InSinkErator Evolution 250 Manual de Usario

InSinkErator No categorizado Evolution 250

Lee a continuación 📖 el manual en español para InSinkErator Evolution 250 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

In Australia, removal of knockout plug does not apply. It is suggested

that the dishwasher units be connected to IPLEX/ COROMA dishwasher

spigot for maximum efciency.

Wastewater from a dishwasher can be plumbed into the disposer through

the inlet access on the upper part of the disposer. There is a plug on the

inside of the inlet tube on all models. Once removed, the knockout plug

cannot be replaced.

REMOVE KNOCKOUT PLUG

1. Lay disposer on its side and insert slotted screwdriver into dishwasher inlet

so tip rests on outer edge of knockout plug.

2. Tap end of screwdriver handle with hammer until molded plug breaks

loose. (See Figure 6.1)

3. Remove loose knockout plug from inside disposer. (See Figure 6.2)

MOUNTING ASSEMBLY

1a. Strainer Basket and Plug

w/ Cover (Evolution Models

250 & 150, Model E75)

1b. Strainer Basket and Plug

(Evolution Models 100 & 200,

Model BW5)

1c. Stainless Steel Stopper

(Model 66, BW4)

2. Sink Flange

3. Rubber Gaskets (2)

4. Fiber Gasket (optional)

5. Backup Flange

6. Mounting Ring

DISCHARGE ASSEMBLY #1

(Evolution Models,

Model BW5)

15. Hose Clamp

16. Elbow Discharge Tube

(38 mm diameter)

17. Straight Discharge Tube

(optional)

DISCHARGE ASSEMBLY #2

(Models 66, 56, 46, BW5, BW4,

BW3, BW2, E75)

17. Straight Discharge

Tube (optional)

18. Bolts (2) 13 mm 1/4-20 UNC

19. Rubber Gasket

20. Metal Flange

21. Elbow Discharge Tube

(38 mm diameter)

DISPOSER

9. Sound Bafe

(Evolution Models, Models

66, 56, BW5, BW4, BW3, E75)

10. Mounting Gasket

11. Lower Mounting Ring

12. Dishwasher Inlet

13. Discharge Outlet

14. Wrenchette

DISCHARGE TUBE INSTALLATION

(Evolution Models and Model BW5)

Place discharge tube (2 or 3) into Anti-Vibration Tailpipe Mount

™. Secure with

spring type hose clamp (1). (See Figure 7.1)

DISCHARGE TUBE INSTALLATION

(MODELS 66, 56, 46, BW4, BW3, BW2, E75)

1. Place metal ange (5) over discharge tube (7 or 8). Insert rubber gasket (4) with

gasket lip facing the metal ange into discharge tube. (See Figure 7.2)

2. Secure metal ange and discharge tube to disposer with two 13 mm bolts 6).

4.1

www.insinkerator.com

31.8 cm 16.6 cm 6.5 cm 20.0 cm 13.1 cm

30.8 cm 6.5 cm16.6 cm 13.1 cm

33.0 cm 6.4 cm 23.4 cm18.5 cm 16.8 cm

31.1 cm 17.1 cm 6.4 cm 22.2 cm 16.8 cm

(Evolution) 200-3B, 250-3

(Evolution) 100-3B, -11B, 150-3

Model 66-3, -10, E75-3

30.8 cm 6.5 cm16.6 cm 19.4 cm 13.1 cm

Model 56-3, -10, -11

BW4 -10

BW5 -10

BW3 -10

BW2 -10

Model 46-3, -10 18.9 cm

31.8 cm 16.6 cm 6.5 cm 20.0 cm 13.1 cm

30.8 cm 6.5 cm16.6 cm 13.1 cm

30.8 cm 6.5 cm16.6 cm 19.4 cm 13.1 cm

18.9 cm

2.1 2.2

Food waste disposers can provide an environmentally responsible alternative to transporting food waste to landlls. And they can help reduce greenhouse gas

emissions. At capable wastewater treatment plants, food waste can be recycled to produce renewable energy. Additionally, capable wastewater treatment plants

can process food waste into fertilizer. (Check the plant in your area).

