Jabra GN8000 Manual de Usario
Lee a continuación 📖 el manual en español para Jabra GN8000 (17 páginas) en la categoría Sonido. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/17
User guide
Bedienungsanleitung
Guide d’utilisation
Manual del usuario
Guia do utilizador
Istruzioni d’uso
Gebruikershandleiding
Brugsanvisning
Bruksanvisning
Käyttöohje
Illustrations
UK
D
F
ES
POR
I
NL
DK
S
SF
English
To see the illustrations, first unfold the back cover.
GN 8000 MPA
Connecting GN 8000 MPA
1 Remove the handset cord from the telephone. Connect it to the back of the amplifier into the handset port. Connect the
short cord attached to the back of the amplifier to the telephone, in place of the handset. Connect the headset to the
coiled cord using the QD-connector. Insert the headset stand at the back of the amplifier.
Set-up
2 Lift the top cover and open the battery door on the right side of the amplifier.
3 Install the two AA batteries included with the amplifier.
4 Push the battery door firmly shut until it locks into place.
5 Set the headset/handset switch to headset position.
6 Set the mute switch to talk position.
7 Set the headset volume to mid range.
Checking the system
8 Put on the headset and remove the handset from the telephone. Move the system selector switch slowly through the
settings until you hear a clear dial tone.
Note: positions G, H, and I do not require batteries.
9 Place a call. Adjust the microphone volume control until the other party can hear you clearly. (1 is the softest, 8 is the
loudest)
10 Adjust the headset volume control by sliding the button until you can comfortably hear the other party. If your telephone
has a volume control, set it to the mid to low end of the range for optimum headset performance. To finish the call,
replace the handset in its cradle.
Answering and making calls
11 Put the headset on.
12 Set the headset/handset switch in headset position.
13 Set the mute switch to the talk position.
14 Lift the handset from the telephone to answer or place the call.
15 To end the call, replace the handset on the telephone.
Battery save switch
16 The battery save switch is designed to converse battery power by putting the amplifier into sleep mode when it is sitting
idle for more than two minutes. The circuit design allows the amplifier to awaken under several selectable conditions.
A Battery save feature is on. Amplifier is activated by the receive (incoming) audio.
B Battery save function is on. Amplifier is activated by the receive (incoming) or the transmit microphone) audio.
C Battery save feature is off. Amplifier runs continually. If using this setting, it is recommended that the headset/handset
switch is put in handset position when the headset is not in use in order to save the battery.
Note: A beeping noise in the headset indicates that the batteries are low. Replace both batteries using only AA size
batteries.
Thank you for buying a GN Netcom A/S product.
All GN Netcom A/S products are designed and manufactured in accordance with strict quality standards and should, with a
minimum of maintenance, give many years of satisfactory use.
GN Netcom A/S
This user guide includes the following 10 languages: UK, D, F, E, P, I, NL, DK, S and SF.
©GN Netcom A/S. All Rights Reserved.
This user guide is published by GN Netcom A/S.
The information in this user guide is furnished for informational use only, is subject to change without notice, and should not
be construed as a commitment by GN Netcom A/S. GN Netcom A/S assumes no responsibility or liability for any errors or inac-
curacies that may appear in this user guide.
Written and designed at GN Netcom A/S, Metalbuen 66, 2750 Ballerup, Denmark
Why do I hear an echo in my headset when I talk?
• The microphone volume control may be too high. Lift the amplifier top cover and adjust the microphone volume towards
the left to a lower number.
Why do I hear a beeping noise in my headset?
• A beeping noise in your headset may indicate that the batteries in your amplifier are low. Replace both batteries using
only AA size batteries.
Why doesn’t the on-line indicator light or flash?
• Make sure the headset stand/on-line indicator is plugged all the way into the port on the rear of the amplifier.
• Make sure that the batteries are properly installed.
• Replace the batteries with fresh batteries.
If you have any problems or questions regarding GN 8000, please contact your reseller.
Hereby, GN Netcom as declares that this GN 8000 is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC (www.gnnetcom.com).
On-line Indicator
17 The on-line indicator flashes red when the telephone is off-hook, indicating that you are on the phone. Rotate the on-line
indicator so the light is seen from the best direction for your work area.
Tips
18 The quick disconnect (QD) allows you freedom of movement without removing the headset. If you disconnect your head-
set at the QD during a conversation, you automatically place your caller on hold. Reconnecting the QD resumes the con-
versation.
GN 8050 TCA
Connecting GN 8050 TCA
19 Connect the single 3.5 mm plug to the back of the amplifier in the socket underneath the headset stand. The other end
of the plug has two 3.5 mm plugs. Connect the plug with the speaker icon into the jack of the computer or sound board
marked with a speaker or a headset icon. Connect the plug with the microphone icon to the jack of the computer
marked with the microphone icon.
Computer volume control
20 The computer volume control is located on the lower left side of the amplifier. It is marked with the icon of a computer.
To increase the volume, rotate the control away from you. To decrease the volume, rotate the control toward you.
Telephone/PC switch
21 To use the headset for telephone or PC, set the switch in either telephone or PC position.
Microphone mute switch
The mute switch for the microphone is functional in both telephone mode and computer mode:
22 When the amplifier is in telephone mode and mute function is activated, the microphone is muted to the telephone and
turned on to the computer. When the amplifier is in computer mode and mute function is activated, the microphone is
muted to the computer and to the telephone.
Troubleshooting
Why can’t I hear a dial tone when the headset is on?
• Make sure you have inserted both the headset and handset cords into the appropriate ports.
• Make sure the headset/handset switch is in headset position.
• Make sure that the batteries are properly installed.
• Replace the batteries with fresh batteries.
• You may have the system selector switch in a position that does not correspond with your telephone. Lift the amplifier
top cover and move the system selector switch to another position.
Why does the other party have a hard time hearing me?
• Make sure that the mute switch is in talk position.
• Check the position of the headset microphone boom arm and make sure it is placed approximately 2 cm from
your lower lip.
• The microphone volume control may be too low. Lift the amplifier top cover and adjust the transmit volume
towards the right to a higher number.
• You may have the system selector switch in a position that does not correspond with your telephone. Lift the amplifier
top cover and move the systems selector switch to another position.
Especificaciones del producto
| Marca: | Jabra |
| Categoría: | Sonido |
| Modelo: | GN8000 |
¿Necesitas ayuda?
Si necesitas ayuda con Jabra GN8000 haz una pregunta a continuación y otros usuarios te responderán
Sonido Jabra Manuales
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
Sonido Manuales
- Sonido Kenwood
- Sonido Nokia
- Sonido Olympus
- Sonido Siemens
- Sonido Topcom
- Sonido Yamaha
- Sonido Sony Ericsson
- Sonido Logitech
- Sonido Velleman
- Sonido Korg
- Sonido Speedlink
- Sonido Envivo
- Sonido Profoon
- Sonido Behringer
- Sonido Focusrite
- Sonido Samson
- Sonido Sweex
- Sonido Phonak
- Sonido Zoom
- Sonido Mr Handsfree
- Sonido Geemarc
- Sonido Starkey
- Sonido Iqua
- Sonido Power Dynamics
- Sonido Fender
- Sonido Bellman Symfon
- Sonido Griffin
- Sonido DAP Audio
- Sonido TC Helicon
- Sonido Bellman
Últimos Sonido Manuales
18 Octubre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024
8 Septiembre 2024