Jung DAW360 Manual de Usario
Lee a continuación 📖 el manual en español para Jung DAW360 (8 páginas) en la categoría Cambiar. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
Ceiling automatic switch
Light Management
Ceiling automatic switch
Art.-No.: DAW 360 WW
Ceiling automatic switch
Art.-No.: DAW 360 AL
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
The load is not electrically isolated from the mains even when the device is switched off.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1
(1) Flush-mounted insert
(2) Motion detector cover
(3) Adjuster sens
(4) Adjuster time
(5) Adjuster lux
(6) Brightness sensor
(7) LED display, behind the lens
(8) Lens
(9) Decor ring
(10) Push-on cover
1/8
82563813
J:0082563813 17.11.2011
3 Function
Intended use
- Automatic switching of lighting depending on the heat motion and ambient brightness.
- Operation with concealed insert for dimming, switching or extension insert, 3-wire
- Ceiling installation on flush-mounted insert
Product characteristics
- Run-on time, sensitivity and brightness threshold settable
- Test operation for checking the detection area
- Short-time operation to control signal encoders
- Dimming phase in combination with dimming insert
- Saving a switch-on brightness with dimming inserts
- Dimming lights with dimming inserts
- Manual switch-on possible via extension insert, 2-wire, or installation button
- 78 lens segments in 5 recording levels
- Extension of the detection area in combination with the 3-wire extension insert
- Detection area can be limited using push-on cover
Automatic operation
The controller detects heat motions of people, animals and objects.
- The light is switched on if a person enters the monitored detection area and the brightness
is below the set threshold.
- The light is switched off if no more movement is detected in the detection area and the
follow-up time has elapsed.
Dimming phase with dimming insert
If the motion detector cover is fitted on a dimming insert, then when the run-on time elapses the
lighting is dimmed to minimum brightness and then switched off. The time from the start of
dimming to switching-off is always approx. 30 s. If a motion is detected during the dimming
phase, the motion detector switches the lighting to the stored switch-on brightness again.
Behaviour in case of a mains failure
- Less than 0.2 seconds: the old switching position is restored after mains return.
- 0.2 seconds to approx. 2 seconds: when the power returns, the lighting is switched on
again for the run-on time. Each detected movement restarts the run-on time again.
- Longer than 2 seconds: when the power returns, the motion detector carries out a brief
calibration process. Then the lighting remains switched on for the run-on time. Each
detected movement restarts the run-on time again.
LED display (7)
Main device Extension
LED lights up during the calibration process. LED lights up during the calibration process.
LED lights up when a motion is detected if the
lighting is switched off and the brightness is
not below the brightness threshold.
LED lights up when a motion is detected.
4 Operation
Switching on the light
A 2-wire extension or an installation button, NO contact is connected.
o Press extension or installation button.
Light is switched on independently of the brightness, with a dimming insert to switch-on
brightness. Automatic mode is active.
i After manual switch-on the run-on time is at least 2 minutes.
i Manual switch-on is not possible.
2/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch
Dimming light with dimming insert
The light can be dimmed using a 2-wire extension. The light remains at the dimmed value until
the run-on time has elapsed.
o Press 2-wire insert at top or bottom until the desired brightness is reached.
i An installation button cannot be used for dimming.
Saving a switch-on brightness with dimming insert
A 2-wire extension can be used to save any desired switch-on brightness. In the state as
supplied the switch-on brightness is set to maximum.
The saved switch-on brightness is retained in the event of a power failure.
o Set the required brightness.
o Press 2-wire extension for longer than 3 seconds over entire surface.
Switch-on brightness is saved. For confirmation the lighting switches off briefly and then on
again to the saved switch-on brightness.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Selecting the installation location
Figure 2: Sensor window and detection area
The motion detector has a detection area of 360° (figure 2). The diameter of the detection area
depends on the installation height and the direction of motions of persons in the detection area
(figure 3). At an installation height of 3 m the maximum diameter on the floor is approx. 12 to 20
m.
3/8
82563813
J:0082563813 17.11.2011
Light Management
Ceiling automatic switch
Especificaciones del producto
| Marca: | Jung |
| Categoría: | Cambiar |
| Modelo: | DAW360 |
¿Necesitas ayuda?