Read through the entire installation manual before installing the disposer. Determine which of the tools, materials, and accessories you will need before

you begin. Make sure you have all necessary disposer parts before installing the disposer.

NOTE: The Evolution models and Model BW5 grind much ner than any other disposer. For this reason you may notice that it takes a little longer to grind some

food waste. Due to the Evolution 200/250 model’s microprocessor, users will experience a fractional second delay when starting on all Evolution 200/250 models.

This is completely normal.

NOTE: In Australia, all plumbing and electrical work must be completed by a qualied tradesperson. This product may require approval of the relevant regulator

and/or the sewerage system operator. Disposer must be installed to AS/NZS 3500.2 standard requirements.

NOTE: Make sure that the installation of this appliance is allowed by the authorities.

TOOLS & MATERIALS YOU WILL NEED:

Slotted Screwdriver, Adjustable Pliers, Safety Glasses

TOOLS, MATERIALS, AND ACCESSORIES YOU MAY NEED:

Phillips Screwdriver, Drain Auger, 9.5 mm Electrical Clamp, 38 mm Drain Trap, 33 mm Hole Drill, Hammer, Hacksaw, Water Hose Clamp, Pipe Wrench, Copper Earth

Wire, Dishwasher Drain Connection Kit, Electrical On/Off Switch, Drain Tube Extension

1. Disposer height.

2. Distance from bottom of sink bowl to centerline of discharge outlet. (Add

12 mm when stainless steel sink is used.)

3. Distance from centerline of the discharge outlet to end of discharge tube.

4. Disposer width.

5. Distance from disposer vertical centerline to centerline of trap connection.

DISCONNECT SINK DRAIN

1. Loosen nuts (1) at top of trap (4) with pipe wrench. Remove trap.

(See Figure 2.1)

2. Loosen nut (2) at top of extension pipe. Remove extension pipe.

3. Remove nut (3) at base of sink ange.

4. Push strainer up through sink hole and remove it. (See Figure 2.2)

5. Clean sink ange area of any putty or other debris.

The sink hole may have to be enlarged to accept the disposer NOTE:

sink ange. Sink hole enlargement tools are available from your

InSinkErator dealer.

CLEAN SINK DRAIN

Failure to clean sink waste pipe line may result in waste pipe blockage.

With drain auger, clear away all hardened waste material in horizontal drain

line running from drain trap to main pipe.

When installing in new construction, cleaning the sink waste pipe line is

not necessary.

IF REPLACING AN EXISTING DISPOSER,

CONTINUE WITH INSTRUCTION 3.

IF THIS IS A FIRST TIME INSTALLATION,

SKIP AHEAD TO INSTRUCTION 4.

1. Turn mounting assembly over (see Figure 4.1) and loosen three mounting

screws (1) until you can access snap ring (2).

2. Use screwdriver to pry snap ring off of sink ange. Mounting assembly can

now be disassembled.

Reference Figure 5.1.

1. Place one of two rubber gaskets (2) under sink ange (1). Ensure sink hole

area is clear of debris and place sink ange/gasket into sink hole. You may

wish to place a weighted object in the sink to hold the sink ange in place.

(Place a towel under object to prevent scratching.)

2. Working from under the sink, slip second rubber gasket (2), ber gasket

(optional) (3) and metal backup ange (4) (at side up) over the sink ange.

Holding second rubber gasket, ber gasket (optional) and metal backup

ange in place, slip mounting ring (5) over sink ange so it seats against

backup ange.

3. With the rubber gasket, ber gasket (optional), backup ange, and

mounting ring tight against sink bottom, slide snap ring (7) onto sink

ange until it pops into groove on ange.

4. Tighten three mounting screws (6) up to sink until mounting assembly is

seated tightly and evenly against sink.

