Henry Engineering MultiPhones Guest Pod II Manual de Usario

Henry Engineering No categorizado MultiPhones Guest Pod II

Lee a continuación 📖 el manual en español para Henry Engineering MultiPhones Guest Pod II (2 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
MULTIPHONES GUEST POD II
HEADPHONE AMPLIFIER with TALENT CONTROL
DESCRIPTION
The MultiPhones Guest Pod II is an individual headphone listening station for use with the MultiPhones Distributed
Headphones System. It features a high performance headphone amplifier, plus two illuminated pushbuttons that
are typically used by talent for “Cough” and “Talkback” functions. When used with the MultiPhones Master unit,
power and audio are supplied by the Master. The Guest Pod can also be used as a “stand alone” headphone
listening station (without a MultiPhones Master unit) if other powering is provided. The Guest Pod includes a Level
control and both ¼” and 3.5mm headphone jacks.
INSTALLATION
The Guest Pod II is designed for tabletop, under-counter, or r tabletop use, install the in-cabinet installation. Fo
rubber “feet” on the bottom of the enclosure. Another option is to install two #8 screws in the tabletop, 3” apart, and
slide the unit onto the screw heads. For under-counter installation, open the Guest Pod enclosure by removing the
four corner screws from the bottom of the unit. Remove the top of the “clamshell” enclosure. Drill screw holes in the
top as necessary and screw the top to the underside of the countertop. Re-attach the lower section to the top with
the bottom screws.The Guest Pod II can also be mounted into cabinetry using the optional Cabinet Mounting Plate.
For use with MultiPhones Master unit: The Guest Pod(s) is connected to the MultiPhones Master unit using cat5
cabling. In most cases, unshielded cables can be used. WARNING! DO NOT USE “CROSSOVER” CABLES.
Connect up to 3 Guest Pods directly to the MultiPhones Master unit. Each Guest Pod has 2 RJ45 connectors,
which are wired in parallel. (Use either connector.) Additional Guest Pods can be “daisy chained” together in any
combination. The total number of Guest Pods connected to one MultiPhones Master should not exceed 12 units.
For use as a “stand alone” headphone listening station: For “stand alone” use, the Guest Pod requires a
power source. Henry Engineering’s transformer may be used. The PowerPod will PowerPod or any 9-12 volt AC
power up to 12 Guest Pods. If a 12V AC transformer is used, each Guest Pod will require about 50 mA.
Two ¼” TRS input jacks on the rear panel accept stereo balanced audio at about 0 dBu.
Wire the inputs as follows: Tip = High; Ring = Low; Sleeve = Ground.
Multiple Guest Pods can be used by “daisy chaining” them together with cat5 cabling. Both power and audio will be
distributed to all Guest Pods via the cat5 cables. (To distribute power but not audio, remove R1, R19, R21, & R22
from each Guest Pod unit in the system.)
Talent control buttons: The two talent buttons (Cough and Talkback) must be wired to the Control RJ45
connector by the user. Any pin-out can be accommodated. Install wires between the switch terminals and the PC
board pads labeled , which correspond to the pins on the Control RJ45 connector. Be sure to install a W1 thru W8
resistor in series with the LED in each switch according to the tally supply voltage being used. (12vdc = 2K ohms.)
See the schematic on the reverse side for switch terminal details.
OPERATION
The Guest Pod II is simple in its operation. The LEVEL controls adjust the audio level to the PHONES jacks. Do
not use both jacks at the same time. Use headphones with an impedance between 24 and 600 ohms.
Do not use older “8-ohm” headphones. Excessive listening levels can cause permanent hearing damage!
SPECIFICATIONS
INPUT From MultiPhones Master unit or
¼” TRS jacks, 2X, 0 dBu, balanced 20K
OUTPUT For 24 – 600 ohm headphones, ¼” and 3.5mm jacks
FREQUENCY RESPONSE 5 Hz – 20 kHz, +/- 0.25 dB
DISTORTION .005% typical
NOISE -80 dBm typical
POWER INPUT Supplied by MultiPhones Master unit, PowerPod,
or 9-12 VAC transformer, 50mA per unit
PHYSICAL DIMEN 5.75”w X 1.75”h X 6.0”d, 1 LB
MOUNTING PLATE 5.5”w X 1.5”h, 6.0” behind panel; cutout: 4.5”w X 1.0”h (optional)
Specifications subject to change without notice. Rev. 1/19
HENRY ENGINEERING
PO Box 3796
Seal Beach, CA 90740
Tel: 562.493.3589
www.henryeng.com
TM

Especificaciones del producto

Marca: Henry Engineering
Categoría: No categorizado
Modelo: MultiPhones Guest Pod II

¿Necesitas ayuda?

Si necesitas ayuda con Henry Engineering MultiPhones Guest Pod II haz una pregunta a continuación y otros usuarios te responderán


No categorizado Henry Engineering Manuales

Henry Engineering

Henry Engineering Mike Alert Manual de Usario

18 Septiembre 2024
Henry Engineering

Henry Engineering MultiPort Manual de Usario

18 Septiembre 2024
Henry Engineering

Henry Engineering USB Matchbox II Manual de Usario

18 Septiembre 2024
Henry Engineering

Henry Engineering MultiPhones Guest Pod II Manual de Usario

18 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024