Metra 95-9307B Manual de Usario

Lee a continuación 📖 el manual en español para Metra 95-9307B (4 páginas) en la categoría equipo de coche. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 12/14/2015 INST95-9307B
Installation instructions for part 95-9307B
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
ISO DDIN radio provision
Painted scratch resistant matte black
A) ISO DDIN radio housing B) ISO DDIN radio trim plate C) ISO DDIN brackets • D) (4) Panel clips
E) (8) ISO screws • F) (2) #8 x 1/2 Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-9003 • 70-8590 • 70-8591
Antenna Adapter:40-EU10 • 40-VW10
Phillips Screwdriver Torx T-10 Screwdriver Panel Removal Tool Cutting Tool or FileSocket Wrench
TOOLS REQUIRED
BMW 5 Series
5-Series (Without NAV) 1997-2003
M5 (Without NAV) 2000-2003
95-9307B
A B C D E
F
Dash Disassembly .............................................. 2-3
Kit Assembly
ISO DDIN radio provision ...................................... 4
Table of Contents
95-9307B
2
1.
Remove the volume knob by pulling
out towards the rear of the vehicle.
2. Turn the exposed screw 90º using
a T-10 Torx screwdriver, pull out
on the bottom of the radio, then
unplug and remove the lower
portion of the radio. (Figure A)
Note: Leave the Torx driver in place
to aid in pulling out the radio.
3. Remove the (2) T-10 Torx screws
securing the top portion of the
radio, then unplug and remove the
radio. (Figure B)
4. Unclip and remove the wood trim
panels above the glove box, and to
the left of the radio. (Figure C)
Dash Disassembly
5. Remove the (1) Phillips screw
securing each side panel on the
center console, and then slide
the panels forward to unclip and
remove them. (Figure D)
6. Open the glove box, and then
unclip and remove the glove box
side supports. (Figure E)
Continued on the next page
(Figure B) (Figure D)
(Figure C)(Figure A) (Figure E)
95-9307B
Dash Disassembly
(Figure F) (Figure H)
(Figure G) (Figure I)
(Figure J)
7. Remove the (2) Phillips screws
securing the panel located inside the
left side of the glove box cavity, and
then remove the panel. (Figure F)
8.
Remove the (3) Phillips screws
securing the glove box to the
lower dash panel, and then let the
assembly hang. (Figure G)
9. Remove the (4) Phillips screws
above the glove box, the (1) behind
the cover on the right side of the
lower dash panel, and the (2) on
the lower dash panel to the left of
the radio. (Figure H)
10. Remove the (4) Phillips screws
securing the radio sub-dash panel
to the lower dash panel. (Figure I)
Note: These (4) screws will be
reused in kit assembly.
11.
Carefully pull the right side of the
lower dash panel outward to gain
access to the radio sub-dash panel,
and then remove the radio sub-
dash panel from the radio cavity.
(Figure J)
Continue to kit assembly
3

Especificaciones del producto

Marca: Metra
Categoría: equipo de coche
Modelo: 95-9307B

¿Necesitas ayuda?

Si necesitas ayuda con Metra 95-9307B haz una pregunta a continuación y otros usuarios te responderán




equipo de coche Metra Manuales

equipo de coche Manuales

Últimos equipo de coche Manuales