IF YOU ARE NOT CONNECTING A DISHWASHER

TO DISPOSER, SKIP AHEAD TO INSTRUCTION 7.

FOOD WASTE DISPOSER INSTALLATION AND USE MANUAL

CHECK INSTALLATION DIMENSIONS

DISCONNECT AND CLEAN SINK DRAIN

DISASSEMBLE NEW DISPOSER

MOUNTING ASSEMBLY

PARTS LIST (May vary depending on model)

3 6

5.1

78174 Rev E

7.2

EVOLUTION MODELS, BW5

66, 56, 46, BW4, BW3, BW2, E75

7.1

4 4

ATTACH DISCHARGE TUBE TO WASTE DRAIN PIPE

Warning indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Caution indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Notice is used to address practices not related to personal injury.

PERSONAL INJURY

Wearing safety glasses is recommended during the installation of the

food waste disposer.

PROPERTY DAMAGE

• All Evolution Models and Model BW5 must be connected to the supplied

tailpipe with the supplied spring type hose clamp (See Figure 7.1). In

Australia it is required to use the supplied straight discharge tube with

supplied spring type hose clamp. (See Figure 7.2) Failure to use the

supplied tubes and spring type hose clamp will void the guarantee and

possibly cause premature failure of the Anti-Vibration Tailpipe Mount

™.

• Do not use plumber’s putty on any other disposer connection. Do not

use thread sealants or pipe dope. These may harm disposer and cause

property damage.

• Regularly inspect disposer and plumbing ttings for water leaks,

as water leaks can cause property damage. Manufacturer cannot

be held responsible for property damage as a result of water leaks.

• To properly drain and prevent standing water in the disposer when

utilizing a straight pipe discharge tube, the tube connection opposite

the disposer outlet must be lower – not higher – than the disposer outlet.

NOTICE

PERSONAL INJURY

To avoid personal injury, do not position your head or body under

disposer; the unit could fall during installation.

ELECTRICAL SHOCK

• To avoid electrical shock, disconnect power before removing any existing

disposer. Turn off electrical power at fuse box or circuit breaker or if

equipped unplug disposer electrical power plug from wall outlet.

• Improper connection of equipment earth (grounded) conductor can

result in electric shock.

1. If your disposer is equipped with an electric plug and cord connection,

unplug power plug from electrical wall outlet.

If your disposer is not equipped with an electrical plug and cord

connection, contact an electrician to disconnect the old disposer plus

install an earth (grounded) electrical wall outlet for the new disposer

connection that must be compliant to all local electrical codes.

2. Disconnect drain trap from disposer waste discharge tube with

adjustable pliers (see Figure 3.1). Also disconnect dishwasher drain

connection, if applicable.

3. Support disposer with one hand and insert end of wrenchette or

screwdriver into right side of one mounting lug on lower mounting ring

(see Figure 3.2). Lift disposer slightly and remove from mounting by

pushing or pulling wrenchette or screwdriver to left (disposer may be

heavy; provide support).

4. Loosen three mounting screws, pry snap ring off with screwdriver,

and remove old mounting assembly (see Figure 3.3). Some mounting

assembly removal requires additional tools.

5. Push old sink ange up through sink hole (see Figure 3.4).

REMOVE EXISTING DISPOSER

6.1

6.2

6REMOVAL OF KNOCKOUT PLUG

FOR DISHWASHER CONNECTION

5ATTACH UPPER MOUNTING ASSEMBLY TO SINK

In Australia, dishwasher attachment and over ﬂow connection does not

apply. It is suggested that the dishwasher units be connected to IPLEX / COROMA

dishwasher spigot for maximum efciency.

If you have a sink overow, it should be connected to the overow inlet on

the tailpipe (see Figure 10.1).

To connect the overow, remove the plug in the tailpipe by unscrewing the overow

connector cap (see Figure 10.2).

FOR NEW ZEALAND ONLY Connect the hose from the dishwasher to the dis-

poser inlet using a dishwasher drain connection kit with a hose clamp

(not provided).

