Lifespan SP1000 Manual de Usario

Lifespan Equipo de gimnasia SP1000

Lee a continuación 📖 el manual en español para Lifespan SP1000 (2 páginas) en la categoría Equipo de gimnasia. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Stretch Partner Warranty

The LifeSpan Stretch Partner comes with the following warranty:

Parts: 90 days seat and flex bumper

1 year for commercial use

2 years for residential use

Frame: 1 year for commercial use

5 years for residential use

PCE Health and Fitness Warrants that the equipment it manufactures is free from defects in material and workmanship under normal

use and service.

If within the timeframe specified above, any part of the Stretch Partner fails to operate properly, contact your authorized PCE Health and

Fitness Retailer to report the problem or contact PCE Health and Fitness at www.pcefitness.com or (435) 940-1180.

PCE Health and Fitness reserves the right to make changes and improvements to our products without incurring any obligations to similarly

alter any product purchased. In order in insure our product warranty and to ensure the safe and efficient operation of LifeSpan equipment,

only authorized parts can be used. The product warranty is void if any parts, other than those provided by PCE Health and Fitness are used.

Exclusions and Limitations

• This Warranty does not apply to any defects caused by negligence, misuse, or improper assembly or maintenance.

• This warranty does not apply to discoloration of paint or plastics.

• PCE Health and Fitness will not be responsible for incidental or consequential damages.

• This warranty is non-transferable from the original owner.

Registration

You must register your LifeSpan product before a warranty claim can be processed and proof of purchase must be demonstrated at the time a

claim is made. To complete your registration online, go to www.pcefitness.com and fill out the online registration or fill out the

warranty card provided with your Stretch Partner and mail it today.

CONTENTS:

• Base

• Handlebar post

• Seat Frame

• Handlebars & Safety Straps

• Seat Bottom

• Seat Back

• Pedal Axle

• Pedals

• Seat Pivot Axle

• Instruction Bracket with

User Instructions

• Plastic Covers

• Hardware Bag/Tools

a. 8 - 5mm Frame Screws

b. 8 - Bent Washers

c. 1 - 5mm Allen Wrench

d. 1 - 4mm Allen Wrench

e. 2 - 14mm Wrench’s

f. 1 - Phillips Screwdriver

g. 1 - 14mm Lock Nut

h. 1 - Straight Washer

STEP 1:

FRAME ASSEMBLY

a. Insert the handlebar post bracket into

the end of the base frame.

b. Align the holes and using four, 5mm

Allen head screws and 4 Bent Washers,

hand tighten all four screws before

securely tightening them with the Allen

wrench provided.

STEP 2:

PLASTIC COVERS

a. Remove the three Phillips head screws

already in place on the plastic covers.

b. Place the 2 plastic halves in place over

the front joint and tighten down the 3

Phillips head screws.

STEP 3:

HANDLEBAR ASSEMBLY

a. Put the Safety Strap around the

handlebars and push the handlebar

down onto the handlebar post.

b. Locate the Instruction bracket and align

the screw hole in the bracket with the

screw hole in the front of the handlebar

post. Hand tighten a 5mm Allen head

screw with Bent Washer.

c. Hand tighten the remaining 3 screws

with bent washers and then securely

tighten all four screws with the 5 mm

Allen wrench provided.

STEP 4:

SEAT AXLE A

a. Locate the seat fra

seat frame in plac

the frame with the

b. Once the holes are

SURE THAT THE IN

THE BRACKET AS

c. Using the 4mm All

shown in the pictur

STEP 5:

SEAT ASSEMBLY

a. Locate the seat bottom, remove the four screws from the back of the seat

bottom and securely tighten all four screws on the seat frame as shown in

diagram below.

b. Locate the seat back, remove the four screws from the seat back and

securely tighten all four screws onto the seat frame bracket.

Note: Turn the seat bottom so that the front of the seat is flush with the oval seat tube. It

should not overhang past the seat tube.

STEP 6:

PEDAL AXLE/PEDALS

a. Locate the pedal axle and the foot pedal. One of the ends on the axle already has a nut and washer in

Over the opposite end, slide the left side pedal.

b. Push the axle through the pedal axle shaft and push the right pedal over the end.

c. Secure the pedal in place by using a washer and locknut. To tighten the nut you will need to use the 2 -

wrenches provided. Put one wrench on each end of the axle and turn clockwise until tight.

d. After the axle nuts are tightened, push the axle caps into the pedals.

Push base onto bracket. Securely

tighten four 5mm Allen head

screws with bent washers.

Push the axle into the brack

and make sure the indent in

axle is aligned with the hole

the frame bracket.

Turn the seat

bottom so the

front of the seat

is flush with the

seat tube.

Tighten down three

Phillips head screws.

Put the right pedal on the axle

and insert through shaft.

Use a socket wrench on each

end to tighten the axle nuts. Push on pedal cap

Below handlebar

Over handlebar

Especificaciones del producto

Marca:	Lifespan
Categoría:	Equipo de gimnasia
Modelo:	SP1000
Color del producto:	Wit
Peso.:	820 g
Ancho:	164.8 mm
Altura:	53.4 mm
Peso del embalaje:	830 g
Ancho del embalaje:	55 mm
Empaquetadura en profundidad:	165.3 mm
Altura del embalaje:	140 mm
Amable:	Aansluitdoos
Material de la carcasa:	Aluminium
Tipo de embalaje:	Doos
Soporte de colocación:	Binnen
Diámetro:	137 mm
País de origen:	China
Capacidad máxima de peso:	- kg
Compatibilidad de marca:	LevelOne
Compatibilidad:	FCS-5059\nFCS-5060\nFCS-5068\nFCS-5092\nFCS-5093
Altura del paquete principal (exterior):	370 mm
Ancho del embalaje principal (exterior):	450 mm
Peso bruto del embalaje principal (exterior):	24600 g
Longitud del paquete principal (exterior):	365 mm
Cantidad por caja principal (exterior):	30 stuk(s)
Código del Sistema Armonizado (SA):	85299020