Lindy 38063 Manual de Usario
Lindy
extensor AV
38063
Lee a continuación 📖 el manual en español para Lindy 38063 (8 páginas) en la categoría extensor AV. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
© LINDY ELECTRONICS LIMITE
Fibre
O
User Manual
Benutzerhandbuch
Manuel Utilisateur
Manuale d’uso
LINDY Exten
LINDY
Extend
w
Tested to comply with FCC Sta
For Home and Office Use
ED &
LINDY-ELEKTRONIK GMBH -
THIRD EDITION
Optic
HDMI Ex
h
r
No.38003
nder 300m Multimode No. 3
der 700m
Single Mode
No.
www.lindy.com
andards
(NOVEMBER 2011)
xtender
English
Deutsch
Français
Italiano
3
38003
.
38063
IMPORTANT HEALTH AND SAFETY INFORMATION
WARNING! RISK OF INJURY!
This product contains visible and/or invisible laser beams which could be harmful to eyes and
skin. Avoid eye and skin exposure.
If no fibre cable is connected or if this cable is broken the lasers are automatically switched off.
If you experience any problems with this product please contact LINDY. Under no
circumstances must the product housing be opened.
SICHERHEITSHINWEIS
ACHTUNG! VERLETZUNGSGEFAHR!
Innerhalb dieses Produktes wird sichtbare oder unsichtbare Laserstrahlung erzeugt, die Augen
und Haut nachhaltig schädigen kann. Nicht dem Strahl aussetzen oder direkt in den Strahl
schauen!
Bei nicht angeschlossenem oder gebrochenem LWL-Kabel werden die Laser automatisch
abgeschaltet. Bei Störungen oder Problemen setzen Sie sich bitte mit LINDY in Verbindung.
Das Gehäuse des Produktes darf unter keinen Umständen geöffnet werden.
INFORMATION IMPORTANTE: SANTE ET SECURITE
ATTENTION! RISQUE DE BLESSURES!
Ce produit contient un faisceau laser visible et/ou invisible qui peut endommager les yeux et la
peau. Evitez l'exposition aux yeux et à la peau.
Si aucune fibre optique n’est connectée ou si la fibre est cassée, les lasers seront
automatiquement éteints.
Si vous rencontrez des problèmes avec ce produit, merci de contacter LINDY. Le produit ne doit
être en aucun cas ouvert.
IFORMAZIONI IMPORTANTI SICUREZZA E SALUTE
ATTENZIONE! RISCHIO DI LESIONI!
Evitare l'esposizione diretta a occhi e alla pelle, questo prodotto contiene raggi laser visibili e/o
invisibili che potrebbero risultare dannosi agli occhi e alla pelle.
Se non è connesso nessun cavo o se il cavo collegato è danneggiato, il laser si spegne
automaticamente.
In caso di problemi con questo prodotto contattare la LINDY. Questo prodotto non deve essere
aperto in nessun caso.
No. 38063
(
7
00m):
MAX OUTPUT 1mW≤
Multi Wavelength: 1310/1430/1550nm
CLASS 1 LASER PRODUCT
No. 38003 (300m):
MAX OUTPUT 1mW≤
Multi Wavelength: 850/1310/1550nm
CLASS 1 LASER PRODUCT
User Manual English
1
Introduction
Thank you for purchasing the LINDY Fibre Optic HDMI Extender! The Fibre Optic HDMI
Extender allows you to extend Full HD 1080p and even higher resolution signals up to 4K2K
including all HDMI 3D formats up to:
• 300m (No.38003) using multimode (50/125µm) SC Duplex fibre cable
• 700m (No.38063) using single mode (9/125µm) LC Duplex fibre cable
• 3000m (No.38063) using single mode (9/125µm) LC Duplex fibre cable W/O HDCP
Package Contents
LINDY Fibre Optic HDMI Extender p2-x2 (1 x Transmitter, 1 x Receiver)
Multi-Country Power Adapter (5V DC) x 2
This User Manual
Features
Extends HDMI or DVI signals up to 300m, 700m or 3000m depending on model and HDCP
Suitable for use with Home Theater, professional graphics and computer equipment
Uses standard, inexpensive SC or LC Duplex Fibre Cable, depending on model
Auto power save mode when source device is powered off
Auto Laser disable if fibre cable is broken or removed
Optional IR Repeater option (sold seperately, LINDY No. 38006)
Specification
Over 10Gbps Total Bandwidth over Single 2-core Fiber Optic Cable Link
Compatible with HDMI 1.3b specification and all 3D functions acording to HDMI 1.4a
Supports all current HDMI resolutions and all current audio formats
Deep Colour capable: supports 30/36/48 bit colour depth
Maximum fibre cable length 300m (No.38003) or 700m (No.38063) or 3000m if HDCP is not
required (No.38063)
Maximum HDMI cable length up to 5m in and out
Supports HDCP
Supports DVI 1.0
Dimensions: 11cm x 7.5cm x 3cm (LxWxH, each unit)
User Manual English
2
Overview
The overview shown below is for the 300m Extender 38003. The 700m Extender uses a similar
housing with LC Duplex connectors.
