MB Quart NA3-1000.5 Manual de Usario

MB Quart receptor NA3-1000.5

Lee a continuación 📖 el manual en español para MB Quart NA3-1000.5 (5 páginas) en la categoría receptor. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
Setup
Ins
The illustrations below describe the various controls. Refer to
the illustration that matches your amplier.
The level control purpose is to match the output of your source signal to the
amplier. Refer to the section C for detailed instructions.
This switch will set the amplier to have a full frequency output or to lter out high
or low frequencies.
The Bass EQ control will increase the power output at 45Hz for more pronounced
bass. Exercise caution when using this control. Increase the level in small
amounts until distortion is noticed, then back off a little.
1. If possible, with the source unit off, conrm that the primary volume control is
turned down (counter clockwise).
2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplier is illuminated.
3. Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5. Increase the amplier gain (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple ampliers.
Settings
B
This is a critical step to insure your amplier
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
C
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
MBQuart products are designed and engineered in the USA by
www.maxxsonics.com MBQ NA3 QSG 01 - rev3
N
N
N
MIN MAX
1
2
5
LEVEL Adjustment
NA3-560.4
NA3-600.6
NA3-1000.5
X-OVER Switch
BASS BOOST
The Low Pass Filter will cut off the frequencies above the setting. The High Pass
Filter will cut off the frequencies below the setting.
The Subsonic Switch will cut off the frequencies below the setting.
3
4
Frequencies Adjustment
SUBSONIC Switch
To gain access to the NA3
amplier series top mount setting
control panel carefully remove
the six screws and lift the face
plate up.
When you’re nished with the control
panel mindfully put the face plate
back together with the six screws.
Make sure not to over tighten.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
Open Control
Panel
Remote Level
Control
A
D
1
1
1 5
2
2
3
3
3
4
22
2
2
3
3
3
1
1
1
5
5
5
1
1
5
5
2
2
2
3
3

Especificaciones del producto

Marca: MB Quart
Categoría: receptor
Modelo: NA3-1000.5

¿Necesitas ayuda?

Si necesitas ayuda con MB Quart NA3-1000.5 haz una pregunta a continuación y otros usuarios te responderán




receptor MB Quart Manuales

receptor Manuales

Últimos receptor Manuales