Hartke Pro 2200 Manual de Usario

Lee a continuación 📖 el manual en español para Hartke Pro 2200 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
2 x 12-inch plus CD Horn Aluminum Drive
Bass Enclosure
P R O F E S S I O N A L S E R I E S
2200 Introduction and Features
Congratulations on purchasing the 2200 bass enclosure by Hartke! The Hartke
PRO Series enclosures have been designed to provide serious bassists a seri
ous speaker system to articulately project their musical creativity. Excellent
tone with deep lows and crisp highs are the trademark characteristics of the
Pro Series cabinets thanks to the world-renowned Hartke Aluminum Drive units.
num cones, impregnated fabric surrounds, and matched convex dust covers al
mounted in a heavy-duty steel frames. Using heavy-duty plywood construction
covered in rugged carpet with recessed jack plate and ergonomic handle, the
2200 will provide reliable performance from gig to gig and venue to venue
In these pages, youʼll find a detailed description of the features of the-2200, as
well as a description of its front and rear panels, step-by-step instructions for its
setup and use and full specifications. Youʼll also find a warranty card enclosed—
please donʼt forget to fill it out and mail it in so that you can receive online
technical support and so we can send you updated information about these and
other Samson products in the future
We recommend you record your serial number in the space provided below for
future reference.
Serial number:
Date of purchase
Should your unit ever require servicing, a Return Authorization number (RA)
must be obtained before shipping your unit to Samson. Without this number
the unit will not be accepted. Please call Samson at 1-800-3SAMSON (1-800
372-6766) for a Return Authorization number prior to shipping your unit. Please
retain the original packing materials and if possible, return the unit in the origi
nal carton and packing materials
2200 Features
2 x 12-inch heavy-duty, Aluminum
Low Frequency drivers
1-inch titanium, high frequency com-
pression driver
3/4" Plywood construction
Two Tuned Front Ports
Perforated metal speaker gril
Recessed metal handles
Stacking corners
1/4-inch phone & Speakon input jacks
Covered in durable carpet
Connecting the 2200
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little abou
impedance. Impedance is the electronic load that the speaker puts on the power amplifie
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers are wired in "Paralle
the total impedance is cut in half and when two speakers are wire in “Series” the tota
impedance is the sum of the speakers individual impedance.
The
2200
impedance (many audio guys used the made up word “ohmage”, however the
correct term is impedance) is 4 Ohms. So, when two 2200ʼs are connected together in
parallel, the total impedance is 2 Ohms. The impedance of your speaker also has an
effect on your amplifier. In general, the lower the impedance, the more power your ampl
fier will put out.
IMPORTANT
There is a minimum safe impedance so be sure to check the manufacturerʼs
recommended impedance for your amplifier to avoid any damage to your amplifier or void
ing your warranty.
Connecting the 2200 to Your Amplifier
The 2200 connections are made via 1/4” phone jacks located on the rear panel jack-plate
Be sure to make your connection with un-shielded speaker cable. Connect the Amplifie
Output to the speaker Input on the 2200ʼs rear jackplate
Using the HIGH FREQUENCY switch
You can tailor the high frequency response of your 4200 by using the High Frequenc
control switch. This three-position switch allows you to set the output level of the high fre
quency compression driver to ON, OFF and PAD. In the ON position, the high frequency
compression driver is active and
producing brightness to help you cut
through the backline, or enhance snap-
ping and harmonics during solo pas-
sages. If your ideal sound is less bright
you can set the HIGH FREQUENCY
to the PAD position, which will reduce
the compression driver output by 3dB
If you are looking for a deeper tone, se
the HIGH FREQUENCY control switch
in the middle position and the compres
sion driver will be completely off
Using the EXTENSION Output
The 2200 provides both 1/4-inch and
Speakon connections. You can use
either connector to connect to your
amplifier head. Since both the 1/4-
inch phone and Speakon connectors
are wired in parallel, you can connect
additional speaker cabinets using eithe
connector as an extension output. Be
sure to read the section above on
impedance to insure a proper hook-up
with your amplifier.
Hartke Systems
Distri buted Exclusively by
Samson Technologies Corp.
Hicksv ille, New York 11802
MOD EL 2000
200 WAT TS
8
= 120 WA TTS
4
= 200 WA TTS
CAUTION
TO PREVENT SHOCK, DO NOT O PEN. NO USER SERVICE-
ABLE PARTS I NSIDE. REFER SERVICING TO Q UALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOIST URE.
ASSEMBLED IN R.O.K.
SERIAL NUMBER
115
~ AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V , 180W (115 V)
2.5A/250 V, 450W (230V)
SPEA KER OUT PUTS
88
ON OFF
HPF
EFF EC T
SENDRETUIRN

Especificaciones del producto

Marca: Hartke
Categoría: No categorizado
Modelo: Pro 2200

¿Necesitas ayuda?

Si necesitas ayuda con Hartke Pro 2200 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Hartke Manuales

No categorizado Manuales

Últimos No categorizado Manuales