Kicker ZX 300.1 Manual de Usario

Lee a continuación 📖 el manual en español para Kicker ZX 300.1 (28 páginas) en la categoría Radio del coche. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/28
ZX AMPLIFIER
ZX300.1
ZX400.1
ZX500.1
ZX750.1
English Version
Versión Español
Amplificador del la Serie ZX.1
Deutsche Version
Stereoverstärker der ZX.1-Serie
Version Francaise
Amplificateur de série ZX.1
LIVIN’ LOUD
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 12011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1 11/5/2010 1:22:27 PM11/5/2010 1:22:27 PM
2ZX AMPLIFIERS
ZX.1-SERIES AMPLIFIERS Owner’s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the ZX
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX300.1 ZX400.1 ZX500.1 ZX750.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Length 13-1/2”
(342mm)
10-1/4”
(260mm)
12”
(305mm)
14-11/16
(373mm)
Selectable Electronic Crossover Lo-pass,
80Hz,
24dB/octave
Variable lo-pass 50–200Hz, 24dB/octave
Bass Boost +12dB, on/off,
40Hz
Variable 0–18dB @ 40Hz
Frequency Response ± 1dB 25Hz–20kHz 25Hz–200Hz
Specifi cations common to all models:
Height 2-1/8” (54mm)
Width 9-5/8” (244mm)
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Subsonic Filter 24dB/octave, fi xed @ 25Hz
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 22011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX300.1 1 x 60 Ampere 8 Gauge PK8, CK8, ZCK8
ZX400.1 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
ZX500.1 1 x 80 Ampere 4 Gauge PK4, CK4, ZCK4
ZX750.1 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
protection LED
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 32011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM

Especificaciones del producto

Marca: Kicker
Categoría: Radio del coche
Modelo: ZX 300.1

¿Necesitas ayuda?

Si necesitas ayuda con Kicker ZX 300.1 haz una pregunta a continuación y otros usuarios te responderán




Radio del coche Kicker Manuales

Radio del coche Manuales

Últimos Radio del coche Manuales