NOTE: The straight discharge tube for use in Australia does not have an overow

connection tube.

DISHWASHER ATTACHMENT

AND OVERFLOW CONNECTION

This specication label contains important information the owner will need to

know in the event service is required. Place the portion of the specication label

removed in Step 8.1 somewhere easily visible to the user.

IF YOU ARE NOT CONNECTING A DISHWASHER

TO DISPOSER, SKIP AHEAD TO INSTRUCTION 11.

ATTACH SPECIFICATION LABEL

8.3

8.2

8.1

8.4

MODEL X X – XX

S/N X XXXX XXXX X

PUS H RED BUTTO N

TO RE SE T

CONNECT DISPOSER TO MOUNTING ASSEMBLY

Clear any objects from inside the disposer grind chamber before mounting

the disposer to the sink.

1. This product must be installed so that the red motor reset button, power

supply cord plug and earth ground receptacle are readily accessible.

Keep this space clear of all objects.

2. Prior to connecting disposer to mounting assembly, detach the perforated

portion of the specication label found at the base of the disposer, and set

aside for Instruction 9. (See Figure 8.1)

3. Lift disposer, insert top end (mounting gasket) into mounting assembly.

Position disposer with three mounting tabs (1) aligned in position to slide

over mounting tracks (2) (see Figure 8.2).

4. Turn lower mounting ring to right (with wrenchette or adjustable pliers) until

mounting tabs lock over ridges (3) on mounting ring tracks (see Figure 8.3).

Disposer will now hang by itself.

5. For Evolution Models, Models 66, BW5, BW4 and E75 Insert sound bafe

into sink opening, with at side upward. (See Figure 8.4)

6. Rotate disposer so that discharge tube is aligned with drain trap. (To

prevent leaks, do not pull or bend discharge tube to drain trap.) If discharge

tube is too short, you can purchase an extension from hardware store.

(Disposer must remain in vertical position to prevent vibration.)

7. Place nut, then ferrule on discharge tube and tighten on drain trap. (If you

have a double sink, use separate drain traps for both sides of sink.)

8. Ensure lower mounting ring is still securely locked over ridges on mounting

ange. (See Figure 8.3)

PERSONAL INJURY

To avoid personal injury, do not position your head or body under

disposer; the unit could fall during installation.

MODEL XX – XX

S/N XXXXXXXXXX

9.1

10.2

10.1

AIR SWITCH

(Evolution models,

Models 66, 56, BW5,

BW4, BW3, E75)

22. Air Switch Assembly

23. Tube

SAFETY SYMBOLS

PROPERTY DAMAGE

If the dishwasher connection is made without removing the plug,

the dishwasher may overow. (Connections must comply with local

plumbing codes.)

NOTICE

3.1

3.2

3.3

3.4

Read all safety messages before proceeding

Parex Industries Ltd.

5 Tolich Place, Henderson

Auckland, New Zealand 0610

Service and Sales Tel:

0800 200 510

Website: www.insinkerator.co.nz

InSinkErator

471 Mountain Highway

Bayswater Vic 3153, Australia

Sales Tel: 61 03 9720 5599

Service Tel: 1 300 136 205

www.insinkerator.com.au

InSinkErator

Emerson Electric Co.

4700 21st Street

Racine, WI 53406-5093

USA

Sales/Service Tel:

262-554-3652

www.insinkerator.com/worldmap.html

NOTICE

To properly drain and prevent standing water in the disposer, the waste

pipe entering the wall must be lower than the disposer discharge outlet.

Make sure all three mounting tabs are locked over ridges.

NOTICE

220-240V, 50-60Hz

7. Screws (3)

8. Snap Ring

DON’T...

• DON’T POUR GREASE, OIL OR FAT

DOWN YOUR DISPOSER OR ANY

DRAIN. It can build up in pipes and

cause drain blockages. Put grease in

a jar or can and dispose in the trash.

