Milwaukee TILT-LOK 6390-21 Manual de Usario

Milwaukee máquina de aserrar TILT-LOK 6390-21

Lee a continuación 📖 el manual en español para Milwaukee TILT-LOK 6390-21 (32 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/32

Cat. No. / No de cat.

6390-20, 6394

HEAVY-DUTY CIRCULAR SAW WITH TILT-LOK™

ADJUSTABLE HANDLE

SCIES CIRCULAIRES INDUSTRIELLES AVEC POIGNEE

« TILT-LOK™ »

SIERRA CIRCULAR PARA TRABAJO PESADO CON

EMPUÑADURA TILT-LOK™ (INCLINABLE-FIJABLE)

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching outlets will reduce risk

of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools may

result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair can

be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn

it on and o󰀨. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Pow-

er tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may a󰀨ect

the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are

caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations di󰀨erent

from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

SERVICE

• Have your power tool serviced by a qualied repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SPECIFIC SAFETY RULES FOR

CIRCULAR SAW

Cutting procedures

•

DANGER

Keep hands away from cutting area

and the blade. Keep your second

hand on auxiliary handle, or motor housing. If both

hands are holding the saw, they cannot be cut by the

blade.

• Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

• Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

• Never hold the workpiece in your hands or across

your leg while cutting. Secure the workpiece to a

stable platform. It is important to support the work

properly to minimise body exposure, blade binding,

or loss of control.

• Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring or its own

cord. Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

• When ripping, always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance of blade binding.

• Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw

will run o󰀨-centre, causing loss of control.

• Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation.

Further safety instructions for all saws

Kickback causes and related warnings

– Kickback is a sudden reaction to a pinched, jammed

or misaligned saw blade, causing an uncontrolled saw

to lift up and out of the workpiece toward the operator;

– When the blade is pinched or jammed by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator;

– If the blade becomes twisted or misaligned in the cut,

the teeth at the back edge of the blade can dig into

the top surface of the wood causing the blade to climb

out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below:

• Maintain a rm grip with both hands on the saw and

position your arms to resist kickback forces. Posi-

tion your body to either side of the blade, but not

in line with the blade. Kickback could cause the saw

to jump backwards, but kickback forces can be con-

trolled by the operator, if proper precautions are taken.

• When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes

to a complete stop. Never attempt to remove the

saw from the work or pull the saw backward while

the blade is in motion or kickback may occur. In-

vestigate and take corrective actions to eliminate the

cause of blade binding.

• When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material. If saw blade is binding,

it may walk up or kickback from the workpiece as the

saw is restarted.

• Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed under

the panel on both sides, near the line of cut and near

the edge of the panel.

• Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

• Blade depth and bevel adjusting locking levers must

be tight and secure before making cut. If blade adjust-

ment shifts while cutting, it may cause binding and kickback.

• Use extra caution when sawing into existing walls

or other blind areas. The protruding blade may cut

objects that can cause kickback.

Lower guard function

• Check lower guard for proper closing before each

use. Do not operate the saw if lower guard does

not move freely and close instantly. Never clamp or

tie the lower guard into the open position. If saw is

accidentally dropped, lower guard may be bent. Raise

the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or

any other part, in all angles and depths of cut.

• Check the operation of the lower guard spring. If

the guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

• The lower guard may be retracted manually only for

special cuts such as “plunge cuts” and “compound

cuts”. Raise the lower guard by the retracting han-

dle and as soon as the blade enters the material, the

lower guard must be released. For all other sawing,

the lower guard should operate automatically.

• Always observe that the lower guard is covering

the blade before placing saw down on bench or

oor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop after

switch is released.

•

WARNING

To reduce the risk of injury in ap-

plications that produce a consider-

able amount of dust, use an OSHA compliant dust

extraction solution in accordance with the solu-

tion’s operating instructions.

• Always use common sense and be cautious when

using tools. It is not possible to anticipate every

situation that could result in a dangerous outcome.

Do not use this tool if you do not understand these

operating instructions or you feel the work is beyond

your capability; contact Milwaukee Tool or a trained

professional for additional information or training.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

•

WARNING

Some dust created by power sanding,

sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

lter out microscopic particles.

SPECIFICATIONS

Amps ...................................................................15

No Load RPM ..................................................6300

Blade Size ..................................................... 7-1/4"

Arbor ................................................................. 5/8"

Depth of Cut at 90° ............................. 0 to 2-15/32"

Depth of Cut at 45° ............................. 0 to 1-13/16"

Cat. No. 6390-20 .....................................................

Volts .......................................................120 AC/DC

Cat. No. 6394 ...........................................................

Volts .................................................... 120 AC Only

Especificaciones del producto

Marca:	Milwaukee
Categoría:	máquina de aserrar
Modelo:	TILT-LOK 6390-21
Color del producto:	Groen
Peso.:	32 g
Ancho:	58 mm
Profundidad:	80 mm
Altura:	20 mm
Peso del embalaje:	90 g
Ancho del embalaje:	125 mm
Empaquetadura en profundidad:	175 mm
Altura del embalaje:	30 mm
Tipo de embalaje:	Doos
País de origen:	China
Destinado a:	PC
Interno:	Ja
Número de puertos USB 3.2 Gen 2 (3.1 Gen 2) Tipo C:	2
Compatible con Linux:	Ja
Guía de Instalación Rápida:	Ja
Interfaz de host:	PCIe
Controladores suministrados:	Ja
Soportes de montaje incluidos:	Ja
conjunto de chips:	ASM1142
Altura del paquete principal (exterior):	405 mm
Ancho del embalaje principal (exterior):	340 mm
Peso bruto del embalaje principal (exterior):	2700 g
Longitud del paquete principal (exterior):	205 mm
Cantidad por caja principal (exterior):	30 stuk(s)
Código del Sistema Armonizado (SA):	84733020
intercambio en caliente:	Ja
Estándar de tarjeta de expansión:	PCI 2.0
Velocidad de transferencia de datos (máx.):	10 Gbit/s
Número de puertos SATA internos:	1
Interfaz de salida:	USB 3.2 Gen 2 (3.1 Gen 2)
Soporte UASP:	Ja
Tipo de conector de alimentación SATA:	SATA 15-pin