JETI Hicopter 90A opto Manual de Usario

JETI juguetes radiocontrolados Hicopter 90A opto

Lee a continuación 📖 el manual en español para JETI Hicopter 90A opto (1 páginas) en la categoría juguetes radiocontrolados. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
HiCOPTER
The HiCOPTER product line of speed controllers are designed for controlling and regulating
brushless motors that are typically used for powering multicopters. Each speed controller is pre-set
from the factory with settings optimized for use with multi rotor aircraft stabilization systems.
HiCOPTER controllers accept a control signal with a frequency of up to 500Hz. This allows them to
accurately respond to any RPM change required by the control/stabilization unit of the multicopter.
The motor control signal is galvanically (optically) separated from the flight battery in all
HiCOPTER speed controllers. HiCOPTER speed controllers do not require or allow any programming
changes. The propeller brakes are already switched off, the cut-off voltage is pre-set to the lowest
possible level (depending on type) and the motor timing is set automatically by the speed controller. If
you need to change the direction of rotation, simply swap any two of the motor wires.
Install the HiCOPTER speed controller in accordance with the manual instructions for your specific
multicopter type.
Basic parameters of HiCOPTER speed controllers
Type Current
[A]
Input voltage
[V]
Dimensions
[mm]
Weight*
[g]
HiCOPTER 30A opto 30 5-25,2 65x26x9 35
HiCOPTER 40A opto 40 5-25,2 65x26x9 38
HiCOPTER 70A opto 70 5-25,2 70x26x11 45
HiCOPTER 90A opto 90 12-42 65x55x17 100
* weight with the cables
General Principles:
please read these instructions carefully
use only new connectors of good quality, which must be soldered properly to the controller
cables (look out for and remove any remaining flux on the plugs)
flight battery wires can be extended to a maximum overall length of 20 cm
pay attention to the distance between all cables and the receiver antenna the two should be
kept as far apart as possible
only connect the flight batteries to the flight system shortly before the flight and then
disconnect them immediately after landing
when the model is not in use, always disconnect all batteries from the flight system
to prevent the possibility of reverse polarity connections to the controller or batteries use
different types of connectors for each type of connection
do not connect the controller to current supplies other than appropriate battery pack (verify
that your batteries are the correct input voltage and can handle the current load)
to prevent possible injuries by moving mechanical parts of the model (motor, gear box etc.)
always keep in mind that the motor may start unintentionally
check the controller and receiver circuitry each time before switching the system on
install the controllers in the model so that they receive air flow for cooling
Warranty:
We grant a warranty of 24 months from the date of purchase under the premise that the item has
been operated in accordance with these instructions within the specified voltage and currents and that
the controller does not show signs of mechanical damage. The warranty is void if the polarity of the
controller has been reversed or if the controller came in contact with different chemicals or water.
A controller can also be damaged due to following reasons: Use of unsuitable connectors, low
quality soldering joints (plugs), overly long cables between battery controller motor, a
demagnetizated motor, phase interruption (broken or damaged wire) between motor and controller
during operation.
Warranty service and any post warranty service is provided by the distributor or manufacturer.
JETI model s.r.o., Lomená 1530, 742 58 Příbor, Czech Republic www.jetimodel.cz

Especificaciones del producto

Marca: JETI
Categoría: juguetes radiocontrolados
Modelo: Hicopter 90A opto
Color del producto: Wit
Ancho: 157 mm
Profundidad: 157 mm
Altura: 40 mm
Código de seguridad internacional (IP): IP30
Colocación: Tafel
Banda de frecuencia: 2.4 - 2.483, 5.15 - 5.85, 5.15 - 5.25, 5.25 - 5.35, 5.725 - 5.85 GHz
Número de puertos USB 2.0: 1
Número de puertos Ethernet LAN (RJ-45): 1
Consumo de energía (máx.): 12 W
Conexión para adaptador de red: Ja
Modulación: 16-QAM, 64-QAM, 256-QAM, BPSK, CCK, QPSK
LAN Ethernet, velocidades de transferencia de datos: 10,100,1000 Mbit/s
Estándar de red: IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3af
Algoritmos de seguridad compatibles: 802.1x RADIUS, AES, SNMP, SSH, TKIP, WEP, WPA, WPA-PSK, WPA2, WPA2-PSK
Nivel de ganancia de antena (máx.): 3 dBi
Número de usuarios: 256 gebruiker(s)
Temperatura de almacenamiento: -40 - 85 °C
Interno: Nee
Es posible actualizar el firmware: Ja
Gestión basada en web: Ja
Humedad de almacenamiento: 5 - 95 procent
Corriente de salida: 1 A
Abarcando: 12 V
Servidor DHCP: Ja
Velocidad máxima de transferencia de datos: 867 Mbit/s
2,4GHz: Ja
5GHz: Ja
Calidad de servicio (QoS): Ja
VLAN=soporte: Ja
Funciones del identificador de conjunto de servicios (SSID): SSID-broadcast aan/uit
Alimentación a través de Ethernet (PoE): Ja
Funciones de antena: Ingebouwde antenne
Número de canales: 13 kanalen
transmitir potencia: 23 dBmW
Aislamiento inalambrico: Ja
Temperatura de funcionamiento (TT): 5 - 45 °C
Humedad relativa de funcionamiento (VV): 5 - 95 procent
Número de soportes SSID: 16

¿Necesitas ayuda?

Si necesitas ayuda con JETI Hicopter 90A opto haz una pregunta a continuación y otros usuarios te responderán




juguetes radiocontrolados JETI Manuales

juguetes radiocontrolados Manuales

Últimos juguetes radiocontrolados Manuales