Inovonics EN4216MR Manual de Usario

Inovonics receptor EN4216MR

Lee a continuación 📖 el manual en español para Inovonics EN4216MR (5 páginas) en la categoría receptor. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/5

2/3/20 357-05637-02 Rev A © Inovonics, 2020 - www.inovonics.com

EN4216MR 16 Zone Multi-Condition

Receiver with Relay Outputs

Installation and Operation Manual

1 Overview

The EN4216MR receiver allows you to add up to 16 transmitters and five

outputs to any application, and includes a housing tamper for increased

tamper security.

The following add-on receivers are available from Inovonics:

* At least one relay must be used for faults to ensure the system is

supervised. More than one relay may be used, but that will deduct from the

number of alarm output relays.

1.1 Installing an Inovonics Security System

An EchoStream survey kit must be used to establish a UL system. The

EchoStream survey kit measures the signal strength of high-power

repeater and sensor messages to help optimize your EchoStream system.

Figure 1 Sample EchoStream system

The EchoStream survey kit provides you with two signal strength

measurements: signal level and signal margin.

Signal level

The signal level is the measurement of the overall decibel level of the

message.

Signal margin

The signal margin is the measurement of the decibel level of the message,

minus the decibel level of any interfering signals. Inovonics Wireless

equipment should be placed within a facility such that all end-devices

produce signal margin readings of at least 4 decibels.

Both the signal level and signal margin are measured in decibels. Because

signal strength and signal margin are measured on a logarithmic scale, the

difference between a decibel level of 3 (Weak) and a decibel level of 4

(Good) is a much larger difference than it would be on a linear scale.

Note: For more information about the EchoStream survey kit, see the

EN7017 Survey Kit and App Installation and Site Survey Instructions.

Caution: The EchoStream system should be tested regularly to ensure

operation. To test: place the system in test mode, activate an end device,

and ensure an appropriate response.

1.2 RF Signal Propagation

While wood, drywall and glass usually let the RF signals pass, some

materials may inhibit or attenuate radio frequency (RF) signal propagation

by blocking, reflecting, deflecting or absorbing RF signals.

Consider anything between transmitters and repeaters and/or the receiver.

Is there concrete and steel construction? Are there earthen berms or hills?

Are there a lot of trees? Devices should be mounted such that they are

least affected by these elements.

For best results, transmitters and repeaters should be mounted at the

optimal height to achieve line of sight to repeaters and/or the receiver.

Usually this means they will be mounted as high as possible.

Following are some typical obstacles to RF signal propagation:

1.3 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical

services:

Receiver Alarm Output

Relays Fault Relays Transmitters

Supported

EN4204R 4 1 4

EN4216MR 5 1* 16

EN4232MR 11 1* 32

Material Affect Recommendation

Metal construction,

including ductwork;

pipes; studs; stucco,

plaster or concrete with

wire mesh; satellite

dishes, metal-lined

rooms such as walk-in

coolers or freezers;

metal siding, safes, etc.

Can reflect,

absorb and/or

disrupt RF

signals.

Perform a site survey

using an Inovonics

wireless survey kit to

verify the RF signal is

acceptable, and, when

necessary, to

determine where to

locate repeaters.

Completely enclosed

metal boxes/enclosures.

Can restrict RF

signals.

Solar panels, cinder

block walls, windows

with built-in solar tinting.

Can absorb and/

or reflect RF

signals.

Vegetation. Can attenuate

RF signals. The

RF environment

can alter as

trees shed or

sprout leaves.

Add repeaters as

issues arise.

Automobile and truck

traffic.

Can disrupt RF

signals.

Mount Inovonics

devices at a height

sufficient to achieve

line of sight above

traffic.

For product and installation videos visit us at

www.inovonics.com/videos or use the QR

code below.

2/3/20 357-05637-02 Rev A © Inovonics, 2020 - www.inovonics.com 2

• E-mail: support@inovonics.com.

• Phone: (800) 782-2709; (303) 939-9336.

1.4 EN4216MR Front Panel

Figure 2 Receiver front panel

Output LED: Lights when any transmitter output is active.

Fault LED: Lights when any transmitter is sending a fault condition.

Power LED: Lit when receiving power.

LCD Display: Shows status, event log and programming information.

Decode LED: Flashes when any recognizable transmission is received.

This LED is only visible when the cover is removed.

Up button: Scrolls the display up.

Down button: Scrolls the display down.

Back button: Returns display to the previous menu, or when pressed in the

main menu options, returns the unit to normal operating mode. When

entering information in the display, returns to the last character entered.

