Lockncharge REVOLUTION 32 Cabinet Manual de Usario

Lockncharge No categorizado REVOLUTION 32 Cabinet

Lee a continuación 📖 el manual en español para Lockncharge REVOLUTION 32 Cabinet (4 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
www.pclocs.com.au www.lockncharge.com
INSTRUCTIONS:
REVOLUTION 32 CABINET™
C ongratulations on your purchase.
Follow these instructions for easy and fast set up of your Revolution 32 Cabinet.-
For video instructions, go to https://vimeo.com/235852489
Warranty:
PC Locs/LocknCharge warrants the product to be free of defects in design, materials, assembly and craftsmanship from the date of purchase to the original retail
purchaser. Evidence of original purchase will be required to obtain warranty service.
In the event that a defect, malfunction or failure occurs or is discovered during the warranty period, PC Locs/LocknCharge will repair or replace, at its option, the
products which in the reasonable judgment of PC Locs/LocknCharge are deemed defective. All transportation costs shall be borne by the owner and the risk of loss shall
be upon the party initiating the transportation.
The warranty does not apply to any product that has been subject to misuse, tampering, neglect, or accident or as a result of unauthorized alterations or repairs to the
product. The warranty is in lieu of all warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose which are
expressly excluded or disclaimed. In no event will PC Locs/LocknCharge, their directors, officers, employees, or agents be liable for any harm, consequential, incidental,
third party, special or indirect damages whatsoever arising out of the use or inability to use the products even if PC Locs/LocknCharge has been advised of the
possibility of such damages.
PC Locs/LocknCharge obligation is strictly and exclusively limited to the replacement or repair of any defective products. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Disclaimer:
This information is the intellectual property of IWS Global Pty Ltd and may not be distributed, duplicated or copied in part or full without the written permission. Since
the use of this information, the equipment connected and the conditions by which any IWS Global product is used is beyond the control of IWS Global, it is the
obligation of the owner and/or user to determine the correct and safe use of any equipment and product. To the extent that the law permits, any liability which may be
incurred as a result of the use or future use of a product manufactured or sold by IWS Global is limited to the cost of repairing or replacing the failed product or
component at the discretion of IWS Global either within, or outside of warranty periods, and does not extend to any loss or damage which may be caused as a
consequence of misuse or failure of the equipment or product or the information contained herein. IWS Global shall not in any event be liable for economic loss of
profits, indirect, special, bodily injuries or consequential damages.
Specifications and images are for illustration purposes only. Final product may differ and is subject to change without notice.
PC Locs, LocknCharge and the Padlock device are Trademarks of IWS Global Pty Ltd.
Copyright IWS Global Pty Ltd, May 8 201 .
www.pclocs.com.au www.lockncharge.com
ATTACH THE FEET
1. After unboxing gently lay the cabinet on its back using a
piece of packing foam for protection. Attach the four feet.
2. Adjust one foot at a time by turning to ensure Cabinet is
level.
THE CABINET MUST BE SECURED TO A WALL BEFORE USE.
3. Manoeuvre the Cabinet to the location (against the wall)
you wish to install it. Open the top charging compartment
and with a pencil, mark where to drill the holes for
attaching the wall bracket.
4. Drill the holes in the wall (on the marks made in
previous step). Use a 10mm masonry drill the holes.
www.pclocs.com.au www.lockncharge.com
5. Attach the brackets to the wall with the dynabolts
supplied. Insert wall anchors and securely tighten
6. Rout the power cable through the rear of the Cabinet
ready for connecting to a power socket
7. Manoeuvre the Cabinet against the wall where you
attached the wall brackets. Secure with Philips screws
8 . Wall fixing complete
INSTALLING DEVICES
9. Use the key to unlock the top power management
compartment. Note: the PDU’s are mounted to a ‘floating’
rail, allowing it to be adjusted so that power bricks can be
neatly arranged.
10. Connect your power adaptors then rout cables
through grommeted holes – adjust length to suit devices.
Use Velcro cable ties to tidy cables

Especificaciones del producto

Marca: Lockncharge
Categoría: No categorizado
Modelo: REVOLUTION 32 Cabinet

¿Necesitas ayuda?

Si necesitas ayuda con Lockncharge REVOLUTION 32 Cabinet haz una pregunta a continuación y otros usuarios te responderán




No categorizado Lockncharge Manuales

No categorizado Manuales

Últimos No categorizado Manuales