Kicker ZX150.2 Manual de Usario
Kicker
Radio del coche
ZX150.2
Lee a continuación 📖 el manual en español para Kicker ZX150.2 (10 páginas) en la categoría Radio del coche. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/10
ZX
STEREOAMPLIFIER
ZX ZX ZX150 ,.2 200 ,.2 250.2
©2006 Stillwater Designs
English Version
Versión spañolE
Amplificador del la erie ZX.S 2
Manual del Propietario
Deutsche Version
S 2 Stereoverstärker der ZX. - erie
Benutzerhandbuch
Version Française
Amplificateur de série ZX.2
Manuel d'utilisation
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level)
interconnect cable to feed the audio signal
to the amplifier. Only use speaker wire
(high-level) inputs if your source unit does
not have RCA type outputs. Either input
method will provide a low-level output
signal at the RCA output, which effectively
passes the audio signal to another
amplifier or component (P.A.S.T.). Keep
the RCA cable away from factory wiring
harnesses and other power wiring. If you
need to cross this wiring, cross it at a 90
degree angle.
Install a fuse within 18” (45cm) of the
battery and in-line with the power cable
connected to your amplifier. If you ever need to remove the amplifier from the vehicle after it has been
installed, the ground wire should be the last wire disconnected from the amplifier--just the opposite as
when you installed it. See the chart below for power and ground wire size, and fusing
recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series amplifier.
Two Channel Operation ( tereo) SThese ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
S O S S Stereo and Mono peration imultaneously ( AM ) The ZX.2 series amplifiers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo
simultaneously with the use of passive crossovers. See Figure 4.
INSTALLAT OI N
ZX.2AMPLIFIER
ZX ZX ZX150.2 /200.2 /250.2
TwoChannelModels:
ZX.2SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
SOURCE UNIT
killers trk7“on Top”
INPUT
RL
L -+L- R+ R
OUT UTP
RL
H E EI-L V L
INPUT
+ +- -O OFF HI L
X VO ER
Model FuseZX150.2 25APowerG d 8rounWire GA
Model FuseZX200.2 30APowerG d 8rounWire GA
Model FuseZX250.2 40APowerG d 8rounWire GA
24"
Or Less
(60cm)
G droun
+
_
+
_
R-
R+
L-
L+
Rem teo
Turn-On
Battery
+12V Fuse
Right Speaker
Left Speaker
18"
Or Less
Signal O t (Pu . . .A S T.)
(45cm)
Signal In
Minim ance f 2 peratium imped o ohms per channel in stereo o on
Rem teo
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
Minim m impe ance f hms when in bri ge peratiu d o 4 o d d o on
R-
R+
L-
L+
+
_
M no o
Speaker
Signal Out (P. . .A S T.)
Signal In
24"
Or Less
(60cm)
G droun
24"
Or Less
(60cm)
G droun
+
_
+
_+
_
HIGH PASS
CROSSOVER
HIGH PASS
CROSSOVER LOW
PAS S
CROSS-
OVER
Left Speaker
Right Speaker
M no o
Speaker
R-
R+
L-
L+
Remote
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
Minim m impe ance f hms m an hms per channel inu d o 4 o o ond 2 o
stere sim ltane se ss verso u ously with the u of passive cro o
Signal Out (P. . .A S T.)
Signal In
23
Figure 1
Figure 2
Figure 3
Figure 4
U u ,se o only ne type of signal inp t to the amplifier
either RCA Cable Speaker or Wire
RCA Cable
(Low-Level)
Input
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level t) Inpu
Left +
Left -
Right -
Right +
C AONFIGUR T OI N
RCA Cable
(Low-Level)
O tutpu
Cross ver Switcho
Signal uO t
(P. . . .A S T )
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Operation
Your Kicker ZX.2 series amplifier has three rotary controls on top and one switch on the end-panel.
Before turning on the system for the first time, turn the three rotary controls on the top of the amplifier
to the full counter-clockwise position.
1. CrossoverSwitch The crossover switch on the end-panel is for setting the internal crossover. In
the OFF position the amplifier passes
a full-range signal to the speakers.
Use the LO position when connected
to a subwoofer. The HI position
should be selected when connected
to speakers, which you do not want
to receive any sub-bass information.
