Mtx Audio RT8PT Manual de Usario

Mtx Audio receptor RT8PT

Lee a continuación 📖 el manual en español para Mtx Audio RT8PT (24 páginas) en la categoría receptor. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/24
RT8PT
20cm (8") Powered Tube Enclosure
120W RMS
Designed in Phoenix - AZ, USA
www.mtx.eu.com
www.mtx.com
Line In
PWR
Gain
6V-0.1V 50Hz-200Hz
Rem.
Prot.
L
+
--
+
R
PWR
GND+12V
FUSE
LPF
EBC PortHLI
www.mtx.com - www.mtx.eu.com
Introduction
Thank you for purchasing an MTX Audio Hi-Performance powered tube. Proper installation matched with MTX
speakers and ampliers provide superior sound and performance for endless hours of waking the neighbors,
slammin' your friends or at out stomping wanna-be players. Congrats and enjoy the ultimate audio experience
with MTX !
Features
• Powered vented enclosure
• Subwoofer : 20cm (8")
• Amplier Max Power : 360W
• Amplier RMS Power : 120W
• EBC remote included
• High and low level inputs
• Dimensions : 25x25x54cm
Control Panel on the Amplier
Owner’s Manual - RT8PT
Speaker level inputs - This input will allow the amplier to operate from source units with speaker-level outputs.
Output speaker leads from the source unit should be tied directly to the wire harness provided with the amplier.
Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while
the EBC itself can be placed anywhere in the vehicle for on demand bass adjustments. EBC is included.
RCA Inputs - These RCA inputs are used with source units that have RCA or Line level outputs. (Source units need
a minimum level of 100mV output for proper operation of the amplier).
MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-
ated noise entering the system.
Gain Control - The gain control matches the input sensitivity of the amplier to the source unit being used. The
operating range varies from 100mv to 6V.
Adjusting the gain
1. Turn the gain control on the amplier all the way down (counter clockwise).
2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.
3. Adjust the gain control on the amplier until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The amplier is now calibrated to the output of the source unit.
Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is
adjustable from 50Hz to 200Hz..
Protection LED - When the amps is in thermal protection, the LED turns to red.
PowerOn LED - The LED illuminates red when the amp is switched on.
(+12V) Power Terminal - This is the main power input for the amplier and
must be connected directly to the positive terminal of the vehicles battery
for proper operation. Use caution when installing (+12V) power cable in
the vehicle. Avoid running this cable parallel with RCA cables, antennas, or
other sensitive equipment due to massive currents that can induce noise
into the audio system. It is also very important to have a tight, secure con-
nection for maximum performance. MTX recommends using a minimum of
6mm2 full copper power wire with the MTX RT8PT powered tube.
Remote Terminal – The powered tube can be turned on by applying 12 volts to this terminal. Typically this voltage is
supplied by a wire from the source unit marked “remote” or “power antenna”.
Ground Terminal – A proper ground is required for your amplier to operate at peak performance. A short ground
cable the same diameter as the power cable should be used to attach the ground terminal directly to the chassis of the
vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be attached.
Fuses - When the fuse blows, replace it with the same value. The RT8PT uses a 20A fuse.
Caution : Never use a higher rated fuse !
Installation & Mounting
MTX recommends your new RoadTHUNDER powered tube to be installed by an Authorized MTX retailer. Any deviation
from specied installation instructions can cause serious damage to the amplier, speakers and/or vehicles electrical
system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior
to turn on your system !
1. Disconnect the vehicle’s negative battery cable.
2. Determine the mounting place for your MTX powered enclosure. Hook it with the provided belts. Keep in mind there
should be sucient air ow for proper cooling.
3. Install a positive (+) power cable from the vehicle’s battery through the rewall using a grommet or rewall bushing
to avoid cable damage from sharp edges of the rewall. Run the cable through the interior of the vehicle and connect
it to the amplier’s (+12V) terminal (8). Do Not connect to the battery at this time.
Note : Use only proper gauge wire for both positive and negative connections.
4. Install a circuit breaker or fuse within 20cm of the battery. This eectively lowers the risk of severe damage to you
or your vehicle in case of a short circuit or accident. Make sure the circuitbreaker is switched o or the fuse is taken
out of the fuse holder untill all connections are made. Now connect your positive power cable to the positive battery
terminal of the battery.
5. Grounding - Locate a proper ground point on the vehicle’s chassis and remove all paint, dirt or debris to reveal a bare
metal surface. Attach the ground wire to that contact point. Connect the opposite end of the ground wire to the (GND)
terminal on the MTX amplier (10).
6. Connect a remote turn-on wire from the source unit to the powered tube remote terminal (9). If the source unit does
not have a dedicated Remote Turn-on lead, you may connect to the source unit’s Power Antenna lead.
7. Connecting signal cables to the amplier : There are two ways to supply the signal to your MTX powered tube.
• To get maximum performance, we suggest connecting a high quality RCA to the corresponding outputs at the source
unit and inputs of the amplier.
• If a source unit is being used without RCA outputs, use the included high-level amplier’s speaker terminals (1) using
the right gauge speaker wire.
8. Double check all previous installation steps, in particular, wiring and component connections. Once veried, recon-
nect the vehicle’s negative battery cable, turn the circuit breaker on or place the fuse in the fuse holder.
Note : Gain Levels on the amplier should be turned all the way down (counter clockwise) before proceeding with
adjustments.

Especificaciones del producto

Marca: Mtx Audio
Categoría: receptor
Modelo: RT8PT

¿Necesitas ayuda?

Si necesitas ayuda con Mtx Audio RT8PT haz una pregunta a continuación y otros usuarios te responderán


receptor Mtx Audio Manuales

Mtx Audio

Mtx Audio MUD100.4 Manual de Usario

8 Septiembre 2024
Mtx Audio

Mtx Audio XThunder 800.5 Manual de Usario

28 Agosto 2024
Mtx Audio

Mtx Audio RT8PT Manual de Usario

28 Agosto 2024
Mtx Audio

Mtx Audio JackHammer JH5001 Manual de Usario

27 Agosto 2024
Mtx Audio

Mtx Audio XThunder1200.1 Manual de Usario

26 Agosto 2024
Mtx Audio

Mtx Audio Thunder Sports MUD100.2 Manual de Usario

26 Agosto 2024
Mtx Audio

Mtx Audio RT604 Manual de Usario

25 Agosto 2024

receptor Manuales

Últimos receptor Manuales

Crown

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024
Boss

Boss PT3000 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024
Fosi Audio

Fosi Audio V3 Manual de Usario

26 Octubre 2024
Jensen

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024
Onkyo

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024
Pioneer

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024
Yamaha

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024
NAD

NAD C 355BEE Manual de Usario

20 Octubre 2024
Yamaha

Yamaha RX-A810 Manual de Usario

20 Octubre 2024