Liberty Pumps CSP-257 Manual de Usario

Liberty Pumps Pompa CSP-257

Lee a continuación 📖 el manual en español para Liberty Pumps CSP-257 (14 páginas) en la categoría Pompa. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/14

IMPORTANT:

Prior to installation, record Model, Serial Number, and

Code Number from pump nameplate for future reference.

MODEL ________________________

SERIAL ______________________

CODE ______________________

INSTALLATION

DATE _____________________ __

CSP-237 1/3HP 115V 60Hz

CSP- 7 1/3HP 115V 60Hz 25

CSP-457 1/2HP 115V 60Hz

7000 Apple Tree Avenue

Bergen, NY 14416

Phone: (800) 543-2550

Fax: (585) 494-1839

www.libertypumps.com

Contents

1.) General Information and Safety

Guidelines

2.) Installation

3.) Maintenance and Troubleshooting

Installation Manual 4353 0C00

Model CSP-237, CSP-257, and CSP-457 Crawl Space Pump

Before installation, read the following instructions carefully. Each Liberty pump is individually factory tested to insure proper

performance. Closely following these instructions will eliminate potential operating problems, assuring years of trouble-free service.

 Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.

 The electrical connections and wiring for a pump installation should only be made by qualified personnel.

 This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be

certain that it is connected only to a properly grounded, grounding-type receptacle.

 Do not bypass grounding wires or remove ground prong from attachment plugs.

 Do not use an extension cord.

 This pump requires separate, properly fused and grounded branch circuit. Make sure the power source is properly sized for the a

voltage and amperage requirements of the pump, as noted on the nameplate.

 The electrical outlet shall be within the length limitations of the pump power cord, and at least 4 feet above floor level to minimize

possible hazards from flood conditions.

 The installation must be in accordance with the National Electric Code and Plumbing Codes as well as all applicable local codes

and ordinances.

Fig. 1 – Typical Residential Installation

This is a recommended installation only.

1. General Information and Safety Guidelines

2. Installation

Figure 1

Application: The CSP- , CSP-257, and CSP-457 crawl space pumps are designed for use a crawl space or where pooling water 237 in

is occurring. Allowing the water in the pump or discharge line to freeze may cause damage to the pump. In colder regions, the pump

should only be installed indoors or deep enough to be below the frost line.

A. For in ground installation a hole should excavated as small as possible, leaving at least 8” of diametrical clearance. BACKFILL:

Course gravel is recommended for backfill.

B. The CSP- , CSP-257, and CSP-457 include a perforated basin for gathering water. Additional inlets may be added with INLET: 237

a hole saw for allowing drain lines or weep tiles.

C. When attaching the discharge, place the pump in the basin being careful to keep float from any obstruction or from DISCHARGE:

hitting the tank wall. The CSP- , CSP-257, and CSP-457 include a DHK-24 discharge hose kit. A 1-1/2” X 1-1/4” hose adapter 237

will thread into the pump discharge. The 24’ flexible hose will fit over the barbed fitting of the adapter and should be tightened

down with a hose clamp. The hose will fit through the grommet in the basin cover and can be cut to the required length. Exit the

discharge of water in an area that will drain away from the building and foundation.

D. The CSP- , CSP- and CSP-457 include a threaded check valve for use with the discharge hose. If the CHECK VALVE: 237 257,

pump is short cycling, then a check valve may be required. This would prevent water from draining back through the discharge

hose into the basin. When using a check valve, the discharge line must be protected from freezing by running the discharge deep

enough below ground level to be beneath the frost line. See figure 1.

E. The pump power cord is equipped with a grounding conductor and grounding-type 3-prong plug. It should be POWER CORD:

connected to a separately fused, grounded, 3-wire grounding-type receptacle of 15-amp capacity with the proper . Make sure 115V

all electrical wiring and connections are in accordance with the National Electric Code and all applicable local codes.

 Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.

 DO NOT remove the plug or ground prong.

 DO NOT use an extension cord.

Especificaciones del producto

Marca:	Liberty Pumps
Categoría:	Pompa
Modelo:	CSP-257

¿Necesitas ayuda?

Si necesitas ayuda con Liberty Pumps CSP-257 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Pompa Liberty Pumps Manuales

Liberty Pumps 250 Manual de Usario

1 Octubre 2024

Liberty Pumps 457 Manual de Usario

1 Octubre 2024

Liberty Pumps 230 Manual de Usario

1 Octubre 2024

Liberty Pumps CSP-257 Manual de Usario

1 Octubre 2024

Pompa Manuales

Últimos Pompa Manuales

JANDY JCP07-3AT-S Manual de Usario

27 Octubre 2024

Gude INOX 100/24 Manual de Usario

26 Octubre 2024

Vivaria Vario N-3000 Manual de Usario

26 Octubre 2024

Maruyama MS655 Manual de Usario

26 Octubre 2024

Gardena RWT Pump 2000/2 Li-18 Manual de Usario

15 Octubre 2024

Ozito PTP-012A Manual de Usario

15 Octubre 2024

MSW -AN-100 Manual de Usario

15 Octubre 2024

MSW -MN34 Manual de Usario

15 Octubre 2024

MSW -MN34M Manual de Usario

15 Octubre 2024

MSW -AOP40S Manual de Usario

15 Octubre 2024