JL Audio MX600/3 Manual de Usario

JL Audio sistema de alta fidelidad MX600/3

Lee a continuación 📖 el manual en español para JL Audio MX600/3 (2 páginas) en la categoría sistema de alta fidelidad. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Remote Turn-On

[FR–]

[FR+]

[SUB–]

[SUB+]

[FL–]

[FL+]

[SUB IN]

Sou rce [REM]

Batter y

Fuse

(not included)

[+12V]

[GND]

[FRONT IN]

Thank you for purchasing a JL Audio amplifier for

your sound system.

Your amplifier has been designed and manufactured to exacting

standards in order to ensure years of musical enjoyment. For maximum

performance, we highly recommend that you have

your new amplifier installed by an authorized JL Audio dealer. Your

authorized dealer has the training, expertise and installation equipment

to ensure optimum performance from this product. Should you

decide to install the amplifier yourself, please take the time

to read this manual thoroughly to familiarize yourself

with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this

manual or any aspect of your amplifier’s operation, please contact your

authorized JL Audio dealer for assistance. If you need further assistance,

please call the JL Audio Technical Support Department

at technical@jlaudio.com or call (954) 443–1100 during business hours.

OWNER’S MANUAL

600W 3-Channel Class D System Amplier

What’s Included

(1) Amplifier

(4) Stainless steel mounting screws

(1) User manual

Product Description

This is a three-channel, system amplifier utilizing Class D technology for all

channels.

Installation Applications

This amplifier is designed for operation with 12 volt, negative-ground electrical

systems. Using this product in systems with positive ground and/or voltages

other than 12V may result in damage to the product and will void the warranty.

This product is not certified or approved for use in aircraft.

Safety Considerations

• Whenever possible, mount the amplifier in a dry, well-ventilated location

that does not interfere with other factory installed electronic devices. If a dry

environment is not available, a location that is not exposed to heavy splashing

may be used.

• While this amplifier is designed to be water-resistant, it should never be

submerged under water or subjected to high-pressure water spray.

Do not install where it will be directly exposed to the elements.

• Do not mount the amplifier in the engine compartment or in any areas of

extreme heat.

• Securely mount the amplifier so that it does not come loose in the

event of a collision/sudden jolt or as a result of repeated vibrations during

normal operation.

• Check before drilling to make sure that you will not be drilling into an exterior

panel/hull, fuel tank, gas/brake line, wiring harness, or other vital system.

• Do not run system wiring outside or underneath the vehicle/vessel. This is an

extremely dangerous practice, which can result in severe damage/injury.

• Protect all system wires from sharp edges (metal, fiberglass, etc.) by

carefully routing them, tying them down and using grommets and loom

where appropriate.

• Secure all wiring as needed, using cable ties or wire clamps to protect them

from moving parts and sharp edges.

IPX7 Water Resistance Rating

This product has been tested to withstand immersion in water, up to 1 meter

(3.28 ft.) deep, for up to 30 minutes (with control panel cover properly installed).

Note - while designed to be water resistant, this product should never be

submerged under water for prolonged periods or subjected to activity that

creates pressure on it that exceeds its depth rating.

Installation Procedure/Connections

1. Disconnect the NEGATIVE battery post connection and secure the

disconnected cable to prevent accidental reconnection during installation.

This is an essential safety precaution during installation!

2. Connect the RED power lead to the positive (+12V) battery post. 4 AWG is

the minimum power wire size for this amplifier.

3. An appropriate fuse (sold separately), such as the JL Audio Water-Resistant

Master MAXI™ Fuse Block (XD-MFBW-MAXI), at the main power wire(s) to

the amplifier(s) is vital for vehicle/vessel safety. This fuse must be installed

within 18 inches (45 cm) of the positive battery post connection. If this is

the only device connected to this main wire, use a 60A fuse. Do not install

the fuse until the power wire has been securely connected to the amplifier.

4. Connect the BLACK negative ground lead to a clean, solid metal grounding

point near the amplifier. This can be to metal chassis ground, if available.

