HQ EL-PIR80 Manual de Usario

HQ Alivio EL-PIR80

Lee a continuación 📖 el manual en español para HQ EL-PIR80 (66 páginas) en la categoría Alivio. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/66
EL-PIR80
Radar sensor light
1
The sensor light has an active motion detector, the integrated HF sensor emits high-
frequency electro-magnetic wave (5.8GHz) and receives their echo. The sensor
detects the change in echo from even the slightest movement in the light’s detection
zone. A microprocessor then triggers the “switch light ONcommand. Detection is
possible through doors, panes of glass or thin walls.
Detection zones for ceiling mounting
1) Minimum reach 1m dia.
2) Maximum reach 8m dia.
Detection zones for wall mounting
3) Minimum reach 1m dia.
4) Maximum reach 8m dia.
Important: persons or objects moving towards the light are detected best!
Installation procedures
1. Take down the glass shade by turning it anti-clockwise (see g.1)
2. Hold base against the wall and mark drill holes, paying attention to any existing
wiring in the wall;
3. Drill the holes, insert wall plugs (6mm dia);
4. Put the power wire and load wire through the base holes;
5. Screw the base into place (see g. 2);
6. Connect the mains power supply and the load wire to the connection terminal
according to connection-wire mark.
7. Adjust knob to setting;
8. Fit glass shade and turn it clockwise (see g. 3).
2
Technical specications
Wattage: 60W/E27
Power supply: 220-240V~, 50/60Hz
Installation sit: indoors, wall/ceiling mounting
HF system: 5.8GHz CW radar, ISM band
Transmission power: <10mW
Detection angle: 360°, 160°
Reach: 1-8m (dia.), adjustable
Time setting: 5sec to 15min
Light control: 2~2000LUX
Power consumption: approx.0.9W
Connection illumination
connect N, L with power;
Reach setting (sensitivity)
Reach is the term used to describe the diameter of the more or less
circular detection zone produced on the ground after mounting the
sensorlight at a height of 2.5m, turn the reach control fully anticlockwise
to select minimum reach (approx.1 m dia), and fully clockwise to select
maximum reach (approx. 8m dia).
Time setting
The light can be set to stay ON for any period of time between approx.
5sec(turn fully anticlockwise) and a maximum of 15min(turn fully
clockwise). Any movement detected before this time elapse will re-start
the timer. It is recommended to select the shortest time for adjusting the
detection zone and for performing the walk test.
NOTE: after the light switches OFF, it takes approx. 1sec before it is able to start
detecting movement again. The light will only switch on in response to movement
once this period has elapsed.
Light-control setting
The chosen light response threshold can be innitely from approx. 2-
2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at
about 2 lux. Turn it fully clockwise to select daylight operation at about
2000lux. The knob must be turned fully clockwise when adjusting the
detection zone and performing the walk test in daylight.
SENS TIME LUX
SENS
TIME
LUX

Especificaciones del producto

Marca: HQ
Categoría: Alivio
Modelo: EL-PIR80

¿Necesitas ayuda?

Si necesitas ayuda con HQ EL-PIR80 haz una pregunta a continuación y otros usuarios te responderán




Alivio HQ Manuales

HQ

HQ 090B Manual de Usario

22 Septiembre 2024

Alivio Manuales

Últimos Alivio Manuales