Keurig K-SELECT Manual de Usario

Lee a continuación 📖 el manual en español para Keurig K-SELECT (6 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
Get the most from your
new Keurig® brewer
K-SELECT
Use & Care Guide
Remove packing tape from
brewer and plug into a grounded
outlet.
Place a large mug (12oz.
minimum) on the drip tray plate.
Remove the water reservoir lid, then lift
the reservoir straight up to remove it.
If you have a Keurig® Water Filter,
install it now. Refer to your Water
Filter Starter Kit for instructions.
Rinse reservoir with fresh water and
fill to the fill line.MAX
Replace water reservoir, making sure the
lock tab engages with the brewer. Replace lid.
NOTE: Do not use distilled water.
Press power button — the green power
light and Auto Off light will illuminate.
The brewer will automatically begin
heating the water. This will take about 3
minutes. Once the heating sound stops,
the brewer is ready.
Lift and lower the handle. Do not
insert a K-Cup® pod. The four brew
buttons and the Strong button will
blink.
Press the small cup button to start
a cleansing brew. Pour the hot water
into the sink.
The one-time setup process is now
complete and you are ready to brew!
1 2
3 4
Before You Brew
Brew Your First Cup
Lift the handle and place a K-Cup®
pod in the K-Cup® pod holder. Lower
the handle completely to close the lid.
Do not remove the foil lid on the
K-Cup® pod.
Place a mug on the drip tray
plate. If using a travel mug,
remove the drip tray and place
the mug on the drip tray base.
NOTE: Between brew cycles, the brewer may take about a
minute to reheat.
Select your brew size for bolder coffee,
press the Strong button before selecting
your brew size. The brew size and Strong
button, if selected, will remain illuminated
while brewing – about 1 minute.
The brewer will be ready to brew another
cup in about a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift
and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the K-Cup® pod
holder. To avoid injury, do not lift the handle during the brewing process.
Brewer Features
Strong Brew kicks up your coffee’s strength and intensity. For bolder coffee, press
the Strong button before selecting your brew size.
Smart Start heats then brews in one simple process. No need to wait for the brewer
to heat before selecting brew size. Power on your brewer, place mug, insert a K-Cu
pod, and lower the handle. Then, select your brew size. The brewer will heat, then
automatically begin brewing.
Auto Off automatically turns your brewer off 2 hours after the last brew for energy
savings.
To disable the Auto Off feature:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong and the 10oz. Large Mug buttons for 3 seconds the green Auto Off light will turn off.
3. Power the brewer on the green Auto Off light will no longer be illuminated.
To enable the Auto Off feature, repeat steps 1-3. The green Auto Off light will
illuminate.
High Altitude Brewing: To ensure your brewer works properly at higher altitudes
(5,000 feet) please follow these brewing instructions and enable the High
Altitude Brewing Mode on your brewer.
Brewing Instructions - While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod
holder until the bottom of the K-Cup® pod is punctured by the exit needle.
To enable High Altitude Brewing Mode:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong 8oz. Small Mug and buttons for 3 seconds- both lights will blink 3 times to
confirm that the High Altitude Brewing Mode has been enabled.
To disable High Altitude Brewing Mode:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong 8oz. Small Mug and buttons until the lights are no longer illuminated.
56
7
Travel Mug
12oz.
Large Mug
10oz.
Small Cup
6oz.
Small Mug
8oz.
St rong
Aut o Of f
Add Wat er
Des cale
Stron g
Auto Off
Ad d Water
Descale
MAX.
Stron g
Auto Off
Ad d Water
Descale
Stro ng
Auto Off
Add Water
Descale
Stro ng
Auto Off
Add terWa
Descale
Strong
Auto Off
Add terWa
Descale
Plug & Place Rinse & Fill
Power On Lift & Lower
Place Mug
Lift & Insert
Brew & Enjoy
Strong
Brewer Exterior
Keep your Keurig® brewer looking its
best by cleaning the exterior from
time to time. Just clean with a damp,
soapy, lint-free, non-abrasive cloth.
Never immerse the brewer in water or
other liquids.
Drip Tray
The drip tray can hold up to 8 ounces
of overflow and should be emptied
and cleaned occasionally. To remove,
slide it toward you, keeping it level
to avoid spilling. Clean in dishwasher
(top rack only) or rinse and clean with
a damp, soapy, lint-free, non-abrasive
cloth.
Water Reservoir & Reservoir Lid
The water reservoir lid and water
reservoir should be cleaned
periodically. Clean in a dishwasher
(top rack only) or hand wash. To
hand wash, use a damp, soapy, non-
abrasive cloth. Rinse the reservoir
thoroughly after cleaning. This will
ensure that no cleaning solutions
remain in the area as they may
contaminate the water supply. After
rinsing, fill the reservoir with clean water and return it to the
brewer. Do not dry the inside of the water reservoir with a
cloth as lint may remain. If needed, repeat above procedures.
NOTE: If you are using a water filter inside the water reservoir, remove it before cleaning.
Caring for your Brewer
K-Cup® Pod Holder
To remove the K-Cup® pod holder from
the brewer, lift the handle and grasp
the top of the K-Cup® pod holder
with one hand while pushing up on
the bottom of the K-Cup® pod holder
from underneath with the other until
it releases. After cleaning, align the
K-Cup® pod holder with the opening
using the two front ribs as a guide
and snap into place from the top.
CAUTION: There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the
bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
Funnel
The funnel can be removed from the
K-Cup® pod holder by pulling on it until
it pops off. To replace it, just snap it
back onto the K-Cup® pod holder.
Exit Needle
Remove the pod holder assembly and
detach the funnel. Locate the exit
needle on the inside bottom of the
K-Cup® pod holder. Insert a straightened
paper clip into the exit needle to loosen
the clog and push it out.
Entrance Needle
Lift the brewer handle and locate the entrance needle on the
underside of the lid. To clean both holes in the needle, hold
the brewer handle in the upward position and with your other
hand, carefully insert a straightened paper clip into both
holes. Gently move it around to loosen any coffee grounds.
Lower the handle completely and run two water-only brew
cycles. Do not insert a K-Cup® pod.
TIP: Refer to support.Keurig.com for video instructions on cleaning the entrance/exit needles.
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Stro ng
Auto O ff
Add terWa
Descale
MAX.
Strong
Auto Off
Add Water
Descale
Stron g
Auto Off
Ad d terW a
Descale

Especificaciones del producto

Marca: Keurig
Categoría: No categorizado
Modelo: K-SELECT

¿Necesitas ayuda?

Si necesitas ayuda con Keurig K-SELECT haz una pregunta a continuación y otros usuarios te responderán




No categorizado Keurig Manuales

No categorizado Manuales

Últimos No categorizado Manuales