Never change the crossover
"OFF/HI/LO" switch setting with the
audio system on! See Figure 1.
2. InputGainControl The input gain control is not a volume control. It matches the output of the
source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can
hear audible distortion, then turn it down a little.
3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB
at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the
input gain control to avoid clipping the amplifier.
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.
TroubleShooting
If your amplifier does not appear to be working, check the obvious things first such as blown fuses,
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
are two LEDs on the top of your Kicker ZX series amplifier, one green and one red. When the green
LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns off and
the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.
Green LE ,D off no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power
terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)
3) Check for reversed power and ground connections 4) Ground terminal, for proper conductivity.
Green LE ,D on no output? Check the following: 1) RCA connections 2) Test speaker outputs
with a “known” good speaker. 3) Substitute source unit with a “known” good source unit.
4) Check for a signal in the RCA cable feeding the amplifier with the “AC” test position selected
on the VOM meter.
R E ,ed L D on no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow
around the amplifier. 2) Amplifier shuts down only while vehicle is running. Voltage protection
circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have the
vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels.
Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended
impedance.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes
sides then you have a bad speaker cable, passive crossover network and/or speaker.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
Poor stereo image or reduced bass response? Check system phasing by turning the balance
control from left to right. If there is more bass output when turned to either side, then check your
speaker wiring, passive crossover networks and speaker terminals for proper positive and negative
connections. Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s); if the bass improves, the speaker was out of phase.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be
available. The Kicker Coaxial and Component speakers are rated at four ohms (some DC Resistances
may be as low as 3 ohms) and work with any amplifier designed to operate at a four ohm load. If you
want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the
speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the
thermal load at the amplifier. This may prevent an amplifier from shutting down, due to over-current
protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are
correct. Improper connections can result in blown amplifier fuses as well as the failure of other critical
systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the
Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the
SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab,
choose the subject you are interested in, and then download or view the corresponding information.
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or
specific questions.
Performance
Model ZX1 0 2 05.2 .2ZX200 ZX 5.2
RMS Power in Watts, all channels driven
@ 14.4 Volts, 4Ω ≤stereo, 1% THD+N 60 x 2 70 x 2 85 x 2
@ 2Ω ≤stereo, 1% THD+N 75 x 2 100 x 2 125 x 2
@ 4Ω ≤mono, 1% THD+N 150 200 250
Length: 10 1/4” (260mm) 10 1/4” (260mm) 13 1/2” (342mm)
Specifications common to all models:
Height: 2 1/8” (54mm)
Width: 9 5/8” (244mm)
Frequency Response, ± 0.5 dB: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95 dB, a-weighted, re: rated power
Input Sensitivity: 125 mV - 5 V low level, 250 mV - 10 V high level
Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12dB per octave
Bass Boost: Variable 0 to +18 dB boost @ 40 Hz
ZX.2AMPLIFIER
L-
L+
4 5
Model .2ZX1 05
60 hms THD CEA-2006 x 2 @ 4 o , 1 V c4.4 d , 1% , (Watts)
Signal ise Rati -102 to No o
CEA-2006 A-weighte (ref 1W: , d)
Model .2ZX200
7 d 0 x 2 @ 4 ohms, 14.4V c, 1% , THD CEA-2006 (Watts)
Signal ise Rati to No o -98
CEA-2006 A-weighte (ref 1W: , d)
Model .2ZX2 05
85 x @ 4 o2 hms, 1 V4.4 d c, 1% , THD CEA-2006 (Watts)
Signal ise Rati to No o -98
CEA-2006 A-weighte (ref 1W: , d)
Figure 5
P FER ORMANCE
OPERAT OI N
Cross ver ntro oCol
5 d /0 - 200Hz, 12 B Oct
Inp ain ntrut G oCol
L w mV - V 2 - Vo Level 12: 5 5 , High Level: 50mV 10
Bass st ntr Boo oCol
0 t B b o +18d oost 0H @ 4 z
Especificaciones del producto
| Marca: | Kicker |
| Categoría: | Radio del coche |
| Modelo: | ZX150.2 |
¿Necesitas ayuda?
