IXL Tastic Ovation Manual de Usario

IXL Calentador Tastic Ovation

Lee a continuación 📖 el manual en español para IXL Tastic Ovation (2 páginas) en la categoría Calentador. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Quick Guide

NOTE: This product must be installed by a qualied installer.

1. Determine The Placement Of The Unit

• Ensure clearance to joists, beams etc. in ceiling

• Check the path of the duct in the ceiling

• Use the cutout template in the top ap of the product carton

Cutout Dimensions: 332 mm x 462 mm

2. Install Standard Wall Switch and Wiring

• Connect unit as per wiring diagram.

• Wiring of the unit is designed so that the LED and Heat cannot

operate at the same time

3. Ducting

• Select and cut duct outlet location

• Ensure ducting is pulled taut before cutting and installing outlet grille

• Avoid bends and kinks as this will reduce the extraction performance

100%

80% 60%

4. Install unit and test

• Assemble outlet and tape to duct. Connect to unit.

• Load fully connected unit into ceiling cavity

• Install lamps and fascia

Connection

A local isolating switch (not supplied) must be incorporated in the

xed wiring to the appliance to allow disconnection of supply during

maintenance.

The Tastic Ovation is classied as a Room Heater and as such:

In accordance to AS/NZS 3000 this isolating switch shall be -

(a) installed immediately adjacent to an entrance to, or within, the

room where the room heater is located; or

(b) installed on the switchboard at which the room heater nal

subcircuit originates.

Refer to AS/NZS 3000 for further regulations regarding

isolating devices.

For comments, questions or warranty matters:

IXL Home Pty Ltd

Australia

Free Call: 1300 727 421

service@ixl.com.au

www.ixlappliances.com.au

New Zealand

Free Call: 0800 727 421

service@ixl.com.au

www.ixlappliances.co.nz

ON HEAT LAMP

& EXHAUST FAN Approved by the appropriate

electrical supply authorities.

Part number: 611059 A

IXL, TASTIC and OVATION

are registered trademarks of

Alver Pty Ltd in Australia and

New Zealand used under

licence by IXL Home Pty Ltd.

Safety

Read through these instructions completely before

commencing installation.

NOTE: This product must be installed by a qualied installer.

Locate the Tastic in accordance with the requirements of the current

Australian/New Zealand Wiring Rules AS/NZS 3000 relating to damp

situations. In some installations this may mean that no part of these

Tastic may be located directly above any part of a bath or shower

recess or enclosure.

For unenclosed showers refer to Wiring Rules conditions.

Switches and other controls must not be located where they can be

touched by a person in the bath or shower.

• Tastic products are not tanning lamps.

• Do not operate this appliance without the fascia or glass panels

in position.

• This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

• Young children should be supervised to ensure they do not play with

the appliance.

• This appliance must be mounted with the lowest point at least 2.2

metres from the oor.

• This appliance must not be mounted immediately below a

socket outlet.

• Regulations concerning the discharge of air have to be fullled.

WARNING: Curtains or combustible material may ignite if in contact

or close proximity with the heater.

Installation Guide

Electrical rating: 230~240 V. 50 Hz.

Model: 31511 Tastic Ovation

OVATION

• When installed, the Tastic appliance

shall, under no circumstance, be

covered with insulating material or

similiar material.

• This Tastic unit must be installed

horizontally in the ceiling.

• There is no IP rating on this IXL

Tastic Ovation.

• To prevent overheating do not place

any object within 1 metre of heat lamps.

In order to avoid a hazard due to

inadvertent resetting of the thermal cut

out, this appliance must not be supplied

through an external switching device,

such as a timer, or connected to a circuit

that is regularly switched on and off by

the utility.

Ducting

(Supplied)

Air outlet grille

positioned in eaves lining

Exterior

of home

Eaves

lining

Tastic unit

Cable

Wall switch (supplied)

Isolating switch (not supplied)

Tastic Ovation: 31511

Ventilation Requirements

For maximum efciency and fan

performance there are a few key points to

keep in mind when installing your Tastic.

