Metabo CJ 36DA Manual de Usario
Metabo
máquina de aserrar
CJ 36DA
Lee a continuación 📖 el manual en español para Metabo CJ 36DA (92 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/92
Model
Modèle
Modelo CJ 36DA
Cordless Jig Saw
Scie sauteuse sans fi l
Sierra de calar a batería
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and
understand this manual BEFORE operating the power tool. Please keep this manual
available for other users and owners before they use the power tool. This manual should be
stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la
mort ou de sérieuses blessures corporelles !
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent
l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar
en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual
para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este
manual debe ser guardado en un lugar seguro.
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
2
English
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all of the safety precautions, warnings and operating instructions in the instruction manual before
operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,
and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this instruction manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identifi ed by WARNINGS on the power
tool and in this instruction manual.
Never use this power tool in a manner that has not been specifi cally recommended by metabo HPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
3
English
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off -position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles.
A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or remove the battery pack,
if detachable, from the power tool before
making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may aff ect the power tool’s operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations diff erent
from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fi re when used with
another battery pack.
b) Use power tools only with specifi cally
designated battery packs.
Use of any other battery packs may create a risk
of injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may
cause burns or a fi re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, fl ush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modifi ed.
Damaged or modifi ed batteries may exhibit
unpredictable behaviour resulting in fi re,
explosion or risk of injury.
Especificaciones del producto
| Marca: | Metabo |
| Categoría: | máquina de aserrar |
| Modelo: | CJ 36DA |
¿Necesitas ayuda?
Si necesitas ayuda con Metabo CJ 36DA haz una pregunta a continuación y otros usuarios te responderán
máquina de aserrar Metabo Manuales
26 Octubre 2024
18 Septiembre 2024
16 Septiembre 2024
15 Septiembre 2024
9 Septiembre 2024
9 Septiembre 2024
8 Septiembre 2024
5 Septiembre 2024
5 Septiembre 2024
5 Septiembre 2024
máquina de aserrar Manuales
- máquina de aserrar Bosch
- máquina de aserrar AEG
- máquina de aserrar DeWalt
- máquina de aserrar Ford
- máquina de aserrar Silverline
- máquina de aserrar Brennenstuhl
- máquina de aserrar Ferm
- máquina de aserrar Clarke
- máquina de aserrar Ozito
- máquina de aserrar Gude
- máquina de aserrar Makita
- máquina de aserrar Draper
- máquina de aserrar Hitachi
- máquina de aserrar Black And Decker
- máquina de aserrar Vonroc
- máquina de aserrar Remington
- máquina de aserrar ACG
- máquina de aserrar Stanley
- máquina de aserrar Skil
- máquina de aserrar Hyundai
- máquina de aserrar Hilti
- máquina de aserrar Ryobi
- máquina de aserrar Florabest
- máquina de aserrar Festool
- máquina de aserrar Parkside
- máquina de aserrar Worx
- máquina de aserrar Meec Tools
- máquina de aserrar Milwaukee
- máquina de aserrar Hikoki
- máquina de aserrar Sun Joe
- máquina de aserrar Dremel
- máquina de aserrar Sovereign
- máquina de aserrar Tacklife
- máquina de aserrar Hazet
- máquina de aserrar Einhell
- máquina de aserrar Baumr-AG
- máquina de aserrar Ferrex
- máquina de aserrar Husqvarna
- máquina de aserrar Craftsman
- máquina de aserrar Power Craft
- máquina de aserrar Powerplus
- máquina de aserrar Stiga
- máquina de aserrar Porter-Cable
- máquina de aserrar Cotech
- máquina de aserrar Genesis
- máquina de aserrar Trotec
- máquina de aserrar Cobra
- máquina de aserrar Texas
- máquina de aserrar Spear & Jackson
- máquina de aserrar Scheppach
- máquina de aserrar Atika
- máquina de aserrar McCulloch
- máquina de aserrar Sterwins
- máquina de aserrar Matrix
- máquina de aserrar Stihl
- máquina de aserrar Dolmar
- máquina de aserrar Flex
- máquina de aserrar Prime3
- máquina de aserrar Zipper
- máquina de aserrar Mafell
- máquina de aserrar Fieldmann
- máquina de aserrar Max
- máquina de aserrar Grizzly
- máquina de aserrar Solo
- máquina de aserrar Cocraft
- máquina de aserrar MTM
- máquina de aserrar Maruyama
- máquina de aserrar Herkules
- máquina de aserrar Meister Craft
- máquina de aserrar Toolcraft
- máquina de aserrar RIDGID
- máquina de aserrar Batavia
- máquina de aserrar Proxxon
- máquina de aserrar Gardenline
- máquina de aserrar Holzmann
- máquina de aserrar Fein
- máquina de aserrar Oregon Scientific
- máquina de aserrar Elu
- máquina de aserrar Max Bahr
- máquina de aserrar Plantiflor
- máquina de aserrar Goon
- máquina de aserrar Triton
- máquina de aserrar BGU
- máquina de aserrar Wolfcraft
- máquina de aserrar Dedra
- máquina de aserrar Verto
- máquina de aserrar Anova
- máquina de aserrar Rikon
- máquina de aserrar Elektra Beckum
- máquina de aserrar Duro Pro
- máquina de aserrar Toolson
- máquina de aserrar Jonsered
- máquina de aserrar MSW
- máquina de aserrar Royal Catering
- máquina de aserrar Ultranatura
- máquina de aserrar Einhell Bavaria
- máquina de aserrar McKenzie
- máquina de aserrar Bavaria By Einhell
- máquina de aserrar Donau Elektronik
- máquina de aserrar Chicago Pneumatic
- máquina de aserrar Rona
- máquina de aserrar Bestgreen
- máquina de aserrar CMI
- máquina de aserrar MacAllister
- máquina de aserrar TAURUS Titanium
- máquina de aserrar Maxbear
- máquina de aserrar Evolution
- máquina de aserrar Extralink
- máquina de aserrar Yellow Garden Line
- máquina de aserrar Stalco
Últimos máquina de aserrar Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
26 Octubre 2024
22 Octubre 2024
21 Octubre 2024