• DON’T use hot water when grinding food

waste. It is OK to drain hot water into the

disposer between grinding periods.

• DON’T turn off water or disposer until

grinding is completed and only sound of

motor and water running is heard.

• DON’T grind brous materials like

corn husks, artichokes, etc., in any

Models 66, 56, 46, BW4, BW3 or BW2 to

avoid possible pipe blockage.

Also avoid grinding animal skins in

these models.

• DON’T grind raw chicken or duck feet in

any disposer.

• DON’T grind non-food waste of anykind.

• DON’T use this appliance to dispose of

hard materials such as glass and metal.

• DON’T ll disposer with a lot of food

waste all at once. Instead, turn the

water and disposer on rst and then

feed the food waste in gradually.

• DON’T waste food. Nearly a quarter

of the food we buy is thrown away

untouched: salad, bread and cakes

and fruit head the list. Three tips to

stop waste and save you money: only

buy, or cook, the portions you need for

the meal; check the fridge and cupboard

for food you haven’t eaten – make it

your next snack or freeze it; and make

sure you leave that food off your next

shopping list!

11.1 11.3

11.5

11.2

11.4

33 mm

AIR SWITCH (Evolut ion Models, MODELS 66, 56, BW5, BW4, BW3

and E75)

The Evolution Models, Model 66, Model 56, Model BW5, Model BW4, Model BW3

and Model E75 disposers include a built-in air switch. An air switch activates/

turns off the unit by sending a pulse of air to the control box.

AIR SWITCH INSTALLATION

If you wish to change the button nish (optional), simply pry off the existing

button and snap the other button nish onto the bellows. (See Figure 11.2)

1. Drill a 33 mm wide hole into the kitchen work top, or the corner of the sink

unit, at the most convenient point for use. Some sink units may already

have a suitable hole in them which can be exposed by removing the cap.

2. Remove the nut from the push button bellows, while keeping the stainless

steel washer and rubber gasket in place. Push one end of the PVC tubing

onto the spout of the push button bellows, feed the other end of the tube

through the hole in the work top and through the nut underneath the work

top. (See Figure 11.3)

3. Fit the push button bellows in the hole and then thread the nut underneath

the work top until it is hand tight. . Do not use a wrench to tighten the nut

(See Figure 11.4)

4. Take the other end of the air tube and rmly push it over the spout of the

air switch, which is located on the underside of the waste disposer

(See Figure 11.5).

DISABLING THE AIR SWITCH

The air switch can be disabled if wall switch operation is preferred.

The disposer is shipped with the switch in the “off ” position.

1. Push one end of the PVC tubing provided onto the spout of the push

button bellows. (See Figure 11.3)

2. Take the other end of the air tube and rmly push it over the spout of the

air switch, which is located on the underside of the waste disposer

(See Figure 11.5).

3. Depress the air switch one time until you hear the switch “click.” Remove

and discard the push button bellows and PVC tubing. The disposer may

now be activated by a wall switch.

The disposer installation is complete. Read all operating and safety

instructions in Instruction 12 before operating the disposer.

Lastly, place stopper in sink in close position. Fill sink with water,

remove stopper, turn disposer on and check for leaks.

ELECTRICAL SHOCK

• If three-prong, ear th (grounded) plug is used, plug must be inserted

into three-hole, earth (grounded) receptacle.

• Do not modify plug provided with unit (if applicable).

• Improper connection of equipment earth (grounded) conductor can

result in electric shock.

• All wiring must comply with local electrical codes.

• Do not attach earth wire (ground wire) to gas supply pipe.

• Do not reconnect electrical current at main service panel until proper

earth (grounded) outlets are installed by a qualied electrician.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualied-persons in order

to avoid a hazard.

NOTE: You must have access to a separate circuit wall socket that is

earth (grounded) to main service panel. Any additional socket should

be tted by a qualied electrician and properly earthed (grounded). The

disposer is tted with a power supply cord plug.