If no metal chassis ground is available, it may be necessary to make this

connection to the NEGATIVE battery post. 4 AWG is the minimum ground

wire size for this amplifier. All ground connections (source unit and

amplifiers) should be made at the same location.

5. Connect the BLUE remote turn-on lead to the source unit’s positive (+12V)

remote turn-on output. If your source unit does not have a dedicated

remote turn-on output, the amplifier’s turn-on lead can be connected to

+12V via a switch that derives power from an ignition-switched circuit.

6. Signal Input (Low-Level): Connect the amplifier’s RCA input jacks to the

source unit’s preamp level output jacks.

7. Signal Input (High-Level): If your source unit does not offer preamp level

signal outputs, you can splice the speaker output wires of the source unit

onto a pair of RCA plugs for each input pair or use the JL Audio ECS Speaker

Wire to RCA adaptor (XD-CLRAIC2-SW). Make sure to observe correct

polarity in making “High-Level Input” connections. Failure to do so will result

in a loss of signal (poor performance).

8. Connect the speaker output leads to the corresponding speaker wires.

9. Make necessary adjustments to the filter controls and input sensitivity.

10. The amplifier’s subwoofer output level can be controlled from the front

of the vehicle/vessel with an optional remote level controller (sold

separately). Use the RBC-1 for standard (dry) installations or the M-RBC-1

for applications exposed to moisture. Connect the remote’s plug to the

amplifier’s harness-mounted RJ11 input jack. (Refer to Appendix B)

WARNING! Failure to make safe, tight, high-integrity power connections

can result in fire and extensive damage!

Control Setting Mode / Function

Front / Subwoofer

Input

Voltage

Low RCA/Preamp Level Range (250 mV - 4 V)

High RCA/Preamp or Speaker Level Range (580 mV - 14 V)

Input

Sens. Variable

Adjusts the input stage of each pair of amplifier channels to

match the source unit’s output voltage for maximum clean

output (refer to Appendix A)

Front

Input

Mode

2CH

Applies two channels of input to all three

amplifier channels. Main input signals will be

combined to mono for the subwoofer channel.

Use Front

Inputs Only

4CH

Sends four discrete channels to all four inputs.

L & R Sub Inputs will be combined to mono.

If only one channel of subwoofer signal is

available, we recommend using a Y-adaptor to

feed both Sub Inputs.

Use Front

and Sub

Inputs

Filter

Freq. (Hz) Variable Adjusts the high-pass filter cutoff frequency, variable from

35-300 Hz, 12 dB/Octave

Subwoofer

Output

Polarity

0Normal speaker polarity

180 deg. Polarity reversed 180 degrees

Infrasonic

Filter (Hz) Variable Adjusts the high-pass filter cutoff frequency, variable from

20-40 Hz, 12 dB/Octave

LP Filter

Freq. (Hz) Variable Adjusts the low-pass filter cutoff frequency, variable from

40-400 Hz, 24 dB/Octave

Bass

Boost (dB) Variable

Boost-Only Bass Equalizer: Boost range from 0dB (full-

counterclockwise) to + 12dB (full-clockwise), centered

at 43 Hz.

Control Panel Settings and Adjustments

The amplifier’s settings and controls are located on the bottom panel beneath a

gasketed, protective cover. Remove the four Phillips head screws from the center

panel to access the controls and make adjustments. Replace cover when finished

and mount the amplifier.

Power Connections

Label Wire Color Description

+12V Red Positive (+12V) Power Connection

GND Black Negative (GND) Ground Connection

REM Blue Positive (+12V) Remote Turn-On Input

Inputs

Label Plug Description

FRONT

White RCA Ch. 1 / Front Left Channel Signal Input

Red RCA Ch. 2 / Front Right Channel Signal Input

SUB

White RCA Ch. 3 / Left Subwoofer

Channel Signal Input

Note: L & R Sub Inputs will be

combined to mono. If only one

channel of subwoofer signal is

available, we recommend using a

Y-adaptor to feed both Sub Inputs.