Sufcient air inlet into room

Steam will only be removed if there is

sufcient ow of air through the room.

Ensure adequate inlets exist through

windows, vents or under the door.

Airow path from inlet to fan should ideally

pass over the steam sources (see Fig.1).

Bathrooms which have high ceilings, are

larger then average, or have an open

shower may all require additional ventilation

to be installed.

We recommend that you visit our website

for further details and suggestions on

effectively ventilating your bathroom.

Clearances

Minimum internal ceiling clearances

- from ceiling to lowest point of ceiling

cavity: 240mm (to maintain minimum

15mm clearance) (Fig 2a).

- from top of ceiling joists to ceiling cavity:

150mm (duct diameter) (Fig 2a).

If the desired orientation of the Tastic unit

directs the ducting towards a ceiling joist,

ensure that the closest ceiling joist is not

within 200 mm of the Tastic outlet. (Fig 2a).

(Ensure that the outlet of the Tastic is

directed towards the outer wall)

Clearance to joists or battens

(all around unit): min 35mm ((Fig 2b).

Minimum ceiling height is 2.2m.

Recommended maximum ceiling

height :2.7m

Exhaust Fan Capacity 396m³/h

Recommended Room Size

Single Area Suitability:

8.3m² with shower / 20m² without shower

Based on standard 2.4m ceiling height

Installation

Install between Joists (Fig. 4)

IMPORTANT: Joists, beams and rafters

shall not be cut or notched to install the

appliance.

The Tastic Ovation has a weight of 5.5 kg.

If adequate support is not available for the

Tastic, it may be necessary to provide extra

strengthening.

If ceiling battens have been cut to install this

then ensure that the cut ceiling battens are

adequately secured to rafters.

NOTE: This product must be installed

by a qualied installer.

1. Cut out hole for Tastic body

After determining the location of

components according to the directions,

mark out and cut aperture in ceiling for

Tastic Ovation unit using this template.

Trim the template to the dashed cut line.

Cutout Size: 332 mm x 462 mm

2. Ducting

Determine the minimum length of ducting

required to outside exhaust vent by keeping

the duct length as short as possible the

exhaust performance is maximised. Refer to

Fig’s 5-7.

Note: These products have been designed

to suit 150mm dia. ducting.

Installation

Installing the Ducting

NOTE: The fan outlet is assembled to the

Tastic Ovation during nal assembly before

mounting into the ceiling.

1. Install the backdraft aps into the

removable duct outlet (Fig. 8)

2. Tape the duct onto the long end of the

outlet.

3. Feed ducting through hole in ceiling.

Directing it towards the installation

position of the outlet grille.

Installing The Unit

1. Complete the wiring

• Open the terminal cover and connect

wiring to terminal block as per the wiring

diagram on reverse of this page.

• Route the wiring from the terminal block

along the guides and clamp under the

plastic nipper to aid installation (Fig. 10).

2. Clip outlet with duct attached to the

Tastic body - Engage locking pins and

twist to lock (Fig. 9).

Ensure that the ducting taped to the outlet

is not dislodged in the process.

3. Push the body into the aperture, allowing

the metal springs to snap open to retain

the unit in the ceiling.

As the Tastic is raised into ceiling, ensure

electrical cables are in a safe position.

(Fig 11).

4. To secure the unit in position, push lower

ends of springs apart (Fig 12).

Fit LED Lights

5. Connect all of the LEDs to the globe

holders attached to the Ovation unit.

6. Lift the fascia up to the unit and clip the

LEDs into the recesses on the back of the

fascia. There are 2 tabs in each recess to

clip into. (Fig 13).

7. Once all the LEDs are secure in the

fascia, push the fascia rmly up into position

in the body. Ensure the fascia is in contact

with the ceiling all around the unit. (Fig 14).