ON/OFF CONTROL

There are two types of controls for continuous-feed disposers: a double-

pole switch and an air switch (built in for Evolution Models, Model 66, Model

56, Model BW5, Model BW4, Model BW3 and Model E75; available as an

accessory on all other models).

DOUBLE POLE SWITCH (1):

If a wall switch (not supplied) is required for your installation, it must have

on/off markings and be installed by a qualied tradeperson. It should be

located in a convenient position above the work surface with a minimum of

3 mm contact separation between each pole. In New Zealand, please refer

to AS/NZS 3000:2007 for electrical installation. Connect to a 20 amp earth

(grounded) wall socket (2) using a 20 amp cable. (See Figure 11.1)

See instructions for DISABLING THE AIR SWITCH.

CONNECT DISPOSER TO ELECTRICAL SUPPLY IMPORTANT SAFETY INFORMATION

IN-HOME FULL SERVICE GUARANTEE

11 12

OPERATING INSTRUCTIONS

(EVOLUTION MODELS, Model BW5)

1. Remove strainer basket and plug from

sink opening and run cold water.

2. Turn on wall switch or press air switch

(see Figure 12.1) to start disposer.

3. Slowly insert food waste into disposer

and position strainer basket and plug in

upright position (allowing water to run

through) to minimize noise and possible

ejection of material while grinding

(See Figure 12.2).

4. After grinding is complete, turn disposer

off and run water for a few seconds to

ush drain line.

5. Strainer basket and plug also acts as a

stopper in the lower position.

(See Figure 12.3)

OPERATING INSTRUCTIONS

(MODELS 66, 56, 46, BW4,

BW3, BW2, E75)

1. Remove stopper from sink opening and

run cold water.

2. Turn on wall switch or press air switch

(see Figure 12.1) to start disposer.

3. Slowly insert food waste into disposer

and position stopper to minimize

possible ejection of material while

grinding. (See Figure 12.4)

4. After grinding is complete, turn disposer

off and run water for a few seconds to

ush drain line.

DO...

• First turn on cold water and then turn

on the disposer. Continue running cold

water for a few seconds after grinding

is completed to ush the drain line.

• Grind small amounts of hard material

such as bones, fruit pits, and ice.

A scouring action is created by the

particles inside the grind chamber.

• Grind peelings from citrus fruits to

freshen up drain smells.

• Grind food waste with minimum cold

water ow of 6 liters per minute.

• Grind common food waste, such as

fruits, vegetables, meats, bones, coffee

grounds, etc.

• Switch off or unplug the appliance

before attempting to free a jammed

disposer with the wrenchette.

• Maintain the area around the disposer

free of any objects to be sure you have

access to the disposer reset button.

12.4 12.5 12.612.312.212.1

MODEL XX – XX

S/N XXX XX XXX XX

PUSH R ED BUTTO NTO R ESET

MOD EL XX – X X

S/N XXXXXXXXXX

PUSH RED B UT T ON

T O RES ET

Models

46/56/66/BW2/

BW3/BW4/E75

Evolution®

100/150

Model BW5

Evolution®

200/250

Everyday

food waste √ √ √

Vegetable

peels √ √ √

Plant bre,

animal

skins

Avoid grinding

large amounts at

once

√

Bones Avoid grinding

large bones √ √

Warranty is determined by the unit serial number and the date of installation.

Purchase or installation receipt may be required to verify warranty status.

SERVICE

If service is required, contact an InSinkErator Authorized Service Center

or your dealer. Guarantees are void if you remove your disposer after installation

and attempt to repair it, or if the disposer is used for commercial purposes.

Evolution 150-3: 7 years

Evolution 200-3B: 6 years

Evolution 250-3: 8 years

Model 66-3, -10: 4 years

Model 46-3, -10: 2 years

Evolution 100-3B, -11B: 5 years

Model 56-3, -10, -11: 3 years

Model BW5-10: 5 Years

Model BW4-10: 4 Years

Model BW3-10: 3 Years

Model BW2-10: 2 Years

Model E75-3: 5 years

RELEASING DISPOSER JAM

If the motor stops while the disposer is

operating, the disposer may be jammed.

