Hitachi C10FCG Manual de Usario
Hitachi
máquina de aserrar
C10FCG
Lee a continuación 📖 el manual en español para Hitachi C10FCG (49 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/49
DOUBLE INSULATION
DOUBLE ISOLATION
AISLAMIENTO DOBLE
Model
Modèle
Modelo
C 10FCG
Compound Miter Saw
Scie à onglets combinée
Sierra ingletadora
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this
manual BEFORE operating the power tool. Please keep this manual available for other users and owners
before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort ou de
sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit. Prière
de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce mode d’emploi
à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode
d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar en lesiones
de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y comprenda este
manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para que puedan leerlo otras
personas antes de utilizar la herramienta eléctrica. Este manual debe ser guardado en un lugar seguro.
English PAGE PAGE
Français PAGE PAGE
Español PÁGINA PÁGINA
CONTENTS
TABLE DES MATIERES
ÍNDICE
SPÉCIFICATIONS ......................................................21
ACCESSOIRES .......................................................... 21
APPLICATIONS ..........................................................22
PRÉPARATION AVANT L’UTILISATION .....................22
AVANT L’UTILISATION ...............................................23
AVANT LA COUPE ..................................................... 23
APPLICATIONS PRATIQUES .....................................24
INSTALLATION ET RETRAIT DE LA LAME ...............28
ENTRETIEN ET INSPECTION ...................................28
SERVICE APRÈS-VENTE ET RÉPARATIONS ...........29
GUIDE DE DÉPANNAGE ............................................30
LISTE DES PIECES ....................................................46
INFORMATIONS IMPORTANTES DE SÉCURITÉ ..... 17
SIGNIFICATION DES MOTS D’AVERTISSEMENT .... 17
SECURITE ..................................................................... 17
CONSIGNES DE SECURITE RELATIVES AUX
OUTILS ÉLECTRIQUES ...................................... 17
PIECES DE RECHANGE ............................................ 18
UTILISER LE CORDON DE
RALLONGE APPROPRIÉ .................................... 19
DOUBLE ISOLATION POUR UN
FONCTIONNEMENT PLUS SUR......................... 19
UTILISATION ET ENTRETIEN ......................................20
NOM DES PIÈCES .....................................................20
APPLICATIONS ............................................................7
PREPARATION BEFORE OPERATION .......................7
BEFORE USING ...........................................................8
BEFORE CUTTING ......................................................9
PRACTICAL APPLICATIONS .....................................10
SAW BLADE MOUNTING AND
DISMOUNTING ................................................... 13
MAINTENANCE AND INSPECTION ..........................14
SERVICE AND REPAIRS............................................15
TROUBLESHOOTING GUIDE ................................... 16
PARTS LIST ................................................................46
IMPORTANT SAFETY INFORMATION ........................3
MEANINGS OF SIGNAL WORDS ................................3
SAFETY ............................................................................3
IMPORTANT SAFETY INSTRUCTIONS FOR
USING ALL POWER TOOLS .................................3
REPLACEMENT PARTS ..............................................4
USE PROPER EXTENSION CORD .............................4
DOUBLE INSULATION FOR SAFER OPERATION ......5
OPERATION AND MAINTENANCE ................................5
NAME OF PARTS .........................................................5
SPECIFICATIONS ........................................................6
ACCESSORIES ............................................................7
ESPECIFICACIONES .................................................35
ACCESORIOS ............................................................ 35
APLICACIONES..........................................................36
PREPARATIVOS PREVIOS A LA OPERACIÓN .........36
ANTES DE LA UTILIZACIÓN .....................................37
ANTES DEL CORTE ...................................................37
APLICACIONES PRÁCTICAS ....................................38
MONTAJE Y DESMONTAJE DE LA
HOJA DE SIERRA ...............................................42
MANTENIMIENTO E INSPECCIÓN ...........................43
SERVICIO Y REPARACIONES ...................................44
GUIA DE IDENTIFICACION DE PROBLEMAS ...........45
LISTA DE PIEZAS .......................................................46
INFORMACIÓN IMPORTANTE SOBRE
SEGURIDAD ........................................................ 31
SIGNIFICADO DE LAS PALABRAS DE
SEÑALIZACIÓN ...................................................31
SEGURIDAD .................................................................. 31
NORMAS DE SEGURIDAD PARA LAS
HERRAMIENTAS ELÉCTRICAS ..........................31
PIEZAS DE REEMPLAZO .......................................... 32
UTILICE EL CABLE PROLONGADOR
ADECUADO .........................................................33
AISLAMIENTO DOBLE PARA OFRECER UNA
OPERACIÓN MÁS SEGURA ...............................33
OPERACIÓN Y MANTENIMIENTO ...............................34
NOMENCLATURA DE PARTES .................................34
3
English
IMPORTANT SAFETY INFORMATION
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power
tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can
often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance
instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power tool and in this Instruction Manual.
Never use this power tool in a manner that has not been specifi cally recommended by HITACHI.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information.
