Moxa NPort P5150A Manual de Usario

Moxa servidor NPort P5150A

Lee a continuación 📖 el manual en español para Moxa NPort P5150A (5 páginas) en la categoría servidor. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/5

P/N: 1802051501013

*1802051501013*

NPort P5150A Series

Quick Installation Guide

Vers 20ion January 2.3, 21

Technical Support Contact Information

www.moxa.com/support



21 . A20 Moxa Inc ll rights reserved.

- - 2

Overview

NPort P5150A series of device servers , -are compact palm sized data

communication device allow serial s that -you to control RS 232/422/485

devices over a TCP/IP based Ethernet- .

NOTE

“-T” indicates an extended temperature model.

Package Checklist

Before installing the NPort P5150A series of device server, verify that the

package contains the following items:

• 1 NPort P5150A serial device server

• - 4 stick on pads

• Quick Installation Guide

• Product Warranty Statement

Optional Accessory

• - -R DK 35A: DIN ail Mounting Kit (35 mm)

Notify your sales representative if any of the above items are missing or

damaged.

Hardware Introduction

As shown in the following figures, NPort P5150A series of device servers

have RS one male DB9 port for transmitting - . 232/422/485 serial data

Reset Button—Press and hold the Reset button for 5 seconds to load

factory defaults: Use a pointed object, such as a straightened paper clip

or toothpick, to depress the reset button. This will cause the Ready LED to

blink on and off. Once the Ready LED stops blinking (after about 5

seconds), release the reset button and the device server will start to load

the factory defaults.

- - 3

WARNING

The equipment is designed for in-building installation only

and is not intended to be connected to exposed (outside

plant) networks.

This equipment is intended to be used in a

Restricted Access

Location.

This product is intended to be supplied by an UL60950-

1 and

IEC60950-1 certified Power Unit marked “LPS” and rated

output rating: 12 to 48 VDC, 0.18 A minimum, 75°C.

LED Indicators— NPort P5150A’s top panel has three LED indicators,

which are described in the following table.

LED

Name

LED

Color

LED Function

Ready

R ed

Steady on:

Power is on and the NPort is booting up.

Blinking:

Indicates an IP conflict, or DHCP or BOOTP

server is not responding properly.

G reen

Steady on:

Power is on and the NPort is functioning

normally.

Blinking:

The NPort has been located by the NPort

Administrator’s Location function.

O ff

Power is off, or a power error..

Link

O range

10 Mbps Ethernet connection.

G reen

100 Mbps Ethernet connection.

O ff

Ethernet cable is disconnected.

Tx/Rx

O range

Serial port is receiving data.

G reen

Serial port is transmitting data.

O ff

No data is being transmitted or received through the

seri al port.

Adjustable pull high/low resistor and terminator for RS- 485

Remove the NPort P5150A’s top cover and

you will find DIP switches to adjust each

serial port’s pull

- -high, pull low, and

terminator.

Do not use the 1 KΩ setting

with RS

- 232 mode, as doing so will

degrade the RS

-232 signals and shorten

the communication

s . range

Pull- high resistor

Pull- low resistor

Terminator

1 KΩ

120 Ω

OFF

*150 KΩ

*–

*Default

Especificaciones del producto

Marca:	Moxa
Categoría:	servidor
Modelo:	NPort P5150A
Color del producto:	Zilver
Peso.:	150 g
Amable:	Analoog
País de origen:	Duitsland
Unidad de medida de distancia:	Metrisch
Metingbereik:	60 mm