JANDY iAquaLink 3.0 Manual de Usario

JANDY No categorizado iAquaLink 3.0

Lee a continuación 📖 el manual en español para JANDY iAquaLink 3.0 (28 páginas) en la categoría No categorizado. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/28
H0669200_REVF
FOR YOUR SAFETY - This product must be installed and serviced
by a contractor who is licensed and qualied in pool equipment by the
jurisdiction in which the product will be installed where such state or
local requirements exist, the maintainer must be a professional with
su󰀩cient experience in pool equipment installation and maintenance
so that all of the instructions in this manual can be followed exactly.
Before installing this product, read and follow all warning notices and
instructions that accompany this product. Failure to follow warning
notices and instructions may result in property damage, personal
injury, or death. Improper installation and/or operation may void the
warranty. Improper installation and/or operation can create unwanted
electrical hazard which can cause serious injury, property damage, or
death. Turn o󰀨 all circuit breakers required in order to
prevent the possibility of electric shock
ATTENTION INSTALLER: This manual contains
important information about the installation, operation
and safe use of this product. This information should
be given to the owner/operator of this equipment.
WARNING
AquaLink® RS Conversion Kit
for Pentair® Enclosures
Installation Instructions
Page 2
Table of Contents
Section 1. Important Safety Instructions 3 ........
Section 2. Package Contents 4 ..........................
2.1 Pool Pump Suction Entrapment
Prevention Guidelines 7 ............................
2.2 Package Contents 9 ..................................
Section 3. Product Compatibility....................10
Section 4. Remove the Pentair®
Control Panel .................................11
4.1 Transformer located on
low voltage side .....................................11
4.2 Transformer located on
high voltage side 14 ..................................
Section 5. Install the AquaLink RS
Conversion Kit 16 ..............................
5.1 Apply the New Wiring Label 16 .................
5.2 New Transformer Installation ............... 17
5.3 Install Conversion Kit.............................18
5.4 Connect Sensor Wires 19 .........................
5.5 Connecting Heater to Low
Voltage Wiring 19 ......................................
5.6 Connecting Auxilliary Equipment
to PCB 20 ..................................................
5.7 Finalize Hardware Installation 20 ..............
5.8 Test the Equipment 21 ..............................
Section 6. Program DIP Switch Settings 21 ......
6.1 DIP Switch Functions 21 ...........................
6.2 DIP Switch Settings 23 .............................
6.3 DIP Switch Settings for
Solar/Heat Pump 24 ..................................
Section 7. Install and Program the iQ20 25 .......
Jandy
®
AquaLink
®
RS Conversion Kit
Page 3
Section 1. Important Safety Instructions
READ AND FOLLOW ALL INSTRUCTIONS
All electrical work must be performed by a licensed electrician and conform to all
national, state, and local codes. When installing and using this electrical equipment,
basic safety precautions should always be followed, including the following:
WARNING
EQUIPMENT UNDER PRESSURE:
Always turn pump off prior to installation
or service. Your pump/filter system is
operated under pressure and the
pressure must be released before
you begin work. Please see your
pump/filter owner’s manual for further
instructions.
WARNING
To reduce the risk of electric shock,
fire or injury, service should only be
attempted by a qualified pool service
professional.
Risk of electric shock: I n s t a l l t h e
power center at least five (5) feet (1.52
m) from the inside wall of the pool and/
or hot tub using non-metallic plumbing.
Canadian installations must be at least
three (3) meters from the water.
WARNING
Risk of electric shock which can
result in serious injury or loss of
life: Before attempting to install or
service, ensure that all power to the
circuit supplying power to the system is
disconnected or turned off at the circuit
breaker. All wiring must be done in
accordance with the National Electrical
Code® (NEC)®, NFPA-70®, including
those in Article 680 - Swimming Pools,
Fountains, and Similar Installations.
In Canada, the Canadian Electrical
Code (CEC), CSA C22.1, must
be followed. All applicable local
installation codes and regulations
must be followed.
ATTENTION: Th e po we r ce nt e r
and the chlorine generator control
center are not to be considered as
suitable for use as service equipment.
Therefore, it is required to have the
appropriate means of disconnection,
circuit isolation, and/or branch circuit
protection installed upstream of the
power/control center
WARNING
To reduce the risk of injury do not
permit children to use this product
unless they are closely supervised at
all times.
WARNING
Risk of Accidental Drowning.
Extreme caution must be exercised
to prevent unauthorized access by
children. To avoid accidents, ensure
that children cannot use a spa or
hot tub unless they are closely
supervised at all times.
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
PREVENT CHILD DROWNING:
Do not let anyone, especially small
children, sit, step, lean or climb on any
equipment installed as part of your
pool’s operational system. Locate the
components of your operational system
at least 1 m (3 ft 3 in) from the pool
so children cannot use the equipment
to access the pool and be injured or
drown.
To reduce the risk of injury, do not remove
the suction fittings of your spa or hot tub.
Never operate a spa or hot tub if the
suction fittings are broken or missing.
Never replace a suction fitting with one
rated less than the flow rate marked on
the equipment assembly.
Installation & Operation Manual

Especificaciones del producto

Marca: JANDY
Categoría: No categorizado
Modelo: iAquaLink 3.0

¿Necesitas ayuda?

Si necesitas ayuda con JANDY iAquaLink 3.0 haz una pregunta a continuación y otros usuarios te responderán


No categorizado JANDY Manuales

JANDY

JANDY Erosion Feeder Manual de Usario

14 Septiembre 2024
JANDY

JANDY TruChlor Erosion Feeder Manual de Usario

14 Septiembre 2024
JANDY

JANDY PSB110 Manual de Usario

13 Septiembre 2024
JANDY

JANDY JS100-SM Manual de Usario

13 Septiembre 2024
JANDY

JANDY SFTM24-2.0 Manual de Usario

13 Septiembre 2024
JANDY

JANDY JS60-SM Manual de Usario

13 Septiembre 2024
JANDY

JANDY SFSM-60 Manual de Usario

13 Septiembre 2024
JANDY

JANDY QT Residential Blower Manual de Usario

13 Septiembre 2024
JANDY

JANDY AquaSwitch Manual de Usario

2 Septiembre 2024
JANDY

JANDY AquaLink Touch Manual de Usario

30 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024