SAFETY
IMPORTANT SAFETY INSTRUCTIONS FOR USING ALL POWER TOOLS
READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS MANUAL BEFORE OPERATING OR
MAINTAINING THIS TOOL:
WARNING:
When using this electric tool, take all necessary precautions to minimize the risk of electric shock or other personal injury.
In particular, always comply with the following safety rules:
1. ALWAYS KEEP GUARDS IN PLACE and in working order.
2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE
STARTING TOOL. Always confi rm that all keys and adjusting wrenches
have been removed from the tool before it is turned on.
3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering
the work areas and work benches.
4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the
power tool in damp or wet places and never expose it to rain. Always keep
the work area well lighted.
5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE
WORK AREA. Keep all people (especially children) away from the work
area. Always unplug unattended tools and keep the work place tamper-
proof by installing locks on the doors and on the master switches.
6. NEVER FORCE THE TOOL. It will do the job better and more safely if it
is operated at the rate for which it was designed.
7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment
to do a job for which it was not designed.
8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE
TOOL. Never wear loose clothing, gloves, neckties, rings, bracelets or
other jewelry which may get caught in the moving parts. Always wear
non-slip footwear, preferably with steel toes. Wear protective hair covering
to contain long hair.
9. ALWAYS WEAR EYE PROTECTION WITH SIDE SHIELDS THAT
MEETS THE REQUIREMENTS OF ANSI STANDARD Z87.1 WHEN
WORKING WITH THE TOOL TO PREVENT EYE INJURY. Ordinary
eyeglasses do not provide adequate protection because they do not
contain impact resistant safety glass. Also, use a face mask for additional
safety and wear a dust mask if the cutting operation produces dust.
10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE.
Use clamps or a vise to hold the workpiece in place. It is safer than using
your hand and it frees both hands to operate the tool.
11. NEVER OVERREACH. Always keep proper footing and balance when
working with the tool.
12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and
clean for the best and safest performance. Always follow instructions for
lubricating the tool and for changing accessories.
13. ALWAYS DISCONNECT THE TOOL before servicing and before
changing blades or other accessories.
14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN
THE TOOL. Always confi rm that the switch is in the OFF position before
inserting the power plug into the receptacle.
15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN
OPERATING THIS TOOL. Consult this instruction manual for descriptions
of recommended accessories. To avoid personal injuries, use only
recommended accessories in conjunction with this tool.
16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the
tool and by not risking unintentional contact with the saw blade.
17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL.
Always check the guard and all other components for damage before
using the tool to assure that they will function properly. Check all moving
parts for proper alignment, freedom from binding and other conditions
that might aff ect proper operation. Always repair or replace any damaged
guards or other damaged components before using the tool.
18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE
BEFORE USING THE TOOL. Always feed work into the tool against the
rotation direction of the blade in order to prevent possible injury.
19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN
POWER OFF. Do not leave tool until it comes to a complete stop. Always
turn the power off when the tool is not in use. Always unplug the power
cord when the tool is not in use.
20. This tool was not designed to be used for mass-production applications
and should not be used in mass-production environments.
21. When servicing this tool, use only authorized replacement parts.
22. Apply 120 volts AC only to this tool. Applying the wrong voltage or applying
DC power can cause the POWER TOOL to operate improperly and cause
serious personal injury or damage to the tool.
23. Never raise the saw blade from the workpiece until it has fi rst come to a
complete stop.
24. Always use outboard stands to provide support for long workpieces that
overhang the table of the slide compound miter saw.
25. Always return the carriage to the full rear position after each crosscut
operation in order to reduce the risk of injury.
26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment
has a polarized plug (one blade is wider than the other). This plug will fi t
in a polarized outlet only one way. If the plug does not fi t fully in the outlet,
reverse the plug. If it still does not fi t, contact a qualifi ed electrician to
install the proper outlet. Do not change the plug in any way.
Specifi c Safety Rules for Use of this Power Tool
WARNING:
The following specifi c operating instructions must be observed
when using this POWER TOOL in order to avoid injury:
DO’s
ALWAYS OBSERVE THE FOLLOWING RULES TO
ASSURE SAFE USE OF THIS TOOL:
1. Review this Manual and familiarize yourself with the safety rules and
operating instructions for this POWER TOOL before attempting to use it.
2. Remove all packing materials attached or connected to the tool before
attempting to operate it.
3. Always confi rm that the POWER TOOL is clean before using it.
4. Always wear snug-fi tting clothing, non-skid footwear (preferably with steel
toes) and eye protection when operating the POWER TOOL.
Especificaciones del producto
| Marca: | Hitachi |
| Categoría: | máquina de aserrar |
| Modelo: | C10FCG |
¿Necesitas ayuda?
