Milwaukee 2734-20 Manual de Usario

Milwaukee máquina de aserrar 2734-20

Lee a continuación 📖 el manual en español para Milwaukee 2734-20 (36 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/36

Cat. No. / No de cat.

2734-20

M18 FUEL™ 10" DUAL BEVEL COMPOUND SLIDING MITER SAW

SCIE À ONGLETS COMPOSÉS COULISSANTE À DOUBLE

BISEAU DE 254 mm (10") M18 FUEL™

SIERRA DE INGLETE COMPUESTA DESLIZANTE DE BISEL

DUAL DE 254 mm (10") M18 FUEL™

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to

your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an exten-

sion cord suitable for outdoor use. Use of a cord suit-

able for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair can

be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action c

an cause

severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn

it on and o󰀨. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Pow-

er tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may a󰀨ect

the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

• Use the po

wer tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations di󰀨erent

from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of re when used

with another battery pack.

• Use power tools only with specically designated

battery packs. Use of any other battery packs may

create a risk of injury and re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or a re.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact acci-

dentally occurs, ush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or

modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or

risk of injury.

• Do not expose a battery pack or tool to re or exces-

sive temperature. Exposure to re or temperature

above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specied in the instructions. Charging im-

properly or at temperatures outside the specied range

may damage the battery and increase the risk of re.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

• Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SPECIFIC SAFETY RULES FOR

MITER SAWS

• Miter saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-o󰀨

wheels for cutting ferrous material such as bars,

rods, studs, etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from abrasive

cutting will burn the lower guard, the kerf insert and

other plastic parts.

• Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand,

you must always keep your hand at least 100 mm

from either side of the saw blade. Do not use this

saw to cut pieces that are too small to be securely

clamped or held by hand. If your hand is placed too

close to the saw blade, there is an increased risk of

injury from blade contact.

• The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut “freehand”

in any way. Unrestrained or moving workpieces could

be thrown at high speeds, causing injury.

• Push the saw through the workpiece. Do not pull

the saw through the workpiece. To make a cut, raise

the saw head and pull it out over the workpiece

without cutting, start the motor, press the saw head

down and push the saw through the workpiece.

Cutting on the pull stroke is likely to cause the saw

blade to climb on top of the workpiece and violently

throw the blade assembly towards the operator.

• Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your

left hand or vice versa is very dangerous.

• Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not be

obvious and you may be seriously injured.

• Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or

warped workpieces can twist or shift and may cause

binding on the spinning saw blade while cutting. There

should be no nails or foreign objects in the workpiece.

• Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small

debris or loose pieces of wood or other objects that con-

tact the revolving blade can be thrown with high speed.

• Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

• Ensure the miter saw is mounted or placed on a level,

rm work surface before use. A level and rm work sur-

face reduces the risk of the miter saw becoming unstable.

• Plan your work. Every time you change the bevel

or mitre angle setting, make sure the adjustable

fence is set correctly to support the workpiece and

will not interfere with the blade or the guarding

system. Without turning the tool “ON” and with no

workpiece on the table, move the saw blade through

a complete simulated cut to assure there will be no

interference or danger of cutting the fence.

• Provide adequate support such as table extensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or

wider than the miter saw table can tip if not securely

supported. If the cut-o󰀨 piece or workpiece tips, it can

lift the lower guard or be thrown by the spinning blade.

• Do not use another person as a substitute for a

table extension or as additional support. Unstable

support for the workpiece can cause the blade to bind

or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

• The cut-o󰀨 piece must not be jammed or pressed

by any means against the spinning saw blade. If

conned, i.e. using length stops, the cut-o󰀨 piece could

get wedged against the blade and thrown violently.

• Always use a clamp or a fixture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

• Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

• If the workpiece or blade becomes jammed, turn

the mitre saw o󰀨. Wait for all moving parts to stop

and disconnect the plug from the power source

and/or remove the battery pack. Then work to

free the jammed material. Continued sawing with

a jammed workpiece could cause loss of control or

damage to the miter saw.

• After nishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-o󰀨 piece. Reaching with

your hand near the coasting blade is dangerous.

• Hold the handle rmly when making an incomplete

cut or when releasing the switch before the saw

head is completely in the down position. The

braking action of the saw may cause the saw head to

be suddenly pulled downward, causing a risk of injury.

•

WARNING

To reduce the risk of injury in ap-

plications that produce a consid-

erable amount of dust, use an OSHA compliant

dust extraction solution in accordance with the

solution’s operating instructions.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every

situation that could result in a dangerous outcome.

Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond

your capability; contact Milwaukee Tool or a trained

professional for additional information or training.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

Especificaciones del producto

Marca:	Milwaukee
Categoría:	máquina de aserrar
Modelo:	2734-20

¿Necesitas ayuda?

Si necesitas ayuda con Milwaukee 2734-20 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

máquina de aserrar Milwaukee Manuales

Milwaukee M12 2420-21 Manual de Usario

6 Octubre 2024

Milwaukee M12 JS-402B Manual de Usario

3 Octubre 2024

Milwaukee M18 FTCHS14 Manual de Usario

19 Septiembre 2024

Milwaukee MXF COSCG2 Manual de Usario

19 Septiembre 2024

Milwaukee MSUV280 Manual de Usario

16 Septiembre 2024

Milwaukee HD18 JSB-402C Manual de Usario

16 Septiembre 2024

Milwaukee M18 Fuel 2720-22 Manual de Usario

15 Septiembre 2024

Milwaukee M18 BJS Manual de Usario

14 Septiembre 2024

Milwaukee SCS 65 Q Manual de Usario

14 Septiembre 2024

Milwaukee M12 BS Manual de Usario

14 Septiembre 2024

máquina de aserrar Manuales

Últimos máquina de aserrar Manuales

Hikoki C 6BU3 Manual de Usario

27 Octubre 2024

Dedra DED7060 Manual de Usario

27 Octubre 2024

Einhell KGS 190 Manual de Usario

27 Octubre 2024

Sun Joe SWJ599E Manual de Usario

27 Octubre 2024

McCulloch CSE1935S Manual de Usario

27 Octubre 2024

Hikoki C10FSB Manual de Usario

27 Octubre 2024

Metabo STA 18 LTX 150 BL Manual de Usario

26 Octubre 2024

Craftsman 917.377662 Manual de Usario

26 Octubre 2024

Maruyama MCV51 Manual de Usario

26 Octubre 2024

Powerplus POWX53300T Manual de Usario

22 Octubre 2024