Kopykake Airmaster C3000R Manual de Usario

Kopykake No categorizado Airmaster C3000R

Lee a continuación 📖 el manual en español para Kopykake Airmaster C3000R (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

READ ME FIRST!

Studying this Owner’s Manual will make you

familiar with your airbrush so you can maintain

it with confidence. Also, should you need any

parts, you can identify and order them easily.

Kopykake 3699 West 240th St. Torrance California 90505 USA

Tel: 310-373-8906 Fax: 310-375-5275

sales@kopykake.com www.kopykake.com

Large Airbrush (1/3oz)

AB025 & ACD25

Small Airbrush (1/16oz)

AB018 & ACD18

Double Action Air Valve

AB070

Airbrush Models

AB018 AB025

ACD18 ACD25

Single Action - air flows through the

airbrush whenever compressor is ON

Double Action - Air flows through the airbrush

only when airbrush lever is depressed

MAINTENANCE: CLEANING

The Basic Cleaning

What I've found to be very helpful is to keep a cup of hot water and

add a few drops of airbrush cleaner, run this mixture through the

airbrush, while working lever action the whole time. Repeat this

between each color and each fill of the cup. A complete disassembly is

normally not needed. If your buildup isn't too bad, you should be able

to clean your airbrush without taking it apart. If old color has built-up in

the airbrush, you should let the entire airbrush soak in the airbrush

cleaner solution at full strength for about 30 minutes. Then loosen the

chucking nut (AB008), pull needle (AB009) back about 1 inch, and run

full strength cleaner through it after it has soaked. Rinse the airbrush

and dry.

No color is coming out of my airbrush, and I also notice

bubbles in my color cup.

Check Fluid nozzle (AB003), and/or nozzle cap (AB002).

When any of these are clogged you will get back feed into color cup.

Getting tiny lines of color without pressing main lever.

Your needle is not seating all the way into the airbrush.

Loosen the chucking nut of the needle and see if it will go in further. If it

doesn't the tip may be dirty and needs cleaning. By simply removing

your needle and gently cleaning it by removing all color and possibly

dried color near needle tip should fix problem because the needle was

not totally seated.

My air cap leaks air.

After removing the needle, remove the air cap. Take a very

small amount of bees wax, apply this to the threads. It will seal the

threads from air leaking this can be done on any air leaks you may

have.

My airbrush is over spraying or spitting

Check the point of your needle to make sure there is no

damage such as a bend or hook, remove the air cap and clean the

inside using a Q-tip, replace your needle if bent, or nozzle if damaged,

if you still see any spits.

***DO NOT***

disassemble airbrush for Basic Cleaning!

Problem:

Solution:

Problem:

Solution:

Problem:

Solution:

Problem:

Solution:

DISASSEMBLING YOUR AIRBRUSH

ASSEMBLING YOUR AIRBRUSH

Become familiar with your airbrush by studying the above

diagram. Remove each part by turning or pulling counter clockwise:

STEP 1: Disconnect the Airhose (AB014 or AB065) from the Airhose Connector

(AB0I3)

STEP 2: Remove Handle (AB007) by turning counter clockwise

STEP 3: Loosen Needle Chucking Nut (AB008)

STEP 4: Pull Needle (AB009) out, be careful not to damage the point

STEP 5: Unscrew the Spring Guide (AB011)

STEP 6: Remove the Needle Spring (AB012) and Needle Chucking Guide (AB010)

STEP 7: Remove the Main Lever (AB005) by pulling then twisting. Remove

Auxiliary lever (AB006) by pulling and twisting.

STEP 8: Remove the Crown Needle Cap (AB00I) and Nozzle Cap (AB002)

STEP 9: Using the small flat wrench provided with your airbrush, remove the

Nozzle (AB003) by placing the wrench over the two flat spots and turning

counter clockwise.

STEP 1: Using the nozzle wrench, screw in and tighten the Nozzle

STEP 2: Screw on the Nozzle Cap and hand tighten

STEP 3: Screw on the Crown Cap and hand tighten

STEP 4: Hold the airbrush as shown in Diagrams B & C. Take the Auxiliary Lever

(Diag. C) and insert inside the opening, twisting it so that the hump is

towards the back. Let it rest against the back of the opening.

STEP 5: Stop. Study the Main Lever. Notice there is a thinner, rounded section on

the flat part

under the round head. This side goes towards the back of the opening.

Refer to Diagram B. Insert the Main Lever into the opening and guide the

two pins into the two channels located on the walls inside the opening.

Move head back against the Auxiliary Lever and hold there. Hold these

parts secure then go to Step 6.

STEP 6: Insert the Needle Chucking Guide, channel down into the back of the

airbrush. Slide the Needle Spring over the Needle Chucking Guide. Insert

the Spring Guide over the Needle Spring and screw in until tight. This

spring mechanism will push the main lever and Auxiliary Lever forward.

STEP 7: Insert the Needle through the Needle Chucking Guide and slowly push all

the way forward. Screw on the Needle Chucking Nut until tight.

STEP 8: Cover the back of the airbrush with the Handle.

"" Caution: Do not apply excessive force when tightening"'

ACCESSORIES (Not pictured)

AB015 4oz. Poly Bottle with dispenser cap

AB016 Nozzle Wrench

AB050 Moisture Trap (Barbed) - for Airmaster & KromaJet compressors

AB051 Moisture Filter with hose fitting - for Airmaster Plus compressor 91000 Airbrush Cleaner

Rev. 8-13-2010

Diagram B Diagram C

Especificaciones del producto

Marca:	Kopykake
Categoría:	No categorizado
Modelo:	Airmaster C3000R
Color del producto:	Black, Red
Peso.:	261 g
Longitud del cable:	1.8 m
Bluetooth:	Nee
Tipo de embalaje:	Doos
Tecnología de conectividad:	Bedraad
Control del volumen:	Draaiknop
Número:	1
Método de uso:	Hoofdband
Uso recomendado:	Gamen
Tipo de auricular:	Stereofonisch
Impedancia:	32 Ohm
Colocar los auriculares de los altavoces.:	Circumaural
Rango de frecuencia de los auriculares:	20 - 20000 Hz
Conector de 3,5 mm:	Nee
tipo microfoon:	Boom
conexión USB:	Nee
Color de cables:	Zwart
Diámetro del altavoz:	40 mm
Tipo de unidad de control:	Lijnbesturingseenheid
Sensibilidad del micrófono:	-56 dB
Género recomendado:	Jongen/meisje
2x conectores de 3,5 mm:	Ja
Tipo-producto:	Headset