Mikrotik D-5G-30D3 Manual de Usario

Mikrotik antena de televisión D-5G-30D3

Lee a continuación 📖 el manual en español para Mikrotik D-5G-30D3 (4 páginas) en la categoría antena de televisión. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

KJ L M O Q RN P S

Parabolic Dish

Antenna Feed

Feed Bracket

Back Plate

Pole Clamp

Case Holder

RF Cable

Self-Bonding Tape Slice

M8 U-Bolt

M6x20 Bolt

M4x12 Bolt

M4 Wing Nut

M4 Serrated Washer

M6 Nut

M6 Spring Lock Washer

M6 Washer

M8 Nut

M8 Spring Lock Washer

M8 Fender Washer

ITEM DESCRIPTION QTY

MikroTik Antenna assembly preview

MikroTik Antenna assembly preview back* MikroTik Antenna assembly preview front

A B C D

E F G H I

MikroTik Antenna D-5G-30D3

Quick setup guide and warranty information

Package contents

MikroTik Radio

*The preview is valid if a MikroTik RB900 series outdoor device

(sold separately) is installed.

Installation Guide

0. Items Required

• 10mm Wrench 13mm Wrench • • PH2 Screw Driver •

• This guide is written to be used with a MikroTik RB900 series outdoor

device (sold separately) •

1. Install Back Plate to Parabolic Dish

Install Back Plate [D] to Parabolic Dish [A] using:

[J] M6x20 Bolt x 4 pcs;

[P] M6 Washer x 4 pcs;

[O] M6 Spring Lock Washer x 4 pcs;

[N] M6 Nut x 4 pcs.

Important:

• Back Plate [D] must be aligned respecvely to a bore in the

Parabolic Dish [A] - see Fig. 1;

• M6 Nut [N] ghtening torque must be approximately 5 Nm.

2. Install Antenna Feed

Install Antenna Feed [B] to Parabolic Dish [A] using:

[C] Feed Bracket x 1 pc;

[K] M4x12 Bolt x 4 pcs;

[M] M4 Serrated Washer x 4 pcs.

Install grounding fasteners:

[L] M6 Wing Nut x 1 pc;

[M] M4 Serrated Washer x 1 pc.

Important:

• Antenna Feed [B] and Feed Bracket [C] must be aligned respecvely

to the alignment bore in the Parabolic Dish [A] - see Fig. 2;

• M4x12 Bolt [N] ghtening torque must be approximately 2 Nm.

3. Install Pole Clamp

Install Pole Clamp [E] to Back Plate [D] - see Fig. 3, using:

[J] M6x20 Bolt x 1 pc;

[P] M6 Washer x 1 pc;

[O] M6 Spring Lock Washer x 1 pc;

[N] M6 Nut x 1 pc.

Important:

• Do not ghten M6 Nut [N] ﬁrmly unl step 7.

FIG. 1

FIG. 2

C BMK

FIG. 3

J E O ND P

FIG. 4.2FIG. 4.1

M3x8FL

4. Aach MikroTik Radio to Back Plate

Aach a to Case Holder [F] using:MikroTik RB900 series outdoor device

[-] M3x8 Bolt x 4 pcs (Comes with MikroTik Radio) - see Fig. 4.1.

Aach Case Holder [F] to Back Plate [D] by ﬁng Case Holder’s hinges

into the Back Plate’s ﬂange - see Fig. 4.2. Secure Case Holder using:

[L] M4 Wing Nut x 1 pc.

Important:

• M3x8 Bolt [-] ghtening torque must be approximately 1.5 Nm.

FIG. 5

Ø = 70mmMAX FIG. 6

R QI S

FIG. 7

Q N D

5. Install RF Cables

Remove the cover from MikroTik Radio and install the RF Cables [G].

Connect vercal polarizaon (arrow V) to CH0, horizontal polarizaon

(arrow H) to CH1 - see Fig. 5.

Insulate the RF Cable [G] ends which are connected to Antenna Feed [B]

by using: [H] Self-Bonding Tape Slice x 2pcs.

• Remove the plastic liner from both sides;

• Stretch the tape to 2/3 of its width;

• Apply half-lapped layers clockwise.

The RF Cable [G] ends which are connected to MikroTik Radio are insulated

by the cover.

Fit back the MikroTik Radio cover.

Important:

• RF Cables [G] connector ghtening torque must be approximately 0.5 Nm.

6. Aach Antenna to Pole

MikroTik Antenna D-5G-30D3 is design to ﬁt the pole diameter up

to 70mm( 2.75”).

Aach MikroTik Antenna to pole as shown in Fig. 6 using:

[I] M8 U-Bolt x 2 pcs;

[S] M8 Fender Washer x 4 pcs;

[R] M8 Spring Lock Washer x 4 pcs;

[Q] M8 Nut x 4 pcs.

Important:

• Do not ghten M8 Nuts [Q] ﬁrmly unl step 7.

7. Adjust Azimuth and Elevaon

The Azimuth and Elevaon can be adjusted if M8 Nuts [Q] are slightly

loosen. In order to set the azimuth rotate the antenna around the pole

- see Fig. 7. The elevaon can be set by turning Back Plate [D].

Aer seng the azimuth and elevaon, ghten ﬁrmly the corresponding

fasteners - see Fig. 6.

Important:

• M6 Nut [N] ghtening torque must be approximately 5 Nm.

• M8 Nuts [Q] ghtening torque must be approximately 20 Nm.

Especificaciones del producto

Marca:	Mikrotik
Categoría:	antena de televisión
Modelo:	D-5G-30D3

¿Necesitas ayuda?

Si necesitas ayuda con Mikrotik D-5G-30D3 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

antena de televisión Mikrotik Manuales

Mikrotik D-5G-30D3-PA Manual de Usario

6 Septiembre 2024

Mikrotik D-5G-30D3 Manual de Usario

6 Septiembre 2024

Mikrotik Sleeve30 Manual de Usario

6 Septiembre 2024

antena de televisión Manuales

Últimos antena de televisión Manuales

Thomson ANT1538BK Manual de Usario

15 Octubre 2024

Xoro HAN 150 Manual de Usario

11 Octubre 2024

One For All SV 9482 Manual de Usario

9 Octubre 2024

Kathrein ESU 57 Manual de Usario

6 Octubre 2024

Uniden AW880BKL Manual de Usario

4 Octubre 2024

One For All SV 9435 Manual de Usario

30 Septiembre 2024

Blaupunkt Shark Line A-R T 06-M Manual de Usario

23 Septiembre 2024

Uniden ATX970W Twin Manual de Usario

18 Septiembre 2024

TP Link TL-ANT5819MS Manual de Usario

18 Septiembre 2024

EMOS J0704 Manual de Usario

17 Septiembre 2024