Red RCA Ch. 4 / Right Subwoofer

Channel Signal Input

Outputs

Label Wire Color Description

FL+ White Ch. 1 (+) Positive Front Left Speaker Front Bridged (+)

FL– White/Black (–) Negative Front Left Speaker

FR+ Gray Ch. 2 (+) Positive Front Right Speaker

FR– Gray/Black (–) Negative Front Right Speaker Front Bridged (–)

SUB+ Lt. Blue Ch. 3 (+) Positive Subwoofer Output

SUB– Lt. Blue/Black (–) Negative Subwoofer Output

Optional

Remote Bass

Control Jack RJ11 Input Jack for M-RBC-1 or RBC-1 (each sold separately)

Connections

IPX7

WATER

RESISTANT

Power

Connections

Wiring Diagram

Outputs:

To Speakers

Inputs:

High-Level

< or >

Low-Level

(selectable via

Input Voltage

switch for each

channel pair)

Optional:

M-RBC-1

Remote

Bass Control

(sold separately)

Problem Possible Cause Solution

How to properly set

input sensitivity 

Please refer to Appendix A to set the

input sensitivity for maximum, low-

distortion output.

Amplifier doesn’t

turn on

Faulty fuse Remove fuse and check with continuity

meter. Replace if necessary.

Poor connection

integrity

Check “+12V”, “Ground”, and “Remote”

leads for pinched wires; ensure tight

connections.

Insufficient “Remote”

input

Make sure there is a sufficient +12V

supply at the “Remote” connection; if

not a relay may be required.

Intermittent output,

fluctuates when I tap

on it or hit a bump

Poor connection

integrity

Make sure insulation has been properly

stripped back at connection points for

good contact area.

Make sure input connectors are making

good contact with input jacks of the

amplifier.

Distorted, attenuated,

or popping sound

Faulty speaker

connection (Short

Circuit / Over Current

Protection)

Inspect speaker wires for possible

short-circuit, either together or shorted

to the vehicle’s chassis ground.

Check the nominal load impedance at

the amplifier is equal to or greater than:

Ch.1 & 2: 2 ohms stereo

Ch.1 & 2: 4 ohms bridged

Sub Ch.: 2 ohms

Output shuts off after

a while

Overheating

condition (Thermal

Protection)

Make sure amplifier mounting area has

adequate space for ventilation and heat

dissipation.

No or low subwoofer

output

Remote Bass

Control (optional)

is connected and

turned down

Adjust RBC-1 or M-RBC-1 accordingly

Limited Warranty – Amplifiers (USA)

JL Audio warrants this product to be free of defects in materials and

workmanship for a period of two (2) years from the original date of purchase.

This warranty is not transferrable and applies only to the original purchaser

from an authorized JL Audio dealer. Should service be necessary under this

warranty for any reason due to manufacturing defect or malfunction, JL

Audio will (at its discretion), repair or replace the defective product with new

or remanufactured product at no charge. Damage caused by the following is

not covered under warranty: accident, misuse, abuse, product modification or

neglect, failure to follow installation instructions, unauthorized repair attempts,

misrepresentations by the seller. This warranty does not cover incidental or

consequential damages and does not cover the cost of removing or reinstalling

the unit(s). Cosmetic damage due to accident or normal wear and tear is not

covered under warranty.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the

express warranty as provided herein beginning with the date of the original

purchase at retail, and no warranties, whether express or implied, shall apply

to this product thereafter. Some states do not allow limitations on implied

warranties, therefore these exclusions may not apply to you. This warranty gives

you specific legal rights, and you may also have other rights, which vary from

state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Amplifier Service Facility

freight-prepaid through an authorized JL Audio dealer and must be

accompanied by proof of purchase (a copy of the original sales receipt). Direct

returns from consumers or non-authorized dealers will be refused unless

specifically authorized by JL Audio with a valid return authorization number.

Warranty expiration on products returned without proof of purchase will be

determined from the manufacturing date code. Coverage may be invalidated

as this date is previous to purchase date. Non-defective items received will

be returned freight-collect. Customer is responsible for shipping charges and

insurance in sending the product to JL Audio. Freight damage on returns is not

covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy.

Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered only

by that country’s distributor and not by JL Audio, Inc.

Do not increase any “Input Sens.” setting for any amplifier channel or

channel pair in the system beyond the maximum level established during

this procedure. Doing so will result in audible distortion and possible

speaker damage.

It will be necessary to re-adjust the “Input Sens.” for the affected channels if any

equalizer boost is activated after setting the “Input Sens.” with this procedure. This

applies to any EQ boost circuit, including source unit tone controls or EQ circuits. EQ

cuts will not require re-adjustment.

Target AC Voltage - MX600/3

Nom.

Impedance

Ch.1 & 2

(Stereo)

Ch.1 & 2

(Bridged)

4Ω 17.3 28.3

2Ω 14.1 not recommended

Nom.

Impedance Ch.3/Subwoofer

4Ω 31.6

3Ω 30.0

2Ω 28.3

Troubleshooting

Appendix A:

Input Sensitivity Level Setting

Following the directions below will allow the installer to adjust the input

sensitivity of each amplifier channel pair in just a few minutes using equipment

commonly available in installation bays.

Necessary Equipment

• Digital AC Voltmeter

• CD or file with a sine-wave test tone recorded at 0 dB reference level in the

frequency range to be amplified for that set of channels (50 Hz for subwoofer

channels, 1 kHz for a midrange application). Do not use attenuated test tones

(-10 dB, -20 dB, etc.).

The Nine-Step Procedure

1) Disconnect the speakers from the amplifier’s speaker output

connectors (you need only disconnect one speaker wire).

2) Turn off all processing (bass/treble, loudness, EQ, etc.) on the source

unit, processors (if used) and amplifier. Set the source unit’s fader

control to center position and its subwoofer level control to

3/4 of maximum.

3) Set both “Input Voltage” switches to and turn both “Low” “Input

Sens.” controls all the way down.

4) Set the source unit volume to 3/4 of full volume. This will allow for

reasonable gain overlap with moderate clipping at full volume.

5) Using the Target AC Voltage chart (at right), determine the target

voltage for input sensitivity adjustment according to the nominal

impedance of the speaker system connected to the amplifier outputs.

6) Verify that you have disconnected the speakers before proceeding. Play

a track with an appropriate sine wave (within the frequency range to

be amplified) at 3/4 source unit volume.

7) Connect the AC voltmeter to the speaker output connectors of the

amplifier. Make sure you test the voltage at the correct connectors

(+ and –).

8) Increase the “Input Sens.” control until the target voltage is observed

with the voltmeter. Note: If excessive voltage is measured with the

control set at minimum (full counterclockwise), change the “Input

Voltage” switch setting to “High” and re-adjust.

9) Once you have adjusted the amplifier to its maximum low-distortion

output level, reconnect the speaker(s) and listen to the system. The

“Input Sens.” controls can now be adjusted downward if the amplifier

requires attenuation to achieve the desired system balance.

Specications MX600/3

Rated RMS Power @

14.4V, <1% THD+N

Main @

4 Ω

Main @

2 Ω

Main @ 4 Ω

Bridged

Sub @

4 Ω

Sub @

3 Ω

Sub @

2 Ω

75 W x 2 100 W x 2 200 W x 1 250 W x 1 300 W x 1 400 W x 1

Rated RMS Power @

12.5V, <1% THD+N

Main @

4 Ω

Main @

2 Ω

Main @ 4 Ω

Bridged

Sub @

4 Ω

Sub @

3 Ω

Sub @

2 Ω

50 W x 2 80 W x 2 160 W x 1 200 W x 1 250 W x 1 300 W x 1

Frequency Response 20 Hz - 20 kHz (+0, -1dB), 6.3 Hz - 30 kHz (+0, -3dB)

S/N Ratio, A-weighted,

20 kHz noise

bandwidth

88 dB (Referred to rated power), 68 dB (Referred to 1 W)

Damping Factor >92 / 50 Hz @ 4 Ω, >43 / 50 Hz @ 2 Ω

Input Voltage Range 250 mV - 4 V (Low) or 580 mV - 14 V (High)

