Lanzar HTG559BT Manual de Usario

Lanzar receptor HTG559BT

Lee a continuación 📖 el manual en español para Lanzar HTG559BT (18 páginas) en la categoría receptor. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/18

www.Lanzar.com

INTRODUCTION

LANZAR ampliers provide high-performance sound reinforcement for your

mobile audio equipment. Its versatility enables compatibility with optional

Equalizers, Frequency Dividing Crossover Networks, and other audio processors

in a customized system. The Multi-Mode bridging capabilities allow exibility in

hosting several dierent speaker congurations.

To achieve optimum performance, it is highly recommended that you read this

Owners Manual before beginning installation.

WARNING

High powered audio systems in a vehicle are capable of generating "Live Concert”

high levels of sound pressure. Continued exposure to excessively high volume

sound levels may cause hearing loss or damage. Also, operation of a motor vehicle

while listening to audio equipment at high volume levels may impair your ability

to hear external sounds such as; horns,warning signals, or emergency vehicles,

thus contributing to a potential trac hazard. In the interest of safety, LANZAR

recommends listening at lower volume levels while driving.

TABLE OF CONTENTS

PLANNING YOUR SYSTEM

WIRING CONNECTION

PANEL LAYOUT

CONTROL FUNCTIONS

SPEAKER DIAGRAMS MONO CHANNEL

TROUBLESHOOTING GUIDE

WARNINGS

SPECIFICATION

www.Lanzar.com

PLANNING YOUR SYSTEM

Before beginning the installation, consider the following:

1. Do you plan to add additional mobile electronics equipment in the future?

If you plan to expand your system by adding other components sometime in

the future, ensure adequate space is left and cooling requirements are met.

2. Should you use high or low level inputs?

Your Amplier has been designed to accept Low-Level (Pre-Amp outputs from

your radio) source signal. If your radio/source is equipped with Pre-Amp outputs,

it is possible to utilize them to drive the Amplier and the 2 front speakers.

Then, use the built-in power of your radio to drive the 2 rear speakers.

3. Are your components matched?

The RMS power rating of your speaker(s) must be equal or greater than the

RMS power rating of your amplier. Your speaker(s) also must be 2- 8 Ohms

impedance for stable amplier operation. Impedance information is normally

printed on the speaker basket or magnet.

4. Where will the amplier be installed?

Consider both the length of your leads, and routing when determining the

mounting location. It is best to run power and RCA wiring on opposite sides of

the vehicle to prevent induced noise. Pre-amp input jacks require a length of

high quality shielded male to male RCA patch cord.

CONNECTINGTHE POWER

CAUTION

AS A PRECAUTION, DISCONNECTTHE POWER WIRE FROM THE BATTERY WHILE

MAKING THE POWER AND GROUND CONNECTIONS TO THE AMPLIFIER.

4/8 GAUGE (Thicker if planning for additional Ampliers) wire is recommended

for both the power and ground wires 12 Gauge, for the remote turn-on wire 16

Gauge. Both types are available at most Mobile Audio Dealers or Installation

Shop.

Especificaciones del producto

Marca:	Lanzar
Categoría:	receptor
Modelo:	HTG559BT
Color del producto:	Roestvrijstaal
Función de calentamiento:	Ja
Función de descongelación:	Ja
Material de la carcasa:	Roestvrijstaal
Activos:	1000 W
Número de rebanadas:	1 snede(n)
Botón detener/cancelar:	Ja
Mecanismo de pan autocentrante:	Ja
Bandeja recogemigas extraíble:	Ja
Configuración de color de corteza variable:	Ja
Almacenamiento de cable:	Ja
Luz indicadora:	Ja
Niveles de bronceado:	5
Número de cerraduras:	1
voltaje-de-entrada-de-CA:	230 V