Kenwood DDX418 Manual de Usario

Kenwood reproductor de DVD DDX418

Lee a continuación 📖 el manual en español para Kenwood DDX418 (20 páginas) en la categoría reproductor de DVD. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/20
LVT2199-005A (KN/RN)© 2010 Kenwood Corporation All Rights Reserved.
DDX418
DDX4048BT
DDX318
DDX3048
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
MONITEUR AVEC RÉCEPTEUR DVD
MANUEL D'INSTALLATION
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACIÓN
2 DDX418/DDX4048BT/DDX318/DDX3048
Accessories
1
..........1
2
..........1 (2m: 6.5 ft)
3
..........6
4
..........6
5
..........1
6
..........2
7*1
..........1 (3m: 9.8 ft)
*1 DDX418/ DDX4048BT
only.
Installation Procedure
1 To prevent a short circuit, remove the key
from the ignition and disconnect the -
battery.
2 Make the proper input and output wire
connections for each unit.
3 Connect the speaker wires of the wiring
harness.
4 Connect the wiring harness wires in the
following order: ground, battery, ignition.
5 Connect the wiring harness connector to
the unit.
6 Install the unit in your car.
7 Reconnect the - battery.
8 Press the reset button.
9 Perform the Initial Setup. (Refer to the
Instruction Manual.)
2WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
After the Installation
After the installation, perform the Initial Setup
by referring to the instruction manual.
¤
• Mounting and wiring this product requires
skills and experience. For best safety, leave the
mounting and wiring work to professionals.
• Make sure to ground the unit to a negative 12V
DC power supply.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
• If the power is not turned ON ("Miswiring
DC Offset Error", "Warning DC Offset Error" is
displayed), the speaker wire may have a short-
circuit or touched the chassis of the vehicle and
the protection function may have been activated.
Therefore, the speaker wire should be checked.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a power
source that can be turned on and off with the
ignition key. If you connect the ignition wire to
a power source with a constant voltage supply,
such as with battery wires, the battery may be
drained.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
Accessories/ Installation Procedure
English 3
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
• Insulate unconnected wires with vinyl tape or
other similar material. To prevent a short circuit,
do not remove the caps on the ends of the
unconnected wires or the terminals.
• Connect the speaker wires correctly to the
terminals to which they correspond. The unit may
be damaged or fail to work if you share the -
wires or ground them to any metal part in the car.
• When only two speakers are being connected
to the system, connect the connectors either to
both the front output terminals or to both the
rear output terminals (do not mix front and rear).
For example, if you connect the connector +
of the left speaker to a front output terminal, do
not connect the connector to a rear output -
terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30°
or less.
• Do not press hard on the panel surface when
installing the unit to the vehicle. Otherwise scars,
damage, or failure may result.
• This unit has the cooling fan to decrease the
internal temperature. Do not mount the unit
in a place where the cooling fan of the unit are
blocked. Blocking these openings will inhibit the
cooling of the internal temperature and result in
malfunction.
Cooling fan
DDX418/ DDX4048BT only
• Install the Bluetooth adaptor (KS-UBT1) besides
the place enclosed by the metal.
Bluetooth adaptor (KS-UBT1)

Especificaciones del producto

Marca: Kenwood
Categoría: reproductor de DVD
Modelo: DDX418

¿Necesitas ayuda?

Si necesitas ayuda con Kenwood DDX418 haz una pregunta a continuación y otros usuarios te responderán


reproductor de DVD Kenwood Manuales

Kenwood

Kenwood DVF-5500-S Manual de Usario

4 Octubre 2024
Kenwood

Kenwood DVF-5500-B Manual de Usario

16 Septiembre 2024
Kenwood

Kenwood DVF-3400-S Manual de Usario

21 Agosto 2024
Kenwood

Kenwood DDX26BT Manual de Usario

18 Agosto 2024
Kenwood

Kenwood Excelon DDX9906XR Manual de Usario

16 Agosto 2024
Kenwood

Kenwood DDX418 Manual de Usario

15 Agosto 2024
Kenwood

Kenwood DVF-5400-S Manual de Usario

24 Julio 2024
Kenwood

Kenwood DVR-505 Manual de Usario

13 Julio 2024

reproductor de DVD Manuales

Últimos reproductor de DVD Manuales

LG

LG DVX9500 Manual de Usario

23 Octubre 2024
LG

LG HT302SDW Manual de Usario

23 Octubre 2024
LG

LG LH-T6547 Manual de Usario

23 Octubre 2024
LG

LG LH-T6245 Manual de Usario

23 Octubre 2024
LG

LG LH-W5100 Manual de Usario

23 Octubre 2024
LG

LG LH-T361SE Manual de Usario

23 Octubre 2024
LG

LG HT552PH Manual de Usario

23 Octubre 2024
LG

LG LH-T460TF Manual de Usario

23 Octubre 2024
LG

LG DVD4750 Manual de Usario

23 Octubre 2024
Toshiba

Toshiba sd191 Manual de Usario

22 Octubre 2024