Milwaukee 48-44-0070 Manual de Usario
Milwaukee
par de tijeras
48-44-0070
Lee a continuación 📖 el manual en español para Milwaukee 48-44-0070 (2 páginas) en la categoría par de tijeras. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
00
0
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
®
REVISED BULLETIN DATE
CATALOG NO.
SERVICE PARTS LIST
MILWAUKEE TOOL CORPORATION 13135 W.
LISBON RD., BROOKFIELD, WI 53005
Drwg. 2
BULLETIN NO.
STARTING
SERIAL NO.
WIRING INSTRUCTION
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
18 GAUGE SHEAR HEAD ASSEMBLY
48-08-0500
Oct 19. 20
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 48-08-0500 Shear Head Assy. (Includes 2 thru 11) (1)
2 06-75-2115 10-24 x 1-1/4 Skt. Hd. Cap Screw (3)
3 43-76-0400 Shear Housing (1)
4 45-88-7310 Washer (1)
5 43-16-0100 Eccentric Assembly (1)
6 43-84-0460 Knurled Insert (3)
7 48-44-0170 Blade - Right Side (1)
8 42-40-0520 Bushing (2)
9 48-44-0150 Blade - Center (1)
10 48-44-0160 Blade - Left Side (1)
11 49-96-0070 5/32 Hex Allen Wrench (1)
FIG. LUBRICATION:
3,7,8 During assembly, use a dab of Type "E" Grease,
No. 49-08-4122 to lubricate flats, pivot hole and sides of
center blade (8), eccentric assembly (3) and bushing (7).
54-40-8220
*
Bottom view of
Shear Head
Assembly
Bushings
When servicing Shear Head Assembly No. 48-08-0500 pay close attention to the
placement of the Bushings. One is to be placed in the hole of the Center Blade
and is to be held in place with the front most screw on the Shear Housing. The
other bushing is to be located below the small concave notch of the Center Blade
and is to be secured with the middle screw on the Shear Housing. Prior to assem-
bly, it is recommended to use Type 'E' Grease, No. 49-08-4122 on the following
areas: Place a dab of grease in the pivot (bushing) hole and on the bushing notch
oftheCenterBlade.PlaceadabofgreaseontherearatsoftheCenterBlade.
Coat both bushings completely with grease.
Place a liberal amount of grease on the
entire Eccentric Assembly.
Illustration shown without tool attached
for clarity of spreader wrench
placement on shear head
Prior to using the
spreader wrench,
this screw must be
loosened two turns.
Remove this screw.
Insert the end of the
spreader wrench into the bottom
rear opening of shear head assembly
as shown. Twist the wrench in a clockwise
direction (allowing the rounded cam to roll and
spread the back of the shear housing). Spreader wrench
will rotate approximately 1/4 turn and stop at next flat after cam.
To remove spreader tool, turn counter-clockwise.
Front View
REMOVING SHEAR HEAD ASSEMBLY FROM TOOL
SERVICE TOOLS:
Spreader Wrench No. 61-30-0300
for 14 Gauge Shear Head 48-08-0505
used on Shear No. 2636-20
for 18 Gauge Shear Head 48-08-0507
used on Shear 2637-20
Spreader Wrench No. 61-30-0310
for 18 Gauge Shear Head 48-08-0500
used on Shears 2635-20 and 6852-20
Especificaciones del producto
| Marca: | Milwaukee |
| Categoría: | par de tijeras |
| Modelo: | 48-44-0070 |
¿Necesitas ayuda?
Si necesitas ayuda con Milwaukee 48-44-0070 haz una pregunta a continuación y otros usuarios te responderán
par de tijeras Milwaukee Manuales
3 Octubre 2024
14 Septiembre 2024
10 Agosto 2024
9 Agosto 2024
1 Agosto 2024
par de tijeras Manuales
- par de tijeras DeWalt
- par de tijeras Makita
- par de tijeras Hitachi
- par de tijeras Black And Decker
- par de tijeras Rowenta
Últimos par de tijeras Manuales
7 Octubre 2024
23 Septiembre 2024
18 Septiembre 2024
17 Septiembre 2024
12 Septiembre 2024
22 Agosto 2024
14 Agosto 2024
3 Agosto 2024
2 Agosto 2024
24 Julio 2024