To release jam:

1. Turn disposer power and water off.

2. Insert one end of the self-service

wrenchette into the center hole on the

underside of the disposer (see Figure

12.5). Work the wrenchette back and

forth until it turns one full revolution.

Remove wrenchette.

3. Reach into the disposer with tongs and

remove object(s). Allow the disposer

motor to cool for 3 - 5 minutes and

lightly push red reset button on the

underside of the disposer (see Figure

12.6). (If the motor remains inoperative,

check the service panel for tripped

circuit breakers or blown fuses.)

CLEANING DISPOSER

Over time, grease/food particles may

accumulate in the grind chamber and

bafe, causing an unpleasant odor. To

clean the disposer:

1. Turn off disposer and disconnect

power supply.

2. Reach through sink opening and

clean underside of splash bafe and

inside upper lip of grind chamber with

scouring pad.

3. Place stopper in sink opening and ll

sink halfway with warm water.

4. Mix 60 ml baking soda with water.

Turn disposer on and remove stopper

from sink at same time to wash away

loose particles.

PERSONAL INJURY

Install and route tubing for air switch as such to reliably reduce likelihood

of mechanical damage or stress, allowing proper on/off operation of the

air switch.

When using electronic appliances,

basic precautions are always to be

followed, including:

• In Australia, product may require

approval of the relevant regulator

and/or the sewerage system operator.

• If the air switch or wall switch fails to

shut off or turn on disposer, unplug

power cord plug and contact your

qualied trade person.

• This product is designed to dispose of

normal household food waste;

inserting materials other than food

waste into disposer could cause

personal injury and/or property

damage. To reduce the risk of injury,

do not use the sink containing the

disposer for purposes other than

food preparation (such as baby bathing

or washing hair).

• This appliance can be used by children

aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or

lack of experience and knowledge if

they have been given supervision

or instruction concerning use of the

appliance in a safe way and under

stand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

• When attempting to loosen a jam in

the food waste disposer, switch off or

unplug the appliance before attempting

to free a jammed rotor. Use a self

service wrenchette as described in the

Releasing Disposer Jam section.

• Use long-handled tongs or pliers to

remove objects from disposer.

• To reduce the risk of injury by materials

that are expellable by a waste disposer,

do not operate Evolution or Model BW5

disposers without the sound bafe in

place (see Figure 8.4). Place stopper in

sink opening as shown in Figure 12.2

or 12.4. Do not put the following into a

disposer: clam or oyster shells, caustic

drain cleaners or similar products,

glass, china, or plastic, large (whole)

bones, metal (such as bottle caps, steel

shot, tin cans, or utensils), hot grease or

other hot liquids.

• Replace sound bafe/mounting gasket/

splash bafe when worn to help prevent

entry or ejection of material and water.

• When not using disposer, leave stopper

in place to reduce risk of objects falling

into disposer. Make sure disposer

power switch is turned off.

• Before pressing reset button,

attempting to clear jam, or removing

objects from inside disposer, make sure

disposer power switch is turned off.

• Do not insert hands or ngers

into disposer.

• FIRE HAZARD: Do not store ammable

items such as rags, paper, or aerosol

cans near disposer. Do not store or use

gasoline or other ammable vapors and

liquids in vicinity of disposer.

• LEAK HAZARD: Regularly inspect

disposer and plumbing ttings for

leaks, which can cause property

damage and could result in

personal injury.

• Do not dispose of the following in the

disposer: paints, solvents, household

cleaners and chemicals, automotive

uids, plastic wrap.

Especificaciones del producto

Marca:	InSinkErator
Categoría:	No categorizado
Modelo:	Evolution 250

¿Necesitas ayuda?

Si necesitas ayuda con InSinkErator Evolution 250 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado InSinkErator Manuales

InSinkErator Evolution 250 Manual de Usario

6 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024