Input Mode Switch 2 / 4 Channel

Front High-Pass Filter Freq. Range: 35 - 300 Hz Slope: 12 dB/Octave

Sub Low-Pass Filter Freq. Range: 40 - 400 Hz Slope: 24 dB/Octave

Infrasonic Filter Freq. Range: 20 - 40 Hz Slope: 12 dB/Octave

Sub Output Polarity 0 or 180 degrees

Bass Boost EQ 0 to +12 dB @ 43 Hz

Remote Bass Controller M-RBC-1 or RBC-1 (sold separately)

Input Operating

Voltage 11 - 15 VDC

Min Power/GND Wire 4 AWG

Fuse Rating 60A

Dimensions 9.33 in x 4.50 in x 1.77 in / 237 mm x 114.5 mm x 45 mm

Status LED’s / Protection Circuitry

There are two status indicator lights on the wiring end panel of the amplifier.

1. “POWER” (Green): Lights to indicate that the amplifier is turned on and

operating normally.

2. “PROTECT” (Red): Lights to indicate the amplifier’s protection circuitry

has been triggered to prevent product failure due to any conditions

noted in the chart below. When a protection mode is activated, the

amplifier will shut down to protect its circuitry. For Thermal Protection,

Over Current and Short Circuit conditions, the amplifier will resume

normal operation once the problem is corrected, with the “Protect” LED

turning off. For Over Voltage conditions, the amplifier must be turned

off/on to return to normal operation. Note: connecting the speaker

outputs to impedances lower than 2 ohms (4 ohms bridged) will also

cause this protection mode to activate.

POWER

(Green LED)

PROTECT

(Red LED) Status/Condition Note

ON OFF Normal Operation 

OFF ON Thermal Protection Lasts until temp cools to normal

OFF/ON ON/OFF Over Current Green/Red LEDs alternate for 1 second

OFF ON Short Circuit Possible audible “popping” noise

OFF ON Over Voltage Turn amp off/on to restart

Appendix B

Remote Bass Control

With the optional RBC-1 or M-RBC-1 Remote Bass Control (each sold separately),

you can control the subwoofer volume from the front of the vehicle/vessel.

The remote’s plug connects to the amplifier’s harness-mounted RJ11 input

jack. When connected to the amplifier, the Remote Bass Control operates as

follows. At full counter-clockwise rotation, the audio will mute completely. At full

clockwise rotation the level will be the same as if the remote was not connected

at all. In other words, it operates strictly as a subwoofer level attenuator. This

control will not affect the “Bass Boost” feature of the amplifier. Care should

be taken to securely mount this control in a manner that does not interfere

with vehicle/vessel operation. When setting the amplifier’s input sensitivity,

the Remote Bass Control should be unplugged or at full clockwise rotation

(maximum level).

Especificaciones del producto

Marca:	JL Audio
Categoría:	sistema de alta fidelidad
Modelo:	MX600/3

¿Necesitas ayuda?

Si necesitas ayuda con JL Audio MX600/3 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

sistema de alta fidelidad JL Audio Manuales

JL Audio G1700 Manual de Usario

7 Agosto 2024

JL Audio MX600/3 Manual de Usario

31 Julio 2024

sistema de alta fidelidad Manuales

Últimos sistema de alta fidelidad Manuales

Morel MXT280C Manual de Usario

27 Octubre 2024

Rotel RSP-975 Manual de Usario

27 Octubre 2024

Motu Audio Express Manual de Usario

27 Octubre 2024

Rockford Fosgate HD9813SGU-STAGE2 Manual de Usario

26 Octubre 2024

Thomson MIC123BT Manual de Usario

26 Octubre 2024

Samsung MAX-KC930 Manual de Usario

25 Octubre 2024

Samsung MM-ZL7 Manual de Usario

25 Octubre 2024

Philips FWM996X Manual de Usario

24 Octubre 2024

Sony MHC-RV333D Manual de Usario

21 Octubre 2024

Sony MHC-FR10 Manual de Usario

20 Octubre 2024