Laine STILTS Manual de Usario

Laine No categorizado STILTS

Lee a continuación 📖 el manual en español para Laine STILTS (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Thank you for purchasing this dual Equaliser
module from Laine. We hope it soon
becomes the go-to tone shaping tool in your
1U row.
Overview
Slts provides two channels of single control ltering, with lt
or high shelf topologies. It can be switched seamlessly
between these two styles of EQ.
Tilt: Boost low frequencies while also cung highs,
or boost high frequencies whilst also cung lows.
Baxandall High Shelf: A gentle high frequency gain shelf
allowing boosting or cung whilst leaving the mid-range and
bass frequencies untouched.
Use the lt and high shelf to perform a variety of mixing
and sound design dues ranging from subtle, non-resonant
brightness and clarity adjustments to low-end rumble
removal, boosted low pass ltering and sweep EQ.
Each channel’s fully analogue signal path comprises several
mul-band acve lters that are summed and mixed through
a VCA. These active lter networks are tuned to provide a
transparent response with controls at the centre posion,
whilst also allowing for smooth adjustment on low and high
frequency bands.
Operaon
In the default lt mode (Mode Switch in the raised posion)
turning a control knob clockwise simultaneously boosts treble
and cuts bass. Turning an-clockwise boosts bass and cuts
treble. These boosts and cuts pivot around the mid-range in
the 800Hz region. With the control knob at
12 o’clock the frequency response is neutral.
With Baxandall high-shelf mode enabled, turning the control
knob clockwise past 12 o’clock introduces a gentle high shelf
EQ weighted around the upper mid-range in the 1kHz region.
Turning the control knob an-clockwise results in a wide high
shelf cut with subtle bass and mid-range adjustments.
The signal paths of both channels are idencal, and
depending on how they are routed externally, the
channels can be congured as dual independent lters,
or as a stereo-in, stereo-out lter with each output panned
le and right. Patching the output of CH1 to CH2 runs the
lters in series and allows for pronounced sound shaping and
band pass responses.
Each channel provides up to +/- 8dB of low and high-
frequency gain control, summing into a low noise VCA
output stage. Hot input signals over 15VPP are
saturated
by acve Zener diode clipping at the input buer.
The boost and cut controls are CV responsive to input
signals of 0-8V. Turn the control knobs fully an-
clockwise to allow full CV control of the lter gain
range.
Front Panel
➊ ❷ CH 1, CH 2 Control
These potenometers control the frequency response
of the equaliser channel. Turn an-clockwise for full CV
control.
❸ Mode Switch
The latching switch is used to select EQ topologies for
both channels. Tilt (with the Mode Switch in the raised
posion) and Baxandall High Shelf (with the Mode
Switch latched down)
❹ ❺ CH 1, CH 2 Audio Level LEDs
The clear LED represents CH1 audio input signals, the
green LED displays CH 2.
❻ ❼ CH 1, CH 2 CV Input
These CV input jacks are responsive to signals ranging
from 0 to 8V and show an input impedance of 100k.
Turn the channel’s control knob fully an-clockwise for
full CV control through the jack inputs. With no jack
patched, CH 2 is normalled to the
CH 1 CV input.
❽ ➒ CH 1, CH 2 Audio Input
The AC-coupled input jacks will begin to clip
with input signals over 15VPP. They show an input
impedance of 100k. With no jack patched, CH 2 is
normalled to the CH 1 Audio input.
❿ ⓫ CH 1, CH 2 Audio Output
These output audio signals for CH1 and CH2. With the
control knob in the central posion the output signal
will match the signal level at the audio inputs.
STILTS
Dual VC Tilt/High Shelf Equaliser
Designed in the Intellijel 1U format
for Eurorack modular systems.
User Manual
20
/1
2
/23
Typical Response Graphs
Tilt EQ Response
Baxandall High Shelf Response
s
Signal Flow Diagram
Specicaons
• Intellijel 1U format
• Width 18HP
• Depth 32mm
• Power requirements ~60mA
+12V
~58mA -12V
• Control voltage range
0-8V
• Impedance:
Input 100K
Output 1K
Standards Compliance
This device complies with internaonal EMC and Safety
Standards when installed in a fully compliant rack. It has been
assembled and tested in the United Kingdom.
UKCA
UK Electrical Equipment (Safety) Regulaons 2016 (SI
2016/1101) UK Electromagnec Compability Regulaons
2016 (SI 2016/1091.) The Restricon of the use of certain
Hazardous Substances in Electrical and Electronic Equipment
Direcve (RoHS2) 2011/65/EU.
CE
EU Low Voltage direcve (LVD) 2014/35/EU,
EU Electromagnec Compability direcve (EMC) 2014/30/EU.
The Restricon of the use of certain Hazardous Substances in
Electrical and Electronic Equipment Direcve (RoHS2)
2011/65/EU.
FCC
This device complies with Part 15 of FCC rules. Operaon
is subject to the following two condions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received,
including interference that may cause undesired
operaon.
Electromagnec Compability
BS EN 55032:2015, Class B. BS EN 55035:2017.
Electrical Safety
BS EN 62368-1:2014 + A11:2017, EN 62368-1:2014 +
A11:2017, CSA CAN/CSA-C22.2 NO. 62368-1 2nd Ed, 2014.
Environmental Temperature
Operang: +1 to 30°C.
Storage: -20 to 50°C.
Warranty
Laine warrants this product to be free of defects in
materials or construcon for a period of one year
from the date of purchase (proof of purchase or
invoice is required.)
Defects resulng from incorrect power supply
voltages over or under 12V, abuse of the product,
removing knobs, changing face plates, or any other
causes determined by Laine to be the fault of the user
are not covered by this warranty, and normal service
charges will apply. During the warranty period, any
defecve products will be repaired or replaced, at the
discreon of Laine, on a return-to-Laine basis with
the customer paying the shipping cost to Laine.
Laine implies and accepts no responsibility for harm
to person or apparatus caused through the operaon
of this product.
Product Support Contact
Please contact jack@laine.uk with any quesons,
return requests and comments.
www.laine.uk
Instagram @laine.modular

Especificaciones del producto

Marca: Laine
Categoría: No categorizado
Modelo: STILTS

¿Necesitas ayuda?

Si necesitas ayuda con Laine STILTS haz una pregunta a continuación y otros usuarios te responderán


No categorizado Laine Manuales

Laine

Laine STILTS Manual de Usario

14 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024