicker end
Fig F
Fig E
Fig G
Fig H
Especificaciones del producto
| Marca: | Glide Gear |
| Categoría: | Trípode |
| Modelo: | POV100 |
¿Necesitas ayuda?
Si necesitas ayuda con Glide Gear POV100 haz una pregunta a continuación y otros usuarios te responderán
Trípode Glide Gear Manuales
17 Septiembre 2024
16 Septiembre 2024
Trípode Manuales
- Trípode Sony
- Trípode Silvercrest
- Trípode Kodak
- Trípode Carson
- Trípode Easypix
- Trípode Hama
- Trípode Velleman
- Trípode AVerMedia
- Trípode Celestron
- Trípode DJI
- Trípode Vello
- Trípode Rollei
- Trípode Magnus
- Trípode Zhiyun
- Trípode Miller
- Trípode Benro
- Trípode Vortex
- Trípode Sachtler
- Trípode Sevenoak
- Trípode Laserliner
- Trípode Celly
- Trípode Eurolite
- Trípode Proaim
- Trípode Revo
- Trípode Konig & Meyer
- Trípode Manfrotto
- Trípode Velbon
- Trípode ARRI
- Trípode Ultimate Support
- Trípode Levenhuk
- Trípode JOBY
- Trípode Oben
- Trípode Dorr
- Trípode Libec
- Trípode Kogan
- Trípode MOZA
- Trípode Flycam
- Trípode Gravity
- Trípode Sirui
- Trípode Vinten
- Trípode Neewer
- Trípode Ravelli
- Trípode Fidlock
- Trípode Vanguard
- Trípode SmallRig
- Trípode FeiYu-Tech
- Trípode FeiyuTech
- Trípode Sky-Watcher
- Trípode Hohem
- Trípode MOVE'N SEE
- Trípode On Air
- Trípode Kaiser Fototechnik
- Trípode Slidekamera
- Trípode IOptron
- Trípode FLOWCINE
- Trípode SteadiCam
- Trípode Fat Gecko
- Trípode 3 Legged Thing
- Trípode FLM
- Trípode Peak Design
- Trípode Easyrig
- Trípode Robus
- Trípode Studio Assets
- Trípode Square Jellyfish
- Trípode Stalco
- Trípode Tiltall
- Trípode E-Image
Últimos Trípode Manuales
26 Octubre 2024
25 Octubre 2024
17 Octubre 2024
8 Octubre 2024
3 Octubre 2024
2 Octubre 2024
2 Octubre 2024
1 Octubre 2024
24 Septiembre 2024
22 Septiembre 2024