Si necesitas ayuda con Hitachi C10FCG haz una pregunta a continuación y otros usuarios te responderán
máquina de aserrar Hitachi Manuales
10 Octubre 2024
26 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
15 Septiembre 2024
13 Septiembre 2024
5 Septiembre 2024
5 Septiembre 2024
5 Septiembre 2024
16 Agosto 2024
máquina de aserrar Manuales
- máquina de aserrar Bosch
- máquina de aserrar AEG
- máquina de aserrar DeWalt
- máquina de aserrar Ford
- máquina de aserrar Silverline
- máquina de aserrar Brennenstuhl
- máquina de aserrar Ferm
- máquina de aserrar Clarke
- máquina de aserrar Ozito
- máquina de aserrar Gude
- máquina de aserrar Makita
- máquina de aserrar Draper
- máquina de aserrar Black And Decker
- máquina de aserrar Vonroc
- máquina de aserrar Remington
- máquina de aserrar ACG
- máquina de aserrar Stanley
- máquina de aserrar Skil
- máquina de aserrar Hyundai
- máquina de aserrar Hilti
- máquina de aserrar Ryobi
- máquina de aserrar Florabest
- máquina de aserrar Festool
- máquina de aserrar Metabo
- máquina de aserrar Parkside
- máquina de aserrar Worx
- máquina de aserrar Meec Tools
- máquina de aserrar Milwaukee
- máquina de aserrar Hikoki
- máquina de aserrar Sun Joe
- máquina de aserrar Dremel
- máquina de aserrar Sovereign
- máquina de aserrar Tacklife
- máquina de aserrar Hazet
- máquina de aserrar Einhell
- máquina de aserrar Baumr-AG
- máquina de aserrar Yard Force
- máquina de aserrar Ferrex
- máquina de aserrar Husqvarna
- máquina de aserrar Maktec
- máquina de aserrar Craftsman
- máquina de aserrar Power Craft
- máquina de aserrar Powerplus
- máquina de aserrar Stiga
- máquina de aserrar Porter-Cable
- máquina de aserrar Cotech
- máquina de aserrar Genesis
- máquina de aserrar Trotec
- máquina de aserrar Troy-Bilt
- máquina de aserrar Cobra
- máquina de aserrar Texas
- máquina de aserrar Spear & Jackson
- máquina de aserrar Scheppach
- máquina de aserrar Atika
- máquina de aserrar McCulloch
- máquina de aserrar Sterwins
- máquina de aserrar Matrix
- máquina de aserrar Stihl
- máquina de aserrar Bavaria
- máquina de aserrar Dolmar
- máquina de aserrar Shindaiwa
- máquina de aserrar Flex
- máquina de aserrar Prime3
- máquina de aserrar Zipper
- máquina de aserrar Mafell
- máquina de aserrar Greenworks
- máquina de aserrar Fieldmann
- máquina de aserrar Max
- máquina de aserrar IKRA
- máquina de aserrar Truper
- máquina de aserrar Masport
- máquina de aserrar Grizzly
- máquina de aserrar Solo
- máquina de aserrar Cocraft
- máquina de aserrar MTM
- máquina de aserrar Maruyama
- máquina de aserrar Herkules
- máquina de aserrar Meister Craft
- máquina de aserrar Toolcraft
- máquina de aserrar RIDGID
- máquina de aserrar Batavia
- máquina de aserrar Proxxon
- máquina de aserrar Gardenline
- máquina de aserrar Holzmann
- máquina de aserrar Fein
- máquina de aserrar Oregon Scientific
- máquina de aserrar Elu
- máquina de aserrar Max Bahr
- máquina de aserrar Plantiflor
- máquina de aserrar Goon
- máquina de aserrar Triton
- máquina de aserrar BGU
- máquina de aserrar Wolfcraft
- máquina de aserrar Dedra
- máquina de aserrar Verto
- máquina de aserrar Anova
- máquina de aserrar Challenge Xtreme
- máquina de aserrar Global
- máquina de aserrar Rikon
- máquina de aserrar Elektra Beckum
- máquina de aserrar Duro Pro
- máquina de aserrar Toolson
- máquina de aserrar Toledo
- máquina de aserrar Jonsered
- máquina de aserrar MSW
- máquina de aserrar Royal Catering
- máquina de aserrar Robust
- máquina de aserrar Ultranatura
- máquina de aserrar FIXIT
- máquina de aserrar Einhell Bavaria
- máquina de aserrar Ergotools Pattfield
- máquina de aserrar MyTool
- máquina de aserrar McKenzie
- máquina de aserrar Proviel
- máquina de aserrar Morrison
- máquina de aserrar Garland
- máquina de aserrar Bavaria By Einhell
- máquina de aserrar Donau Elektronik
- máquina de aserrar Chicago Pneumatic
- máquina de aserrar Rona
- máquina de aserrar Bestgreen
- máquina de aserrar CMI
- máquina de aserrar MacAllister
- máquina de aserrar TAURUS Titanium
- máquina de aserrar Maxbear
- máquina de aserrar Evolution
- máquina de aserrar Extralink
- máquina de aserrar Yellow Garden Line
- máquina de aserrar Stalco
Últimos máquina de aserrar Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
26 Octubre 2024
26 Octubre 2024
22 Octubre 2024