Kenwood DNX7032 Manual de Usario
Kenwood
Dispositivo GPS
DNX7032
Lee a continuación 📖 el manual en español para Kenwood DNX7032 (33 páginas) en la categoría Dispositivo GPS. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/33
© B54-4653-00/00 (KW/RW)
DNX7120
DDX712
DDX7032
GPS NAVIGATION SYSTEM
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
SYSTÈME DE NAVIGATION GPS
MONITEUR AVEC RÉCEPTEUR DVD
MANUEL D’INSTALLATION
SISTEMA DE NAVEGACIÓN GPS
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACIÓN
2 | DNX7120/DDX712/DDX7032
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........1
8
..........1
9
..........6
0
..........6
!
..........1
@
DNX7120 only ..........1
#
DNX7120 only
..........1
$
DNX7120 only
..........1
Accessories
English | 3
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
• If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Acquiring GPS Signals
The first time you turn on the DNX7120, you must
wait while the system acquires satellite signals for
the first time. This process could take up to several
minutes. Make sure your vehicle is outdoors in an
open area away from tall buildings and trees for
fastest acquisition. After the system acquires satellites
for the first time, it will acquire satellites quickly each
time thereafter.
¤
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
• Make sure to ground the unit to a negative 12V DC power
supply.
• Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
• If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
• Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
• If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
• Use a commercially available conversion connector if the
connector does not fit in the vehicle connector.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
• Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
Especificaciones del producto
| Marca: | Kenwood |
| Categoría: | Dispositivo GPS |
| Modelo: | DNX7032 |
¿Necesitas ayuda?
Si necesitas ayuda con Kenwood DNX7032 haz una pregunta a continuación y otros usuarios te responderán
Dispositivo GPS Kenwood Manuales
11 Septiembre 2024
17 Agosto 2024
17 Agosto 2024
16 Agosto 2024
8 Agosto 2024
31 Julio 2024
26 Julio 2024
23 Julio 2024
Dispositivo GPS Manuales
- Dispositivo GPS Samsung
- Dispositivo GPS LG
- Dispositivo GPS Fysic
- Dispositivo GPS Garmin
- Dispositivo GPS Alpine
- Dispositivo GPS Hitachi
- Dispositivo GPS Nedis
- Dispositivo GPS Bushnell
- Dispositivo GPS Orbit
- Dispositivo GPS Humminbird
- Dispositivo GPS Polar
- Dispositivo GPS IFM
- Dispositivo GPS Magellan
- Dispositivo GPS Ventus
- Dispositivo GPS Mio
- Dispositivo GPS Uniden
- Dispositivo GPS Audiovox
- Dispositivo GPS QStarz
- Dispositivo GPS First Alert
- Dispositivo GPS TomTom
- Dispositivo GPS Lezyne
- Dispositivo GPS Navman
- Dispositivo GPS Teltonika
- Dispositivo GPS Teasi
- Dispositivo GPS Tile
- Dispositivo GPS Spotter
- Dispositivo GPS Falk
- Dispositivo GPS Kogan
- Dispositivo GPS Tractive
- Dispositivo GPS Navilock
- Dispositivo GPS Tragant
- Dispositivo GPS Nedsoft
- Dispositivo GPS Canyon
- Dispositivo GPS Trackilive
- Dispositivo GPS Avidyne
- Dispositivo GPS Hamlet
- Dispositivo GPS Moki
- Dispositivo GPS Lantronix
- Dispositivo GPS LifeWatcher
- Dispositivo GPS PAJ GPS
- Dispositivo GPS GlobalSat
- Dispositivo GPS Cobblestone
Últimos Dispositivo GPS Manuales
27 Octubre 2024
7 Octubre 2024
5 Octubre 2024
4 Octubre 2024
4 Octubre 2024
3 Octubre 2024
3 Octubre 2024
2 Octubre 2024
22 Septiembre 2024
18 Septiembre 2024