Moxa NPort 5250A Manual de Usario

Moxa servidor NPort 5250A

Lee a continuación 📖 el manual en español para Moxa NPort 5250A (6 páginas) en la categoría servidor. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
P/N: 1802052000014
*1802052000014*
NPort 5200A Series
Quick Installation Guide
Version 2.3, January 2021
Technical Support Contact Information
www.moxa.com/support
21 . A20 Moxa Inc ll rights reserved.
- - 2
Overview
NPort 5200A series of device servers are compact, palm-sized data
communication devices that allow you to control RS- 232 (NPort 5210A),
RS- -422/485 (NPort 5230A), and RS 232/422/485 (NPort 5250A) serial
devices over a TCP/IP based Ethernet.-
NOTE
“- T” indicates an extended temperature model.
Package Checklist
Before installing the NPort 5200A device server, verify that the package
contains the following items:
1 NPort 5200A serial device server
- 4 stick on pads
Quick Installation Guide
Product Warranty Statement
Optional Accessory
- - DK 35A: DIN Rail Mounting Kit (35 mm)
Notify your sales representative if any of the above items are missing or
damaged.
Hardware Introduction
As shown in the following figures, the NPort 5200A series device servers
have two male DB9 ports for transmitting RS-232 (NPort 5210A), or
RS- -232/422/485 (NPort 5250A) serial data and have two 5 pin terminal
block ports for transmitting RS- 422/485 (NPort 5230A).
Reset Button—Press and hold the Reset button for 5 seconds to load
factory defaults: Use a pointed object, such as a straightened paper clip
- - 3
or toothpick, to depress the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, release the reset
button.
LED Indicators—NPort 5200A’s top panel has four LED indicators, which
are described in the following table.
LED
Name
LED
Color
LED Function
Ready
R ed
Steady on:
Power is on and the NPort is booting up.
Blinking:
Indicates an IP conflict, or DHCP or BOOTP
server is not responding properly.
G reen
Steady on:
Power is on and the NPort is functioning
normally.
Blinking:
The NPort has been located by the NPort
Administrator’s Location function.
O ff
Power is off, or a power error..
Link
O range
10 Mbps Ethernet connection.
G reen
100 Mbps Ethernet connection.
O ff
Ethernet cable is disconnected.
P1, P2
O range
Serial port is receiving data.
G reen
Serial port is transmitting data.
O ff
No data is being transmitted or received through the
seri al port.
Adjustable pull high/low resistor and terminator for RS- 422/485
Remove the NPort 5230A/5250A’s top
cover and you will find DIP switches to
adjust each serial port’s pull
-high,
pull
-
low, and terminator. Do not use the 1
K
Ω -setting with RS
232 mode, as doing so
will degrade the RS
-232 signals and
shorten the communications range.
SW
1
2
3
Pull- high resistor
Pull- high resistor
Terminator
ON
1
1
120 Ω
OFF
*150
*150
*–
*Default

Especificaciones del producto

Marca: Moxa
Categoría: servidor
Modelo: NPort 5250A

¿Necesitas ayuda?

Si necesitas ayuda con Moxa NPort 5250A haz una pregunta a continuación y otros usuarios te responderán




servidor Moxa Manuales

servidor Manuales

Últimos servidor Manuales