Fibre Optic HDMI Transmitter
Fibre Optic HDMI Receiver
* The fixing post for connector lock is designed to be used with the LINDY Connector Lock,
available for our range of Premium Gold HDMI cables, and for our range of HDMI cables with
integrated lock, to provide a more secure connection between your HDMI cable and the
extender.
Rear
Front
Link Indicator
Power Indicator
IR Indicator
Power supply
Connector
* Fixing post for
Connector Lock
HDMI Type A
Connector
IR Repeater
Connector
Duplex SC Fibre
Cable Connector
Rear
Front
Power supply
Connector
* Fixing post for
Connector Lock
HDMI Type A
Connector
IR Eye
Connector
Link Indicator
Power Indicator
IR Indicator
Duplex SC Fibre
Cable Connector
User Manual English
3
Installation
Important! Before starting the installation, please ensure that all devices are powered off.
The following steps are for an installation using HDMI equipment, if you are using DVI
equipment you should substitute the HDMI cables for DVI to HDMI cables where required.
1. Connect your HDMI source to the Fibre Optic Transmitter device using a HDMI cable
(maximum length 5m).
2. Remove the dust covers from the Fibre Optic Transmitter and Receiver ports and your Fibre
Cable.
3. Connect one end of the duplex fibre cable to the optical port on the Transmitter and the
other end to the optical port of the Receiver. This must be set up as 1:1 connection and NOT
as a cross over connection as provided by some Duplex Cables with pre-installed clamp on
the Duplex connector. If you have such a cross over cable please exchange the connectors
with each other on one end. Please ensure that the connectors are fully engaged before
proceeding.
4. Use another HDMI cable (maximum length 5m) to connect your HDMI display/projector/sink
device to the HDMI port on the Receiver.
5. Plug the DC power supplies into the HDMI transmitter and receiver, respectively.
6. Power on your HDMI Source and Display to complete the installation.
As well as extending a HDMI signal the Fibre Optic Extender can also repeat IR remote
commands/signals, with the use of the optional IR Repeater Kit (LINDY Number 38006), allowing
you to control your HDMI source whilst up to 3000m away. Simply connect the IR Repeater
Transmitter and Receiver to the relevant ports on the Fibre Optic Transmitter and Receiver. This
functionality is provided in addition to HDMI CEC also supported by this extender.
Troubleshooting
There is no display on the screen.
Check that the DC plugs and jacks used by external power supplies (both the extender units
and others) are firmly connected.
Check that the Fibre Connectors are plugged in correctly and that the Link Status LED is lit.
If it is not lit check if your cable uses a cross over configuration and change it to 1:1.
Check that the HDMI source and display are both powered on and active
Power off all the devices, then power on in this order: first, the transmitter and receiver
modules, then the display and finally the source.
Make sure you have not mixed up the Duplex fibres with each other at one end.
Reduce the length of HDMI cable used, or use a higher quality cable.
