Marmitek IP850 Manual de Usario

Marmitek telefono IP850

Lee a continuación 📖 el manual en español para Marmitek IP850 (4 páginas) en la categoría telefono. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

The ProGuard Interphone provides the ProGuard control panel with an external

microphone and speaker for Two-Way Audio applications.

Installation Pry-off

Speake

Volume

Trimme

Power LED

To install the ProGuard Interphone:

1. Remove the two cover screws.

2. Lift the front cover away from the base.

3. a 2.5m cable with a 6-position RJ-11 connector is supplied

with the ProGuard Interphone. This cable can be spliced to a

24AWG solid four-core cable.

4. Thread the cable through the wiring hole on the back cover.

5. Mount the back cover to the wall using four mounting

screws.

6. Connect the cable to the terminal block on the ProGuard

Interphone as follows:

¬¬

[White] +VPP

®®

[White] OUT (microphone)





[Blue] IN

(speaker)

¯¯

[Orange] GND

Note: The +VPP wire is labeled for convenience

7. Plug the cable into the RJ-11 jack on the ProGuard Main board.

8. Replace the front cover and secure using the two cover screws.

Terminal

Block

Microphone

Sensitivity

Jum

Speake

Microphone

Sensitivity

Trimm

Wiring

Hole

ProGuard Interphone

ProGuard MAIN BOARD

6-Position

RJ-11

Figure 2: Wiring

Connections

Figure 1: ProGuard Interphone (cover off)

Adjusting Speaker Volume and Microphone Sensitivity

The Speaker Volume trimmer, located above the speaker, allows you to adjust the

speaker volume. Turn the trimmer clockwise to increase volume or counter-

clockwise to decrease volume.

You may adjust microphone sensitivity using the Microphone Sensitivity jumper

and trimmer located to the right of the speaker. For high microphone sensitivity,

place the jumper over the bottom two pins in the “H” position. For low microphone

sensitivity, place the jumper over the top two pins in the “L” position. You may also

make fine adjustments to the microphone sensitivity setting using the Microphone

Sensitivity trimmer. Turn the trimmer clockwise to increase sensitivity or counter-

clockwise to decrease sensitivity.

Enabling the Interphone in Programming

The ProGuard control panel’s Microphone/Speaker options allow you to choose

which microphone and speaker shall function during Two-Way Audio

communication. Choose “External” to enable the Interphone to function exclusively

or “Internal & External” to enable the Interphone to function simultaneously with the

ProGuard’s internal microphone and speaker.

The location of the Microphone/Speaker options in the menu is as follows:

•ProGuard 800: Programming, System Options, Mic./Speaker [9412]

Technical Specifications

Operating Voltage: 6-14VDC

Current Consumption: 90mA (standby), 200mA (operation)

Frequency Response: 350-3500Hz

Microphone: Omni-directional electret condenser microphone

Microphone Sensitivity: -46 ± 3dB

Speaker: 8, 1W, 2.5”

Recommended Cable: 4-core solid (24 AWG)

Max Cable Length to Panel: 60m

Operating Temperature: 0-50ºC

Dimensions: 123 x 109 x 27mm

IP850 3

Especificaciones del producto

Marca:	Marmitek
Categoría:	telefono
Modelo:	IP850
Color del producto:	Zwart
Peso.:	13000 g
Ancho:	290 mm
Profundidad:	365 mm
Altura:	850 mm
Tecnología de conectividad:	Bedraad
Tipo de fuente de energía:	AC
Energía promedio:	1400 W
Cantidad por paquete:	1 stuk(s)
Uso recomendado:	DJ
Impedancia:	8 Ohm
Canales de salida de audio:	- kanalen
Colocación de los altavoces:	Floor, Stand-mountable
Número de conductores:	1
altavoz de graves:	Ja
Rango de frecuencia:	30 - 18000 Hz
Sensibilidad:	100 dB
Tipo de altavoz:	3-weg
Diámetro del altavoz de graves:	2 "
Número de controladores de woofer:	2
Posición del orador:	Voorkant