Enter button: Selects the currently displayed menu item. If in normal

operating mode, sets the unit to menu mode.

Reset button: Clears the current status for all points and resets all outputs

and LEDs. Records a receiver reset entry in the event log and resets the

supervision window timers. This button is only accessible when the cover is

removed.

1.5 EN4216MR Internal Components

Figure 3 EN4216MR internal components

1.6 What’s in the Carton

• Two drywall anchors.

• Two mounting screws.

• Two pieces of double-sided mounting tape.

• One selection jumper.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be maintained by professional

security technicians.

• Products are tested for indoor use.

• Do not mount wireless smoke detectors, co detectors, initiating device

transmitters or repeaters to removable surfaces, such as ceiling tiles.

• All products should be manually tested weekly.

• The EN4216MR must be installed within 30 m (98.5 ft) of control unit.

• Low power transmitters shall be limited to a single initiating device.

2.2 Power Cabling

Caution: Incorrect connections may cause damage to the unit.

Before beginning startup, you will need to connect power to the receiver. To

connect power to the receiver:

1. Use a small screwdriver to press the housing release tabs on the top or

bottom of the receiver; separate the housing.

2. Connect power cabling to the Vs (+) and GND (-) connections.

• Power source should be 11-14 VDC. Power supply must be

unswitched, uninterrupted, and regulated.

• Use 18 - 22 gauge wire for all cabling, and ensure torque on the screw

terminals does not exceed 7 inch-pounds.

2.3 Select the Frequency Band

EchoStream products are able to use a range of radio frequencies, and are

shipped from Inovonics set for your geographic area.

• The jumper will be set on the two pins marked NZ to set the frequency

range to 921-928 MHz for New Zealand.

• The jumper will be set on the two pins marked AU to set the frequency

range to 915-928 MHz for Australia.

• The jumper will be removed to set the frequency band to 902-928

MHz for North America.

1. Ensure the frequency band is set for your geographic are.

2. If the frequency band is not set for your geographic area, place a

selection jumper on the appropriate frequency band selection pins to

select Australia or New Zealand, or remove it for North America.

Note: Only devices set for use in North America are configured for UL

installations.

3. If you have changed the frequency band and the device is powered on,

press the reset button to complete configuration.

2.4 Connect Input/Output Cabling

4. Connect cabling to the receiver power loss output. Must be configured

for UL installations.

• The receiver power loss output is a normally closed (N/C) open

collector output that opens when the receiver loses power.

5. Connect cabling to the tamper output. Must be configured for UL

installations.

• The tamper output is a normally open (N/O) open collector output that

reports receiver case tamper to an external device.

6. Connect cabling to the jam output. Must be configured for UL

installations.

• The jam output is a normally closed (N/C) open collector output that

opens when noise thresholds on all receive channels remain above a

predetermined value for 10 seconds. The jam output is set to the

follower output type.

7. Connect a momentary switch to the reset input and ground (Figure 4,

“EN4216MR terminals”). Must be configured for UL installations.

• The reset input circuit permits installation of a remote momentary

normally open (N/O) switch to clear faults, unlatch outputs, and reset

the receiver to a normal state.

8. Connect cabling to the output terminals. Must be configured for UL

installations.

• The EN4216MR provides six Form-C relays.

Figure 4 EN4216MR terminals

A B COutput LED Fault LED Power LED

D E FLCD display Up button Down button

G HBack button Enter button

AHousing release

tabs

BPower

connections

COperation LEDs

D ERelay outputs Tamper output FReceiver power loss output

G H IJam output Reset input Frequency band selection

pins

J KReset button Decode LED

G H

A A

Jam output

Ground

Tamper output

Reset input

Receiver

power loss

output

Caution:

Incorrect

connections

may cause

damage to the

unit

COM 1

COM 2

COM 3

COM 4

COM 5

COM 6

2/3/20 357-05637-02 Rev A © Inovonics, 2020 - www.inovonics.com 3

2.5 Mount the Receiver

Caution: Mount the receiver in a location removed from metal. Metal

objects (duct work, wire mesh screens, boxes) will reduce RF range.

Note: For UL listed systems containing a UL hold-up switch, the

EN4216MR must be located within three feet of a system keypad in a

location out of sight from the protected premise.

9. Use the provided anchors and screws to mount the receiver in a

location accessible for future maintenance.

10. Perform a walk test, activating each transmitter assigned to the receiver

and ensuring a good signal.

