J. Rockett Audio Designs APE Manual de Usario

J. Rockett Audio Designs No categorizado APE

Lee a continuación 📖 el manual en español para J. Rockett Audio Designs APE (3 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

MIX

REPEATS

DELAY

TIME

OUT

YOUR FAVORITE DELAY

INPUT

The APE can be configured in several different ways. The above configuration “A” is the series setup.

This allows you to use the APE in front of your delay. This will introduce the famous EP sound as well

but will not color the delayed notes like in Loop configuration. All of your delay controls will work as

they normally do, however, the APE will function differently. In this configuration the APE acts as a

preamp with no controls it just simply adds the influence of the EP sound which is wider and warmer.

It introduces a fat sound across the spectrum. Since it runs at 22.5v just like a real EP everything in

between the notes is cleaner and clearer. To introduce any controllable effect you must engage

the loop switch. Once the loop switch is engaged the “REC” knob becomes a treble boost and

gain. The “Mix” knob also controls output.

NOTE: Be careful to not crank the repeats control on the APE when in series or it can squeal loudly.

NOTE: When in config A and when the loop is engaged the repeats knob is a treble control, the mix

knob is an output control and the REC knob is a drive control. This is where you can add more EP

type push. This will not be the case when you loop in a delay.

NOTE: When using the APE with delays that do not have a mix control or go 100% wet we

recommend that you use it in the “A” configuration. The APE in the “B” configuration works best with

“flat frequency” digital delays. PT Chip delays and Analog delays seem to work best in the “A”

configuration. We encourage you try all configurations with any delay since we cannot try them all.

You may discover a great setup. The APE was intended to add the EP sound to those digital delays

lacking the warmth and fatness of the analog influence of an old EP, especially those delays that

claim to be a recreation of an EP. A real EP has no output control other than driving the record

head.

OTHER SETUPS: You can run your guitar into the “guitar input” and come out of the standard output

but you can also come out of the send or return. When you use the “Return” as the output you get

a fully bypass-able treble boost/gain controlled by the “REC” knob. When you use “Send” as the

output you get a non bypass-able clean boost controlled by the “REC” knob.

The APE works really well with BASS guitar but try it with everything…..you never know.

CONFIGURATION “A”

AMP

A.P.E. ( nalog reamp xperiment)A P E

MIX

REPEATS

DELAY

TIME

OUT

ALWAYS SET REPEATS

TO ABSOLUTE

MINIMUM OR 1 REPEAT

ALWAYS SET MIX TO

ABSOLUTE MAXIMUM

OR FULLY WET

YOUR FAVORITE DELAY

SET TO

DESIRED

DELAY TIME

The APE can be configured in several different ways. The above configuration “B” is the loop setup.

This allows you to loop your delay into the APE and let the APE take over some of the controls. You

will need to set your delay to 100% MIX or fully wet. You will need to set your repeats to only 1 repeat

or minimum. The APE will handle the repeats and the mix along with the record head level. The

Record head level adds gain to the delayed note. If you set the record head level low and the mix

high you will get cleaner delays. If you set the Record head leave; high and the mix low you will

have grittier delays, please experiment.

NOTE: Be careful to not crank the repeats control on the APE when in loop mode or it can send the

repeats into runaway mode..

The APE can be used in loop configuration or in series just like a typical pedal. Run the APE before

any delay and it will introduce the famous EP sound into your entire signal path. We prefer the APE

at the end of the chain just before a delay and/or reverb in loop or series configuration.

Things to experiment with: Try overdrives or boosts into the loop and you will find some amazing

Guitar Input

ar Output

CONFIGURATION “B”

A.P.E. ( nalog reamp xperiment)A P E

Warranty

Rockett Pedals LLC will repair or replace. , at its discretion defective ,

workmanship or materials on all new Rockett Pedals products directly

or through; the selling dealer or an authorized service technician for ,

one year from the date of purchase at no cost to the original

purchaser.

Repair and replacement parts installed will be warranted for the

unexpired portion of the original

warranty term.

Before sending product in for repair please contact us at

chris@rockettpedals com. or

jay@rockettpedals com.. +1 720 936-8623. Or call ( )

This warranty does not cover shipping costs product appearance or ,

damages caused by

accident abuse misuse or alteration, , .

A dated sales slip or order number (issued by a tech dealer or Rockett ,

Pedals) must accompany a product being returned for warranty

service Repairs without a return authorization number will be .

refused Please allow weeks for warranty service For more. 4 .

information please contact Rockett Pedals www.rockettpedals com. or

+1 720 936-8623. ( )

No other warranty is expressed or implied.

A.P.E. ( nalog reamp xperiment)A P E

Especificaciones del producto

Marca:	J. Rockett Audio Designs
Categoría:	No categorizado
Modelo:	APE
Color del producto:	Purple, White
Peso.:	1400 g
Ancho:	432 mm
Profundidad:	133 mm
Altura:	180 mm
Longitud del cable:	5.5 m
Filtro extraíble:	Ja
tipo de limpieza:	Droog
Tiempo de carga:	- uur
Tipo de contenedor de aspiradora:	Zakloos
tierra seca:	- l
Duración:	- min
Batería/Voltaje de la batería:	- V
Zuigstang:	Nee
herramienta para rincones:	Ja
Filtración:	Ja
voltaje-de-entrada-de-CA:	120 V
Consumo de energía (típico):	400 W