Si necesitas ayuda con Jung DAW360 haz una pregunta a continuación y otros usuarios te responderán
Cambiar Jung Manuales
2 Octubre 2024
20 Septiembre 2024
14 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
4 Septiembre 2024
4 Septiembre 2024
Cambiar Manuales
- Cambiar Philips
- Cambiar Panasonic
- Cambiar Honeywell
- Cambiar Yamaha
- Cambiar Abus
- Cambiar Alcatel
- Cambiar Alecto
- Cambiar Apc
- Cambiar Alpine
- Cambiar Ansmann
- Cambiar Edimax
- Cambiar Intermatic
- Cambiar Flamingo
- Cambiar Brennenstuhl
- Cambiar Hikvision
- Cambiar Generac
- Cambiar Silvercrest
- Cambiar Nedis
- Cambiar Pyle
- Cambiar Asus
- Cambiar Eminent
- Cambiar Renkforce
- Cambiar Vivanco
- Cambiar TP Link
- Cambiar Manhattan
- Cambiar Black Box
- Cambiar Elro
- Cambiar Victron Energy
- Cambiar KlikaanKlikuit
- Cambiar Ei Electronics
- Cambiar Tripp Lite
- Cambiar DataVideo
- Cambiar Schneider
- Cambiar Theben
- Cambiar Elektrobock
- Cambiar Chamberlain
- Cambiar Sylvania
- Cambiar Velleman
- Cambiar Tork
- Cambiar Techly
- Cambiar Emerson
- Cambiar Totolink
- Cambiar Vemer
- Cambiar Profile
- Cambiar Cisco
- Cambiar Matrox
- Cambiar Steren
- Cambiar Perel
- Cambiar Engenius
- Cambiar Plantronics
- Cambiar IFM
- Cambiar Digitus
- Cambiar Kathrein
- Cambiar AV:link
- Cambiar Belkin
- Cambiar Linksys
- Cambiar Dahua Technology
- Cambiar Audiovox
- Cambiar Netgear
- Cambiar LevelOne
- Cambiar Kaiser
- Cambiar QNAP
- Cambiar Boss
- Cambiar Shimano
- Cambiar Merten
- Cambiar Goobay
- Cambiar Hager
- Cambiar Mercusys
- Cambiar Chacon
- Cambiar Elation
- Cambiar Sygonix
- Cambiar Planet
- Cambiar ZyXEL
- Cambiar Rex
- Cambiar Clas Ohlson
- Cambiar Powerfix
- Cambiar Tesla
- Cambiar EVE
- Cambiar D-Link
- Cambiar Tenda
- Cambiar UPM
- Cambiar Finder
- Cambiar Marmitek
- Cambiar Delta Dore
- Cambiar Ubiquiti Networks
- Cambiar EBERLE
- Cambiar Grasslin
- Cambiar Omnitronic
- Cambiar Eaton
- Cambiar CyberPower
- Cambiar Basetech
- Cambiar Trendnet
- Cambiar Mikrotik
- Cambiar WHALE
- Cambiar ATen
- Cambiar Fibaro
- Cambiar RGBlink
- Cambiar Gefen
- Cambiar Nexa
- Cambiar PAC
- Cambiar Wentronic
- Cambiar Dormakaba
- Cambiar Adder
- Cambiar Wago
- Cambiar Homematic IP
- Cambiar Monoprice
- Cambiar Tiptel
- Cambiar OSD Audio
- Cambiar SPC
- Cambiar Crestron
- Cambiar Unify
- Cambiar ORNO
- Cambiar Toolcraft
- Cambiar Berker
- Cambiar Electro Harmonix
- Cambiar Grandstream
- Cambiar Mercury
- Cambiar Provision ISR
- Cambiar Monacor
- Cambiar PCE
- Cambiar Logilink
- Cambiar Smart-AVI
- Cambiar StarTech.com
- Cambiar SIIG
- Cambiar Advantech
- Cambiar IOGEAR
- Cambiar Merlin Gerin
- Cambiar Micro Connect
- Cambiar Extron
- Cambiar KanexPro
- Cambiar Blustream
- Cambiar Avocent
- Cambiar Shelly
- Cambiar Intellinet
- Cambiar Ebode
- Cambiar Lancom
- Cambiar Robbe
- Cambiar B-tech
- Cambiar Speaka
- Cambiar Kopp
- Cambiar Vimar
- Cambiar Kemo
- Cambiar GAO
- Cambiar H-Tronic
- Cambiar Legrand
- Cambiar Kraus & Naimer
- Cambiar Noble
- Cambiar Intertechno
- Cambiar Ecler
- Cambiar Inverto
- Cambiar Triax
- Cambiar Rule
- Cambiar Kramer
- Cambiar CYP
- Cambiar Suevia
- Cambiar Phoenix Contact
- Cambiar Seuthe
- Cambiar Maclean Energy
- Cambiar SmartAVI
- Cambiar Cudy
- Cambiar Heitronic
- Cambiar Lindy
- Cambiar SEC24
- Cambiar Cooking Performance Group
- Cambiar Ernitec
- Cambiar Atlona
- Cambiar Adviti
- Cambiar Flic
- Cambiar IB Connect
- Cambiar Liberty
- Cambiar Hamlet
- Cambiar Paladin
- Cambiar Equip
- Cambiar Noark
- Cambiar Vivolink
- Cambiar Cambium Networks
- Cambiar 2USB
- Cambiar Roline
- Cambiar KVM-TEC
- Cambiar AMX
- Cambiar BZBGear
- Cambiar STI
- Cambiar Epiphan
- Cambiar Mach Power
- Cambiar Axing
- Cambiar Juniper
- Cambiar Raritan
- Cambiar ConnectPro
- Cambiar SunBriteTV
- Cambiar Atlantis Land
- Cambiar GEV
- Cambiar Pizzato Elettrica
- Cambiar Baco
- Cambiar SEADA
- Cambiar Doepke
- Cambiar Comet
- Cambiar IPGARD
- Cambiar CSL
- Cambiar Setti+
- Cambiar PureLink
Últimos Cambiar Manuales
27 Octubre 2024
27 Octubre 2024
22 Octubre 2024
22 Octubre 2024
22 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024