Fig 1. Ideal placement of Tastic. Fig 4. Use template to mark position of Tastic

Fig 8. Fig 13.

Fig 2a. Minimum clearances for installation.

Fig 2b. Minimum clearances to joist.

Fig 5. Straight ducting

Fig 9. Fig 14.

Fig 3. Ceiling to wall clearances Fig. 7: Tightly compressed bends

Fig 11. Fig 16.

Fig. 6. Gradual bends, ducting stretched

straight.

Fig 10. Fig 15.

Fig 12. Fig 17.

Spring Clip

Tastic Unit

Push Spring Clip

to secure

Installation

Fit Heat Lamps

NOTE: Natural skin oils and salts damage

new halogen lamps and shorten their life.

Only handle a new heat lamp with soft, dry,

clean, lint-free cloth or paper.

You can wear gloves, cover your ngers or

wrap the heat lamp until it is installed (so

long as you remove all cloth or paper when

nished). If your skin touches a new heat

lamp, wipe it gently with alcohol-moistened

cloth or paper.

1. The heat lamp is half coated with a white

reector. When you grasp the heat lamp,

face the back of the reector to the ceiling

(so you can see the heat lamp’s lament).

Not doing this will reduce performance.

(Fig. 15)

2. Fit one end of the heat lamp into a socket

and gently push it away from the other

socket.

3. When there is enough room, t the other

end of the heat lamp into its socket.

4. Gently rotate the heat lamp to ensure it is

correctly seated (i.e. it looks like the old

one did before you removed it).

5. Switch the power on and test the heat

lamp.

6. Fit the glass sheets to the heat lamp

reector bodies (Fig. 16).

Step 1.

Insert the glass into the opening of the heat

unit nearest the lights.

Step 2.

Lift the glass into the opening on the other

side.

Step 3.

Slide the glass across so that it drops into

position.

7. Turn on the power at the isolating switch

and check operation of the Tastic.

Installing the external Grille

1. Cut a hole 160 mm in diameter in eaves

or outer wall.

2. Feed ducting out through this hole and

trim length (if required) to prevent kinks in

the duct per previous instructions.

3. Tape to the circular outlet on the grille

baseplate and feed the ducting back

through the hole so that the grille base is

against the eaves or outer wall.

4. Fix grille base with four 6 G screws and

snap t the grille louvres over the grille

base. (Fig. 17).

150mm

15mm

225mm

35mm

200mm min.

Perfor

mance

35 mm

100%

Performance

Filament

Socket

Heat Lamp

Reﬂector

Min

300mm Min

1500mm

Wall

Min

300mm

Sprinkler System/

Smoke Detector

Wall

Performance

100%

Mains power and

switch cables

Especificaciones del producto

Marca:	IXL
Categoría:	Calentador
Modelo:	Tastic Ovation

¿Necesitas ayuda?

Si necesitas ayuda con IXL Tastic Ovation haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Calentador IXL Manuales

IXL Tastic Ovation Manual de Usario

5 Septiembre 2024

Calentador Manuales

Últimos Calentador Manuales

Vonroc PH503AC Manual de Usario

27 Octubre 2024

JANDY VersaFlo Manual de Usario

27 Octubre 2024

Master 215TMHD-KFA Manual de Usario

25 Octubre 2024

Yamazen DBC-VK123 Manual de Usario

23 Octubre 2024

Yamazen DCT-B08 Manual de Usario

23 Octubre 2024

Yamazen DOL-J122 Manual de Usario

23 Octubre 2024

Yamazen DSF-S122 Manual de Usario

23 Octubre 2024

Yamazen DBC-SK123 Manual de Usario

23 Octubre 2024

Yamazen DBC-W121 Manual de Usario

23 Octubre 2024

Yamazen DMF-D021 Manual de Usario

23 Octubre 2024