Indesit BAN 12 NF S (UK) (0) Manual de Usario

Indesit Combinaciones frigorífico-congelador BAN 12 NF S (UK) (0)

Lee a continuación 📖 el manual en español para Indesit BAN 12 NF S (UK) (0) (12 páginas) en la categoría Combinaciones frigorífico-congelador. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

REFRIGERATOR/FREEZER COMBINATION

Contents

Installation, 2

Positioning and connection

Reversible doors

Description of the appliance, 4

Overall view

Accessories, 5

Start-up and use, 6-7

Starting the appliance

Chiller system

Using the refrigerator to its full potential

Using the freezer to its full potential

Maintenance and care, 8

Switching the appliance off

Cleaning the appliance

Avoiding mould and unpleasant odours

Defrosting the appliance

Replacing the light bulb

Precautions and tips, 9

General safety

Disposal

Respecting and conserving the environment

Troubleshooting, 10

Assistance, 11

Operating Instructions

BAN 12 NF S

English

Installation

! Before placing your new appliance into operation please

read these operating instructions carefully. They contain

important information for safe use, for installation and for

care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free

room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of

the appliance and any furniture above it, and at least 5

cm between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat

(direct sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the

appliance and the wall behind it, fit the spacers supplied

in the installation kit, following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the

refrigerator by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully place it

vertically and wait at least 3 hours before connecting it to

the electricity mains. Before inserting the plug into the

electrical socket ensure the following:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located on

the bottom left side of the fridge (e.g. 150 W).

• The voltage must be in the range between the values

indicated on the data plate located on the bottom left

side (e.g. 220-240V).

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it (

see Assistance

). Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

Connection of the water supply

To carry this out, use the kit provided which contains all the

necessary elements for connection to the water supply.

To improve the performance of the Aqua Care, we

recommend that you fit a tap with a filter on the pipe for

the connection to the water system: in this way it will be

possible to manually interrupt the water supply during

long periods in which Aqua Care is not used.

! The water pressure inside the water system must be

between 0.8 bar and 8 bar.

! The appliance must only be connected to a water

supply suitable for drinking.

Your appliance is supplied with a 13amp fused plug that

can be plugged into a 13amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved

fuse to BS 1362 should always be used and the fuse

cover re-fitted.

If the fuse cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a longer cable

or to re-route the mains cable through partitions, units

etc. please ensure that either:

- The plug is replaced by a fused 13amp re-

wireable plug bearing the BSI mark of approval.

- The mains cable is wired directly into a 13amp

cable outlet, controlled by a switch (in compliance

with BS 5733) which is accessible without moving

the appliance.

Disposing of the plug

Cut off and dispose of the supplied plug if it does not fit

your socket. The cable should be cut as close as

possible to the moulded plug.

Remove the fuse.

Reversible doors

∅ 3mm

WARNING:

To avoid a shock hazard do not insert the discarded

plug into a socket anywhere else.

Fitting a new plug

IMPORTANT

WIRES IN THE MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE...

Green and Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

- Connect Green and Yellow wire to terminal marked

'E' or or coloured Green and Yellow.

- Connect Brown wire to terminal marked 'L' or

coloured red or brown.

- Connect Blue wire to terminal marked 'N' or

coloured Black or Blue.

If a 13amp plug (BS 1363) is used it must be

fitted with a 13amp fuse.

If you are in any doubt about the electrical

supply to your machine, consult a qualified

electrician before use.

CE Marking certifies that this appliance conforms to

the following EEC directives :

Low Voltage Equipment - 73/23/EEC & 93/68 EEC

Electromagnetic Compatibility 89/336/EEC, 92/31/EEC

& 93/68/EEC

Especificaciones del producto

Marca:	Indesit
Categoría:	Combinaciones frigorífico-congelador
Modelo:	BAN 12 NF S (UK) (0)

¿Necesitas ayuda?

Si necesitas ayuda con Indesit BAN 12 NF S (UK) (0) haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Combinaciones frigorífico-congelador Indesit Manuales

Indesit TN 5 FNF (TK) Manual de Usario

18 Octubre 2024

Indesit IBD 5515 W 1 Manual de Usario

18 Octubre 2024

Indesit BAAN 40 FNF NX D Manual de Usario

16 Octubre 2024

Indesit BAN 12 NF S (UK) (0) Manual de Usario

12 Octubre 2024

Indesit BIAA 13 SI WD UK Manual de Usario

10 Octubre 2024

Indesit INFC8 TO22K Manual de Usario

8 Octubre 2024

Indesit R 2750 BI Manual de Usario

8 Octubre 2024

Indesit LD85 F1 K.1 Manual de Usario

24 Julio 2024

Indesit RA 34 Manual de Usario

24 Julio 2024

Indesit I55TM 4110 X Manual de Usario

23 Julio 2024

Combinaciones frigorífico-congelador Manuales

Últimos Combinaciones frigorífico-congelador Manuales

Amana ABB1927DEB Manual de Usario

21 Octubre 2024

LG GR-H2273KTG Manual de Usario

21 Octubre 2024

Samsung RT45K5000WW Manual de Usario

21 Octubre 2024

GE TBX16ZPKRWH Manual de Usario

21 Octubre 2024

Hisense RT417N4DW1 Manual de Usario

20 Octubre 2024

Viking FDSB5423 Manual de Usario

20 Octubre 2024

Gorenje RCI4181AWV Manual de Usario

20 Octubre 2024

BEKO BCSA285K2S Manual de Usario

20 Octubre 2024

GE TPX24PBBBWW Manual de Usario

19 Octubre 2024

Teka NFL 342 EU Manual de Usario

19 Octubre 2024