Si necesitas ayuda con Kicker ZX150.2 haz una pregunta a continuación y otros usuarios te responderán
Radio del coche Kicker Manuales
4 Octubre 2024
1 Octubre 2024
29 Septiembre 2024
23 Septiembre 2024
18 Septiembre 2024
16 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
6 Septiembre 2024
5 Septiembre 2024
Radio del coche Manuales
- Radio del coche Sony
- Radio del coche LG
- Radio del coche AEG
- Radio del coche Philips
- Radio del coche Panasonic
- Radio del coche Daewoo
- Radio del coche Ford
- Radio del coche Grundig
- Radio del coche JVC
- Radio del coche JBL
- Radio del coche Kenwood
- Radio del coche Medion
- Radio del coche Opel
- Radio del coche Pioneer
- Radio del coche Volvo
- Radio del coche Aiwa
- Radio del coche Akai
- Radio del coche Alpine
- Radio del coche Audison
- Radio del coche Telefunken
- Radio del coche Silvercrest
- Radio del coche Nedis
- Radio del coche Lenco
- Radio del coche Pyle
- Radio del coche Manta
- Radio del coche Tevion
- Radio del coche Caliber
- Radio del coche Hyundai
- Radio del coche Renkforce
- Radio del coche Clatronic
- Radio del coche Blaupunkt
- Radio del coche Harman Kardon
- Radio del coche Telestar
- Radio del coche Crunch
- Radio del coche Skoda
- Radio del coche Denver
- Radio del coche Stinger
- Radio del coche Hifonics
- Radio del coche Parrot
- Radio del coche Brigmton
- Radio del coche Maginon
- Radio del coche Xomax
- Radio del coche Varta
- Radio del coche Rockford Fosgate
- Radio del coche Marquant
- Radio del coche Krüger And Matz
- Radio del coche Clarion
- Radio del coche Muse
- Radio del coche Mac Audio
- Radio del coche Vieta
- Radio del coche Audiovox
- Radio del coche Dual
- Radio del coche Boss
- Radio del coche MB Quart
- Radio del coche Focal
- Radio del coche Auna
- Radio del coche Xblitz
- Radio del coche Tokai
- Radio del coche Naxa
- Radio del coche Nextbase
- Radio del coche Boston Acoustics
- Radio del coche Trevi
- Radio del coche Orion
- Radio del coche Magnat
- Radio del coche Technaxx
- Radio del coche Mercedes-Benz
- Radio del coche Autovision
- Radio del coche Lanzar
- Radio del coche Hertz
- Radio del coche Jensen
- Radio del coche Roadstar
- Radio del coche Scott
- Radio del coche Zenec
- Radio del coche MT Logic
- Radio del coche Kunft
- Radio del coche Shuttle
- Radio del coche Ultimate
- Radio del coche Conceptronic
- Radio del coche Fusion
- Radio del coche Norauto
- Radio del coche Revo
- Radio del coche Elta
- Radio del coche Axton
- Radio del coche VDO
- Radio del coche Soundstream
- Radio del coche DLS
- Radio del coche VDO Dayton
- Radio del coche Macrom
- Radio del coche Becker
- Radio del coche Watssound
- Radio del coche Tamashi
- Radio del coche Orava
- Radio del coche Emphaser
- Radio del coche Scion
- Radio del coche Phonocar
- Radio del coche US Blaster
- Radio del coche Eltax
- Radio del coche RTO
- Radio del coche Sevic
- Radio del coche Cartronix
- Radio del coche Dension
- Radio del coche Spectron
- Radio del coche Mtx Audio
- Radio del coche Ground Zero
- Radio del coche Multilaser
- Radio del coche Raveland
- Radio del coche ESX
- Radio del coche RetroSound
- Radio del coche Lark
- Radio del coche Planet Audio
- Radio del coche VW
- Radio del coche Rodek
- Radio del coche Toxic
- Radio del coche Eclipse
- Radio del coche Voxx
- Radio del coche SoundMAX
- Radio del coche Impulse
- Radio del coche Twister
- Radio del coche Majestic
- Radio del coche Mystery
Últimos Radio del coche Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
23 Octubre 2024
20 Octubre 2024
20 Octubre 2024
20 Octubre 2024
20 Octubre 2024
20 Octubre 2024