Jablotron JA-80W Manual de Usario
Lee a continuación 📖 el manual en español para Jablotron JA-80W (1 páginas) en la categoría Seguridad. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/1
JA-80W wireless combined PIR + MW detector 1 MLI51101
JA-80W wireless combined PIR + MW detector
The JA-80W is a component of Jablotron’s Oasis alarm system. It is
designed to detect human body movement inside buildings. A high immunity to
false alarms is reached thanks to the combination of PIR and microwave (MW)
detection. The PIR part, if triggered, starts the MW detection to confirm PIR
activation. Only then is the triggering transmitted.
Installation
Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. There should be no obstacles blocking the
detector’s “view” of the protected area. Keep the detector away from metal
objects which could interfere with radio communication and the MW field.
8
Description: 1. DIP-switch; 2. MW part connector; 3.PCB tab; 4. tamper-switch; 5.
PIR sensor; 6. front cover tab; 7. MW sensitivity setting; 8. MW detector
1. Open the detector cover by pressing the tab (6) and remove the PCB
which is held by an internal tab (3) Avoid touching the internal PIR
element or damaging the antenna.
2. Punch screw holes through the rear plastic cover according to the
installation point, either for a corner or for a flat wall At least one screw
should penetrate the tamper-sensitive section.
3. Screw the rear cover to the wall, about 2.5 meters above the floor
(vertically, with the tab down).
4. Return the PCB to its original place till the tab (3) clicks..
5. Leave the battery disconnected and the cover open and then follow the
control panel or receiver manual. The basics of enrollment are:
• Enter enrollment mode on the control panel by keying in “1” in
Service mode.
• Install a battery into the detector to activate enrollment.
• Exit enrollment mode by pressing “#”
6. Close the detector cover till the tab clicks. The supplied screw can secure
the tab.
7. After installing a battery into the detector, allow three minutes for
stabilization. During this period the LED is continuously lit.
Notes:
To enroll a detector after having already connected a battery, first disconnect
the battery, and press and release the tamper switch to discharge any
remaining charge to get the device ready for enrollment.
The detector can also be enrolled by entering the serial number – the last
eights numbers of the barcode, which is placed inside the detector.
To follow the EN 50131-2-4 the tab must be secured by the supplied screw.
DIP switch Setting
Switch no.1: DEL / INS: OFF (DEL) provides entrance & exit delays for
detectors installed in a building entrance route. The ON (INS) allows the
detector to instantly trigger alarm activation if the control panel is armed.
DIP switch no.1 only has an effect if the detector has a natural reaction
assigned to it in the OASiS control panel. It also has no effect when used with
a UC-8x or AC-8x receiver.
Switch no.2: PIR NORM / HIGH: selection of immunity to false alarms.
The OFF (NORM) position combines very good immunity with fast sensor
reactions. The ON (HIGH) position gives increased immunity with a slower
reaction time and is only used for problematic installations.
Switch no.3: MW NORM / HIGH sets the time period after PIR detection in
which the MW detection is active. The position OFF – 1 s, ON – 2 s
Switch no.4: MW NORM / TEST. The position OFF is for the standard function
of the detector. The MW detection is triggered by the PIR detection part for one or
two seconds according to switch no.3. The position ON - MW detection works
continuously for testing purposes (walk test).
Testing the detector
15 minutes after closing the detector cover, the LED indicators show detector
activation. A short flash of the red light indicates PIR detection and a long flash
(2 sec) indicates MW confirmation of the movement.
For the proper functioning of the detector, it is essential to set the MW
detection field according to the place which should be monitored. For setting
up, switch the fourth DIP switch to the TEST position. Sensitivity (monitoring
range) can be adjusted by a potentiometer on the MW detection part located
inside the front cover of the detector. Turning clockwise increases the
sensitivity (range). Avoid selecting too high a sensitivity as the detection can
cover e.g. nearby rooms. Generally the MW detection field should be the same
as the PIR detection one. After setting up, switch the DIP switch back to
NORM position.
To save battery energy, the PIR detector switches to battery-save mode 15
minutes after the cover is closed. During battery-save mode the PIR sensor still
always watches out for movement. The first movement detected and consecutively
confirmed by the MW part is then signaled to the control panel instantly, and for the
next 5 minutes the PIR sensor ignores any further movement. After these 5
minutes, the PIR sensor then returns to watching out for movement until re-
triggered.
Battery replacement
The detector regularly checks its battery conditions. If battery voltage is
too low, then the report is sent to the control panel to inform the user or
installer. The detector continues to work and each detected movement is
confirmed by a brief LED flash. The battery should be replaced within two
weeks by a qualified technician in SERVICE mode.
After battery replacement, test the functioning of the detector. Expired
batteries should not be thrown into the garbage, but disposed of according
to local regulations.
Removing the detector from the system
If a detector is removed, the control panel reports the removal. The detector
has to be deleted from its address in the control panel before intentional
removal.
Detection characteristics
Technical parameters
Power supply: Lithium battery type LS(T)14500 (3.6V / 2,4 Ah AA)
Typical battery lifetime: approx. 2 years (DIP switch 3: NORM)
Communication band: 868 MHz, Oasis Protocol
Communication range: approx. 300m (open area)
Recommended installation height: 2.0 to 2.5 m above floor level
PIR detection angle/detection range: 110° / 12 m (with basic lens)
MW detection range / frequency 0.5 to 20 m / 9.35 GHz
Operational environment according to EN 50131-1 II. indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, EN 50131-2-4, EN 50131-5-3 classification: grade 2
Dimensions, weight 110 x 60 x 55 mm, 140 g
Complies with ETSI EN 300220, ETSI EN 300 440-1, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
Operation requires notification national telecommunication offices of Finland, France, Italy,
Serbia and Montenegro, Spain, Sweden, UK
JABLOTRON ALARMS a.s. hereby declares that the
JA-80W is in compliance with the essential requirements
and other relevant provisions of Directive 99/5/EC. The
original of the conformity assessment can be found at
www.jablotron.com, Technical Support section
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
Especificaciones del producto
| Marca: | Jablotron |
| Categoría: | Seguridad |
| Modelo: | JA-80W |
¿Necesitas ayuda?