3 Point Setup and Registration

Each transmitter must setup and registered to a point. Once registered, the

transmitters alarm(s) will be mapped to the appropriate alarm output(s).

Following are the transmitters supported by the EN4216MR:

Note: Contact Inovonics for a list of other compatible devices..

3.1 Program a Point

1. From the EN4216MR start screen, press the enter button to access the

receiver’s three main menu options.

2. Use the up and down buttons to navigate to the install & service menu;

press the enter button.

3. Enter your password to access the install & service menus.

4. Following the instructions in section 4.5.1, “Setup Point” on page 4.

4 EN4216MR 16 Zone Multi-Condition Receiver with

Relay Outputs Operation and Point Setup Screens

4.1 Menu Tree

POINT STATUS, see 4.3, “Point Status” on page 3.

EVENT LOG, see 4.4, “Event Log” on page 3.

INSTALL & SERVICE, 4.5, “Install & Service” on page 4.

SETUP POINT, see 4.5.1, “Setup Point” on page 4.

POINT #

SUPERVISION TIME

SECURITY/REPEATER

ALARM INPUTS

ALARM OUT

ALARM OUTPUT TYPE

INACTIVE O /TUT YPE

TAMPER OUT/TYPE

LOW BATTERY OUT/TYPE

TEXT

page 4.

DELETE POINT, see 4.5.3, “Delete Point” on page 4.

SIGNAL STRENGTH, see 4.5.4, “Signal Strength” on page 5.

CHANGE PASSWORD, see 4.5.5, “Change Password” on page 5.

FACTORY CONFIG, see 4.5.6, “Factory Config” on page 5.

4.2 EN4216MR Start Screen

The EN4216MR start screen displays alarm and fault information on the

LCD display. Points in alarm are displayed as “Alarm”, with the point

number following. If more than one point is in alarm, the display scrolls

through each point. If a point has more than one alarm, the display scrolls

through each alarm. Fault conditions are indicated by “Fault” in the LCD

display if there is no alarm already displayed, and point numbers are not

displayed.

Alarms and faults will only display briefly when the alarm or fault is first

received, and then the start screen will return to a ready condition. For

detailed alarm and fault information, see section 4.3, “Point Status” on

page 3.

4.3 Point Status

The point status menu allows you to view detailed alarm and fault

information. Point status information is available without entering a

password.

To access the point status menu:

1. From the EN4216MR start screen, press the enter button to access the

receiver’s three main menus. “Point Status” displays.

2. Press the enter to display point status details.

3. Use the up/down buttons to scroll through the points; press the enter

button again to view the outputs the displayed conditions are mapped

to.

• Point status flags are defined as follows: A = Alarm (transmitter only);

T = Tamper; B = Low Battery; L = AC loss (repeater only); I = Inactive.

Note: If “--” displays, the displayed condition has been mapped to a null

output.

4.4 Event Log

The event log displays the last 50 events that have occurred, whether they

be alarms, or tamper or inactive faults. Event log information is available

without a password.

1. From the EN4216MR start screen, press enter.

2. Use the up or down buttons to navigate to “Event Log”; press the enter

button.

3. Use the up/down buttons to scroll through events.

4. When viewing transmitter events, press enter to see the output the

events map to.

Note: No output will be displayed if the event is mapped to a null output.

Table 1: EN4216MR Supported Transmitters

Transmitter Alarm 1 Alarm 2 Alarm 3 Alarm 4

EN1215EOL Terminal

block

EN1215WEOL Terminal

block

Reed

switch

EN1223D Both

buttons

EN1235SF Button

EN1235DF Both

buttons

EN1244 Smoke

EN1245 CO

EN1249 Bill trap

EN1261HT Motion

Table 2: Default Trouble Condition Programming

Output/Relay Condition

6 Tamper

6 Low Battery

6 Supervision Loss/Inactive

See Figure 4,

“EN4216MR terminals”

on page 2.

Line Power Loss

Especificaciones del producto

Marca:	Inovonics
Categoría:	receptor
Modelo:	EN4216MR

¿Necesitas ayuda?

Si necesitas ayuda con Inovonics EN4216MR haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

receptor Inovonics Manuales

Inovonics EN4216MR Manual de Usario

17 Septiembre 2024

receptor Manuales

Últimos receptor Manuales

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024

Boss PT3000 Manual de Usario

27 Octubre 2024

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024

Fosi Audio V3 Manual de Usario

26 Octubre 2024

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024

NAD C 355BEE Manual de Usario

20 Octubre 2024

Yamaha RX-A810 Manual de Usario

20 Octubre 2024