Memphis Audio VIV35CV2 Manual de Usario

Memphis Audio altavoz del coche VIV35CV2

Lee a continuación 📖 el manual en español para Memphis Audio VIV35CV2 (7 páginas) en la categoría altavoz del coche. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/7
VIV35CV2 | COMPONENT SPEAKER SET
designed and developed in the united states.
VIV35CV2 | COMPONENT SPEAKER SET
Features
Woofer Technical Information
Woofer Size
RMS Power
PEAK Power
Impedance
Sensitivity (dB)
Magnet Size (oz)
Mounting Depth (in)
Frequency Response
Basket Material
Cone Material
Dust Cap Material
Surround Material
• Cast aluminum Six Five Series basket
• Dual layer composite fiber cone
• Tuned surround for extra flat response
• Audiophile grade features and performance
• Aluminum housed silk tweeter
• Grill included
3.5”
50
100
2Ω
86
6
1.64
100Hz-20kHz
Aluminum
Fiberglass & Foam Composite
Aluminum Bullet
Rubber
Dome Material
Dome Diameter
Voice Coil Diameter
Crossover Type
Tweeter Crossover Freq & Slope (High Pass)
Woofer Crossover Freq & Slope (Low Pass)
Woofer Crossover Freq & Slope (High Pass)
Silk
1.45in // 37mm
.98in // 25mm
2 Way
7Khz, 12dB
6kHz, 12dB
180Hz/100Hz, 12dB
Tweeter Technical Information
Crossover Technical Information
VIV35CV2 | COMPONENT SPEAKER SET
Installation
Prior to setting up your audio system, disconnecting the negative battery terminal from your vehicle is advised.
Prior to cutting or drilling screws, please take time to check clearances on both sides of the mounting surface. Be
mindful of any potential obstacles such as window tracks and motors. Some vehicles are not symmetrical making
it imperative to double check both sides of the vehicle.
Crossover Network
Always mount your crossovers in a location free from moisture and away from moving parts. Crossovers should
not be mounted inside door compartments if possible as doors are not always watertight and moisture may
damage your crossover. Your Crossover must be connected as shown in this manual, failure to follow these
connections may void your warranty and potentially damage your system and vehicle. Failure to properly install
the crossovers may void your warranty. If you are uncomfortable with any of the installation steps it is advised that
you contact your local Memphis Audio dealer.
Speaker Placement
A properly installed component system will yield the best sound for a vehicle. Failure to properly place your
component system can severely hinder your systems performance. A Memphis Audio dealer should be consulted
to properly position your vehicles components for the best possible performance. Ideally the tweeter and woofer
should be installed free from obstacles impeding sound from freely traveling throughout the vehicle. Woofers
should be mounted lower in the vehicle while tweeters typically perform better in a more elevated position. Prior
to cutting any holes or making any alterations to your vehicle, test fit the woofers into the factory mounting
locations to confirm that they clear any obstacles such as window tracks, wire harnesses etc. If you are mounting
the woofers into a non factory location check both sides of the vehicle for obstacles prior to cutting or altering your
vehicle in any way. A speaker cut out template is provided in the box along with this product, again do not rely
solely on the template, be certain to test fit and measure both sides of the vehicle prior to altering your vehicle. To
test the tweeters prior to committing to a mounting location you can simply install the rest of your system and
position your tweeters in various locations using double sided tape until you find an ideal location.
Tweeter Installation
Tweeters should be positioned high, preferably near ear level. Optimum performance will be obtained when
tweeters are angled toward the listener.
The least conspicuous tweeter mounting option is a flush mount. The recessed design provides superior protection
for the tweeter and it blends with the interior of your vehicle.
To mount the tweeter cut a hole in the desired panel. Slide the tweeter into place. Use the included screw and
backer bracket to tighten the tweeter into place. The final installation should look like the above image.
Tweeter
Panel
Bracket
Screw
TWEETER CUT OUT DIAMETER & DEPTH:
Cut Out Diameter: 1.75”
Mounting Depth: 0.53”
0.53”
1.75”

Especificaciones del producto

Marca: Memphis Audio
Categoría: altavoz del coche
Modelo: VIV35CV2

¿Necesitas ayuda?

Si necesitas ayuda con Memphis Audio VIV35CV2 haz una pregunta a continuación y otros usuarios te responderán


altavoz del coche Memphis Audio Manuales

Memphis Audio

Memphis Audio VIV35CV2 Manual de Usario

15 Septiembre 2024

altavoz del coche Manuales

Últimos altavoz del coche Manuales

Sony

Sony XS-W104ES Manual de Usario

16 Octubre 2024
Sony

Sony XS-H1 Manual de Usario

14 Octubre 2024
Alpine

Alpine SWG-1244 Manual de Usario

8 Octubre 2024
JBL

JBL GTO6527 Manual de Usario

8 Octubre 2024
Caliber

Caliber C 12150 Manual de Usario

6 Octubre 2024
Renegade

Renegade RS800A Manual de Usario

6 Octubre 2024
Auna

Auna Coloss 24 Manual de Usario

6 Octubre 2024
Caliber

Caliber BC 112XA Manual de Usario

3 Octubre 2024
Blaupunkt

Blaupunkt GTT 25 Manual de Usario

2 Octubre 2024
JBL

JBL GTO 1214 Manual de Usario

1 Octubre 2024