Kress KUB60.91 Manual de Usario

Kress maquina de atornillar KUB60.91

Lee a continuación 📖 el manual en español para Kress KUB60.91 (3 páginas) en la categoría maquina de atornillar. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

060817- 1 DR www.elitescreens.com

Manual Pull- Down Projection Screen

Elite Manual Series

USER’S GUIDE

Pre-installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

INSTALLATION

Flush Wall Mounting

1. Measure the distance between the keyholes located on the back of the end cap

2. stalled for the pre- Mark the location of where the screen is to be in drilled hole.

3. the area and drilling the hole, insert the proper After marking screw into the drilled hole and leave

about 1/8” of an inch from the wall to mount the screen.

4. Mount your screen from the keyhole located on back of screen’s left and right end cap.

Back of end cap

Front view

Side view

060817- 2 DR www.elitescreens.com

Flush Ceiling Mounting

1. Measure the distance between the top screw holes located on

the top of the end caps.

2. Mark the location of where the screen is to be installed

for the pre-drilled hole.

3. Drill your hole, use a hollow wall anchor if needed

4. Insert the proper screw into the drilled hole and the secure

screen to the ceiling.

Ceiling Suspended Mounting (additional hardware required)

Optional installation using a chain to hang the screen from the ceiling.

1. You can also hang the screen on a ceiling by using a chain and hang it by the two loops (models 71-120)

located on ea (models 135-170).ch end of the case or by the end cap’s ears

SCREEN OPERATION

Note: Always pull the screen down or let it up in a 90-degree vertical angle. Do not allow the screen to touch

the screen case when the screen goes up or comes down to avoid damaging the screen material.

Note: Chain and U bolt/D ring not included.

060817- 3 DR www.elitescreens.com

1. Pull the screen down from the lanyard or from the handle only in a 90-degree angle. Do not attempt to pull

the screen down by the surface or touch the screen, as it will damage the screen and void the warranty.

Note: An internal auto- en to stop and lock on the position at lock mechanism system will cause the scre

intervals.

2. If you want to the screen to retract back, simply pull the screen down more than 2 inches and retract the

screen back by quickly and smoothly releasing it up gently.

Note: Always release at a 90-degree angle and do not let go until the screen is entirely inside the case

If ever the screen feels stuck, keep in mind that the screen’s mechanism is new and needs to be run

up/down a few times to loosen up. If this happens, carefully with a little force yank the screen straight

down to unlock the screen.

Note: Improperly bringing the screen up/down will damage the screen material or rolling system.

RETRACTION TIP: If you are not able to pull the screen down two inches when attempting to retract it, give

the screen a quick yank downwards with a little bit of force. Please be sure to not stand directly under the

housing of the unit when yanking down on the screen.

MAINTENANCE

Clean matte white screen material with a soft cloth and mild soap with water.

When not in use, retract screen in its housing to keep the screen material surface clean.

N : OTE

Regardless of mounting method, the screen should be securely supported so that vibration or even abusive

pulling on the viewing surface will not cause the case to work loose or fall. The installer must insure that the

fasteners used are of adequate strength and suitable for the mounting surface chosen.

Especificaciones del producto

Marca:	Kress
Categoría:	maquina de atornillar
Modelo:	KUB60.91
Color del producto:	Wit
Peso.:	7393 g
Nivel de ruido:	- dB
Fuente-de-alimentación:	AC
Colocación:	Desktop
Relación de aspecto original:	16:10
Estándares wifi:	802.11a, 802.11b, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
red LAN:	Ja
Distancia focal fija:	4.21 mm
Relación de contraste típica:	500000:1
Capacidad de zoom:	Ja
Posicionamiento en el mercado:	Draagbaar
Brillo del proyector:	3300 ANSI lumens
Tecnología de proyección:	3LCD
Resolución nativa del proyector:	WXGA (1280x800)
Adecuado para tamaños de pantalla:	60 - 130 "
Objetivo de distancia de proyección:	- m
Puerto(s) VGA (D-Sub):	1
Número de puertos HDMI:	2
Tipo de conexión en serie:	RJ-45
Audio-ingan (L, R):	1
Entrada de vídeo compuesto:	1
Vídeo de componentes (YPbPr/YCbCr):	2
Puerto DVI:	Nee
Número de puertos Ethernet LAN (RJ-45):	1
Enfocar:	Auto
Rango focal:	- mm
Vida útil de la fuente de luz.:	20000 uur
Tipo de fuente de luz:	Laser
Consumo de energía (en espera):	- W
Consumo de energía (máx.):	290 W
Relaciones de aspecto admitidas:	4:3, 14:9, 16:9
Formato de señal analógica:	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Full HD:	Ja
Salida de audio (izquierdo, derecho):	1
LAN Ethernet, velocidades de transferencia de datos:	10, 100 Mbit/s
Número de puertos USB 3.2 Gen 1 (3.1 Gen 1) Tipo A:	2
Número de puertos USB 2.0 Tipo-B:	1
Wifi.:	Ja
voltaje-de-entrada-de-CA:	100 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Consumo de energía (típico):	280 W
Temperatura de funcionamiento (TT):	0 - 40 °C
Tipo-producto:	Projector met ultrakorte projectieafstand
Código del Sistema Armonizado (SA):	85286200