Konig DL-QUAKE250 Manual de Usario
Konig
Maquina de efectos
DL-QUAKE250
Lee a continuación 📖 el manual en español para Konig DL-QUAKE250 (77 páginas) en la categoría Maquina de efectos. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/77
DL-QUAKE250
MANUAL (p. 2)
Light xture Quake 250W
MODE D’EMPLOI (p. 14)
Jeu de lumières Quake 250 W
MANUALE (p. 26)
Luminaria Quake 250W
BRUKSANVISNING (s. 51)
Belysningsarmatur Quake 250W
MANUAL DE UTILIZARE (p. 63)
Corp de iluminat Quake 250W
HASZNÁLATI ÚTMUTATÓ (o. 39.)
250 W-os Quake vetítő
KÄYTTÖOHJE (s. 45)
Quake 250W valolaite
GEBRUIKSAANWIJZING (p. 20)
Verlichtingsarmatuur Quake 250W
ANLEITUNG (s. 7)
Lichteffekt Quake 250W
MANUAL DE USO (p. 33)
Dispositivo luminoso Quake 250W
NÁVOD K POUŽITÍ (s. 57)
Světelná konstrukce Quake 250W
ΕΓΧΕΙΡΙΔΙΟ XPHΣHΣ (σελ. 70)
Συσκευή Φωτισμού Quake 250W
DL-QUAKE250_A5.indd 1 2009.9.1 9:33:30 AM
2
ENGLISH
INTRODUCTION:
This advanced DMX controllable multi-color light effect has 12 different rotating gobo patterns and a
special feature called gobo shaking. The 250W halogen lamp ensures a room lling effect. This light
effect is ideal for permanent installation or mobile use
IMPORTANT INFORMATION BEFORE USE:
The QUAKE250 is not for household use. It is not a toy: it presents risks of serious injury due to
electric shock, high heat, and intense light. For safe operation, read this manual before using the
xture and observe all warnings and precautions printed here and on the xture. If you have questions
about how to operate the xture safely, please contact your König distributor or dealer.
Precautions:
• For protection against dangerous electric shock, the xture must be grounded (earthed). The AC
mains supply shall be tted with a fuse or circuit breaker and ground-fault protection.
• The xture operating voltage is printed on the rating label. Verify that the operating voltage closely
matches the AC supply voltage before connecting the xture. Do not connect the xture if the
voltage on the label differs from the AC mains voltage by more than ve percent.
• Verify that all used power cables are undamaged and rated for the current requirements of all
connected devices before use.
• There are no user serviceable parts inside except the lamp. Refer all service to a qualied
technician.
• Replace the lamp if it becomes defective or worn out. Allow the xture to cool for 15 minutes before
installing a new lamp and make sure the xture is disconnected from the AC mains supply.
• Keep all combustible materials (for example fabric, wood, paper) at least 50cm (20 inches) away
from the xture. Keep ammable materials well away from the xture.
• Provide a minimum clearance of 10cm (4 inches) around the fan and air vents.
• When suspending the xture above ground level, verify that the structure can hold at least 10 times
the weight of all installed devices and secure the xture with an approved safety cable. Block
access below the work area whenever installing or removing the xture.
• When carrying the xture, lock the mounting bracket securely and do not touch the lens or mirrors.
• Do not expose the xture to rain or moisture.
• Do not illuminate surfaces within 1 meter (39 inches) of the xture.
• Do not operate the xture if the ambient temperature exceeds 40°C (104°F).
• Never place lters or other objects over the lens or mirrors.
Important! Electric dimmers may damage the electronic components.
Although the QUAKE250 cannot be dimmed, it may be switched on and off remotely using switch
packs or the full-on and full-off levels on dimmer packs.
INSTALLATION:
The best way to hang the QUAKE250 is to use a rigging clamp. Bolt the clamp securely to the
mounting bracket. Verify that the structure can hold at least 10 times the weight of all installed devices
and secure the xture with an approved safety cable. Change to the desired angle by adjusting the
mounting bracket and tighten both swivel locks.
Install the xture at least 50cm (20 inches) away from combustible materials. Keep ammable
materials well away from the xture. Make sure the xture does not illuminate surfaces within 1 meter
(39 inches).
To ensure maximum lamp life, provide a minimum clearance of 10cm (4 inches) around the fan and air
vents. Make sure the ambient temperature will not exceed 40°C (104°F) and do not place the xture
on or nearby a loudspeaker.
