Nectre MK1 LE Manual de Usario

Nectre Calentador MK1 LE

Lee a continuación 📖 el manual en español para Nectre MK1 LE (8 páginas) en la categoría Calentador. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

Revision B

Nectre 1 MK LE

Installaon Instrucons

Keep these instrucons for future reference

Glen Dimplex Australia proudly supports the acvies of Landcare Australia through its membership of the AHHA

CONTENTS

1. INSTALLATION ................................................................... 1

1.1. IMPORTANT INFORMATION .................................... 1

1.2. FITTING REAR HEAT SHIELD ..................................... 2

1.3. INSTALLING THE HEATER ......................................... 2

1.3.1. Posioning the Heater 2 ........................................

1.3.2. Standard Installaon ........................................... 2

1.3.3. Corner Installaon 3 ..............................................

1.3.4. Clearance Dimensions ......................................... 3

1.3.5. Floor Protector .................................................... 3

1.4. REDUCING CLEARANCES TO COMBUSTIBLES .......... 3

1.5. INSTALLING THE FLUE .............................................. 4

1.6. INSTALLING FIRE BRICKS .......................................... 5

1.7. INSTALLING BAFFLE PLATES 5 .....................................

1.8. INSTALLING ASH PLATE 5 ...........................................

1.9. TECHNICAL DRAWINGS 6 ...........................................

1.9.1. MK1 Legs ............................................................. 6

1.9.2. MK1 Ped .............................................................. 6

1. INSTALLATION

1.1. IMPORTANT INFORMATION

The unit must be installed according to all manufacturers’

instrucons included in manual. The manufacturer is not this

liable for installaons that do not meet the requirements

outlined in this manual.

Most building regulatory authories in Australia require any

wood heater installaon to comply with Installaon Standard

AS/NZS 2918. Dierent states and councils may have varying

regulaons. Check local building regulaons before installing

the appliance.

All Nectre wood heaters have been tested to ensure they will

meet the appropriate safety standard requirements if the

instrucons in this manual are followed. As the safety and

emissions performance can be aected by altering the

appliance, no modicaons are allowed without wrien

permission from the manufacturer.

WE RECOMMEND THAT THE INSTALLATION OF YOUR NECTRE

WOOD HEATER BE CARRIED OUT BY A QUALIFIED INSTALLER.

WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE

INSTALLED IN ACCORDANCE WITH AS/NZS 2918 AND THE

APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING

CODE OR CODES.

WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH

THIS STANDARD SHALL COMPLY WITH THE REQUIREMENTS

OF AS/NZS 4012 & AS/NZS 4013 WHERE REQUIRED BY THE

REGULATORY AUTHORITY, I.E. THE APPLIANCE SHALL BE

IDENTIFIABLE BY A COMPLIANCE PLATE WITH THE MARKING

‘TESTED TO AS/NZS 4012 & AS/NZS 4013’.

ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN

APPROVED IN WRITING BY THE TESTING AUTHORITY IS

CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED

FOR COMPLIANCE WITH AS/NZS 4012 & AS/NZS 4013.

CAUTION: MIXING OF APPLIANCE OR FLUE-SYSTEM

COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING

THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY

RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS

CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED

IN THE FIRST INSTANCE.

CAUTION: CRACKED AND BROKEN COMPONENTS, EG. GLASS

PANELS OR CERAMIC TILES, MAY RENDER THE INSTALLATION

UNSAFE.

THE INSTALLATION INSTRUCTIONS IN THIS MANUAL

APPLY TO THE NECTRE 1 WOOD HEATER MODELS. MK LE

THEY HAVE BEEN TESTED FOR EMISSIONS AND

EFFICIENCY AND COMPLY ACCORDING TO AS/NZS 4012 &

AS/NZS 4013.

1.2. FITTING REAR HEAT SHIELD

Before working out the posion of the heater and the relevant

clearances to combusble surfaces, t the rear outer heat

shield with the curved end at the top and spacers between

the inner heat shield:

1) On the rear of the heater, there are four 32mm long PK

screws xing the outer heat shield, upside-down, to the

inner heat shield. Remove the screws and the outer heat

shield.

2) Rotate the outer heat shield 180 degrees so that the

curved end is on top and angled towards the front of the

heater.

3) A plasc packet with four 20mm long tubular spacers will

be inside the heater. Re-locate the four 32mm long PK

screws through the original holes in the outer heat shield,

slide a spacer over each screw, and re-fasten to the inner

heat shield.

1.3. INSTALLING THE HEATER

1.3.1. Posioning the Heater

Review the necessary clearances specied in this secon

before considering where to posion the heater.

Also check the praccability of installing the ue system in

relaon to any obstrucng roof beams before posioning the

heater.

The clearance distances can only be reduced if the

surrounding walls are made of non-combusble material such

as stone, brick or concrete. If non-combusble material,

distance can be reduced to 100 mm. Alternavely, shielding of

the wall(s) can reduce clearances (refer to next secon for

more detail).

Clearances to combusble surfaces vary depending on the

type of ue shielding used.

1.3.2. Standard Installaon

Dimensions given in the table and image below represent the

minimum clearance (in millimetres) to combusble materials.

A = Side clearance

B = Rear clearance

C = Minimum oor protector depth from door opening

Especificaciones del producto

Marca:	Nectre
Categoría:	Calentador
Modelo:	MK1 LE
Interruptor encendido / apagado:	Ja
Tipo de fuente de energía:	AC
Material:	MDF
Impedancia:	20000 Ohm
subwoofer de potencia media:	250 W
Altavoz de graves con controlador de diámetro (imperial):	10 "
Tipo de subwoofer:	Actieve subwoofer
Rango de frecuencia del subwoofer:	40 - 120 Hz
Ancho del subwoofer:	320 mm
Altura del subwoofer:	370 mm
Profundidad del subwoofer:	320 mm
Peso del subwoofer:	11870 g
Número de subwoofers:	1
voltaje-de-entrada-de-CA:	220-240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Altavoz de graves con controlador de diámetro:	254 mm
Entradas de línea (RCA):	1
Salidas de línea (RCA):	1