Benutzerhandbuch Deutsch
1
Einführung
Dieser HDMI Fibre Optic Extender kann HDMI 1.3b einschließlich aller 1.4a 3D-Signale über
optische Duplexkabel in voller FullHD 1080p@60 Auflösung, erhöhter Farbtiefe mit bis zu 3x
16/48Bit sowie bis zu 4K2K über folgende Distanzen übertragen:
• 300m (Nr.38003) mit Multimode (50/125µm) SC Duplex LWL Kabel oder
• 700m (Nr.38063) mit Single Mode (9/125µm) LC Duplex LWL Kabel oder
• 3000m (Nr.38063) mit Single Mode (9/125µm) LC Duplex LWL Kabel. ohne HDCP
Lieferumfang
LINDY Fibre Optic HDMI Extender (1 x Transmitter, 1 x Receiver)
2x Steckernetzteil mit auswechselbarem Stecker / Multi-Country Power Adapter (5V DC)
Dieses Handbuch
Eigenschaften
Überträgt HDMI oder DVI Signale über LWL Dulpex Kabel bis max. 3000m Kabellänge
Einsetzbar für Home Theater, professionelle Grafikanwendungen und Computer Equipment
Verwendet Standard (Netzwerk) Duplex Fibre Optic LWL Kabel (1:1 verbunden)
Auto Power Save Mode wenn die HDMI Signalquelle kein Bildsignal einspeist
Automatische Laserabschaltung wenn das LWL Kabel bricht oder abgezogen wird
IR-Fernbedienungs-Repeateroption separat erhältlich als LINDY Art.Nr. 38006
Spezifikationen
Über 10Gbit/s totale Bandbreite über 2adrigen (Duplex) Fiber Optic Link
Kompatibel mit der HDMI 1.3b Spezifikation und allen 3D Formaten nach HDMI 1.4a
Unterstützt alle aktuell bekannten Auflösungen und Audioformate
Unterstützt Deep Colour / erhöte Farbtiefe: 30/36/48 Bit bzw. 3x 10/12/18 Bit Farbtiefe
Maximale Länge des SC Duplex Multimodekabels: 300m (Nr.38003) / 700m (Nr.38063) mit
HDMI HDCP-Unterstützung, ohne HDCP bis zu 3000m (Nr.38063)
Maximale Länge der HDMI Anschlusskabel 5m an Ein- oder Ausgang
Unterstützt HDCP
Unterstützt DVI
Abmessungen: 11cm x 7,5cm x 3cm (LxBxH)
Especificaciones del producto
Marca: | Lindy |
Categoría: | extensor AV |
Modelo: | 38063 |
¿Necesitas ayuda?
Si necesitas ayuda con Lindy 38063 haz una pregunta a continuación y otros usuarios te responderán
extensor AV Lindy Manuales
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
13 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
2 Septiembre 2024
1 Septiembre 2024
31 Agosto 2024
extensor AV Manuales
- extensor AV Philips
- extensor AV Abus
- extensor AV Allnet
- extensor AV Nedis
- extensor AV Eminent
- extensor AV Manhattan
- extensor AV Black Box
- extensor AV Tripp Lite
- extensor AV Vision
- extensor AV DataVideo
- extensor AV Techly
- extensor AV Bogen
- extensor AV Matrox
- extensor AV Steren
- extensor AV Digitus
- extensor AV LevelOne
- extensor AV Planet
- extensor AV Konig
- extensor AV D-Link
- extensor AV One For All
- extensor AV Marmitek
- extensor AV Genexis
- extensor AV ATen
- extensor AV Gefen
- extensor AV Peerless
- extensor AV Adder
- extensor AV Monoprice
- extensor AV Crestron
- extensor AV Smart-AVI
- extensor AV StarTech.com
- extensor AV SIIG
- extensor AV Polycom
- extensor AV Micro Connect
- extensor AV Extron
- extensor AV KanexPro
- extensor AV Intelix
- extensor AV ASSMANN Electronic
- extensor AV Blustream
- extensor AV Avocent
- extensor AV Intellinet
- extensor AV Ebode
- extensor AV Ecler
- extensor AV Rose Electronics
- extensor AV Epcom
- extensor AV Kramer
- extensor AV CYP
- extensor AV TV One
- extensor AV SmartAVI
- extensor AV IMG Stage Line
- extensor AV Atlona
- extensor AV HELGI
- extensor AV Lightware
- extensor AV Vivolink
- extensor AV AMX
- extensor AV WyreStorm
- extensor AV Rocstor
- extensor AV MuxLab
- extensor AV Seco-Larm
- extensor AV ConnectPro
- extensor AV Kanex
- extensor AV TechLogix Networx
- extensor AV C2G
- extensor AV SEADA
- extensor AV Comprehensive
- extensor AV PureLink
Últimos extensor AV Manuales
27 Octubre 2024
27 Octubre 2024
22 Octubre 2024
22 Octubre 2024
20 Octubre 2024
19 Octubre 2024
19 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024