DL-QUAKE250_A5.indd 2 2009.9.1 9:33:30 AM
3
OPERATION:
Read “IMPORTANT INFORMATION BEFORE USE” rst and verify all precautions are fullled before
operating.
Make sure the correct lamp is installed, read “SERVICE” how to (re)place the lamp.
Although the QUAKE250 cannot be dimmed, it may be switched on and off remotely using switch
packs or the full-on and full-off levels on dimmer packs. Disconnect the xture from AC power when
not in use.
The QUAKE250 has an advanced control panel. To set the desired function please read the following
instructions carefully.
Power
Menu
DMX
Up Down
Enter
Sound
Control panel
DMX address setting:
1. Press Menu button to access address code setting menu
Axxxx
2. Press UP or DOWN button to set the
DMX address code.
3. Press ENTER button to save the update
DMX address code.
Address code setting range
A001-A512
Test program:
Press Menu button to access the test program, select the menu
TEST and press
ENTER button to
save the setting, the LCD display ashes.
Press Menu button to exit this scene.
Mode setting:
Press Menu button to acces the menu Mode and press ENTER button to save the setting.
Press UP or DOWN button to select the mode of
Auto or Sond or dMH.
Press ENTER button to save the setting.
Press Menu button to upgrade the menu.
Auto Automatic mode
Sond Sound activity mode (w/o sound triggering will be black out)
dMH DMX mode
Sound Activity Sensitivity Setting:
Press Menu button to access the menu
SEnS
Press UP or DOWN to select the sound sensitivity (range: 0-99)
Press ENTER to save the setting.
Note: If the unit is in Master/Slave or Sound mode without any (music) triggering for 60 seconds, then
the unit will switch to black out mode.
DL-QUAKE250_A5.indd 3 2009.9.1 9:33:30 AM
Especificaciones del producto
| Marca: | Konig |
| Categoría: | Maquina de efectos |
| Modelo: | DL-QUAKE250 |
¿Necesitas ayuda?
Si necesitas ayuda con Konig DL-QUAKE250 haz una pregunta a continuación y otros usuarios te responderán
Maquina de efectos Konig Manuales
25 Agosto 2024
Maquina de efectos Manuales
- Maquina de efectos Manta
- Maquina de efectos BeamZ
- Maquina de efectos Velleman
- Maquina de efectos American DJ
- Maquina de efectos Steren
- Maquina de efectos Adj
- Maquina de efectos Behringer
- Maquina de efectos NGS
- Maquina de efectos Valcom
- Maquina de efectos Midas
- Maquina de efectos Elation
- Maquina de efectos QTX
- Maquina de efectos Valueline
- Maquina de efectos Fredenstein
- Maquina de efectos Chauvet
- Maquina de efectos Showtec
- Maquina de efectos Eurolite
- Maquina de efectos Monoprice
- Maquina de efectos Elysia
- Maquina de efectos HQ Power
- Maquina de efectos Antari
- Maquina de efectos Stairville
- Maquina de efectos Black Lion Audio
- Maquina de efectos Laserworld
- Maquina de efectos Martin
- Maquina de efectos Drawmer
- Maquina de efectos ColorKey
- Maquina de efectos JB Systems
- Maquina de efectos Evo-Lite
- Maquina de efectos Blizzard
- Maquina de efectos Hazebase
- Maquina de efectos Cameo
- Maquina de efectos Sagitter
- Maquina de efectos DJPower
- Maquina de efectos Doepfer
- Maquina de efectos Fun Generation
- Maquina de efectos Karma
- Maquina de efectos Lotronic
- Maquina de efectos IMG Stage Line
- Maquina de efectos Lexicon
- Maquina de efectos Futurelight
- Maquina de efectos The Confetti Maker
- Maquina de efectos Eliminator Lighting
- Maquina de efectos BoomTone DJ
- Maquina de efectos Klark Teknik
- Maquina de efectos Lab Gruppen
- Maquina de efectos TCM FX
- Maquina de efectos Magmatic
- Maquina de efectos Technical Pro
- Maquina de efectos Rosco
- Maquina de efectos Showven
Últimos Maquina de efectos Manuales
18 Octubre 2024
10 Octubre 2024
8 Octubre 2024
6 Octubre 2024
3 Octubre 2024
2 Octubre 2024
2 Octubre 2024
1 Octubre 2024
30 Septiembre 2024
29 Septiembre 2024