Si necesitas ayuda con Jablotron JA-80W haz una pregunta a continuación y otros usuarios te responderán
Seguridad Jablotron Manuales
4 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
3 Septiembre 2024
1 Septiembre 2024
30 Agosto 2024
30 Agosto 2024
Seguridad Manuales
- Seguridad Bosch
- Seguridad Panasonic
- Seguridad Grundig
- Seguridad Honeywell
- Seguridad Siemens
- Seguridad Abus
- Seguridad Alphatronics
- Seguridad Aritech
- Seguridad Prestigio
- Seguridad Airbolt
- Seguridad Brennenstuhl
- Seguridad Hikvision
- Seguridad Nedis
- Seguridad Yale
- Seguridad Tevion
- Seguridad Eminent
- Seguridad Blaupunkt
- Seguridad Ezviz
- Seguridad Trust
- Seguridad Elro
- Seguridad Doro
- Seguridad Axa
- Seguridad Optex
- Seguridad Axis
- Seguridad Theben
- Seguridad Maginon
- Seguridad Velleman
- Seguridad Smartwares
- Seguridad Easymaxx
- Seguridad Profile
- Seguridad Marquant
- Seguridad Trebs
- Seguridad Ednet
- Seguridad Fenton
- Seguridad Eufy
- Seguridad Perel
- Seguridad Steinel
- Seguridad Somfy
- Seguridad Goliath
- Seguridad Devolo
- Seguridad Lamax
- Seguridad Audiovox
- Seguridad Netgear
- Seguridad Nest
- Seguridad Grothe
- Seguridad LevelOne
- Seguridad Unitron
- Seguridad Netatmo
- Seguridad Goobay
- Seguridad Switel
- Seguridad Bticino
- Seguridad Topcraft
- Seguridad First Alert
- Seguridad Sygonix
- Seguridad Nemef
- Seguridad Dahua
- Seguridad Powerfix
- Seguridad Foscam
- Seguridad BRK
- Seguridad Bavaria
- Seguridad Juwel
- Seguridad Hagenuk
- Seguridad Technaxx
- Seguridad Waeco
- Seguridad Logicom
- Seguridad Xavax
- Seguridad Marmitek
- Seguridad Elkron
- Seguridad Orbis
- Seguridad Niko
- Seguridad Gira
- Seguridad Jung
- Seguridad Basetech
- Seguridad Interlogix
- Seguridad Dnt
- Seguridad Trendnet
- Seguridad Fito
- Seguridad Urmet
- Seguridad Iget
- Seguridad Wanscam
- Seguridad Easy Home
- Seguridad Geemarc
- Seguridad Satel
- Seguridad Dymond
- Seguridad Notifier
- Seguridad Friedland
- Seguridad Plustek
- Seguridad Golmar
- Seguridad Grandstream
- Seguridad Batavia
- Seguridad Storage Options
- Seguridad Provision ISR
- Seguridad NetworX
- Seguridad Bitron Video
- Seguridad Eden
- Seguridad Monacor
- Seguridad Zmodo
- Seguridad Velbus
- Seguridad Elro-Flamingo
- Seguridad Electronics Line
- Seguridad One2track
- Seguridad HUMANTECHNIK
- Seguridad Heidemann
- Seguridad Directed Electronics
- Seguridad Oplink
- Seguridad BML
- Seguridad Unitec
- Seguridad Muller
- Seguridad Home8
- Seguridad AVTech - Velleman
- Seguridad Galaxy
- Seguridad Sonic Alert
- Seguridad I-onik
- Seguridad Smartalarm
- Seguridad GE Security
- Seguridad Nor-tec
- Seguridad Entrya
- Seguridad Kopp
- Seguridad Tegui
- Seguridad Stobo
- Seguridad Kompernass
- Seguridad Iiquu
- Seguridad Storex
- Seguridad Powermax
- Seguridad Woonveilig
- Seguridad Mikros
- Seguridad V-Tac
- Seguridad Bolyguard
- Seguridad Indexa
- Seguridad Skytronic
- Seguridad Paradox
- Seguridad Flamingo FA15RF
- Seguridad SecuFirst
- Seguridad BRK DICON
- Seguridad FBII
- Seguridad FlinQ
- Seguridad Dericam
- Seguridad Myfox
- Seguridad Kocom
- Seguridad RISCO Group
- Seguridad SmartHome
- Seguridad Bellman
- Seguridad Protector
- Seguridad I-Tel
- Seguridad Home Protector
- Seguridad Ksenia
- Seguridad Mr Safe
- Seguridad Epine
- Seguridad Inner Range
- Seguridad Dedicated Micros
- Seguridad Visonic
- Seguridad PROmax
- Seguridad Y-cam
- Seguridad Selvag
- Seguridad Voxx
- Seguridad Fracarro
- Seguridad Guardall
- Seguridad Xena
- Seguridad Smanos
- Seguridad One Concept
- Seguridad QuattSecure
- Seguridad NetBotz
- Seguridad Securitas
Últimos Seguridad Manuales
24 Octubre 2024
22 Octubre 2024
21 Octubre 2024
20 Octubre 2024
20 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024
5 Octubre 2024